Owner's Manual - Roland

Effects List68: OVERDRIVE → DELAYfig.MFX-68L inBalance DOverdriveDelayFeedbackR inBalance DL outBalance WBalance WR outDELAY,” with the exception of the following two.Overdrive Drive → Distortion Drive, Overdrive Pan → Distortion Panfig.MFX-71L inL outBalance DBalance WDistortionDelayBalance WFeedbackR inR outBalance DParameter Value DescriptionOverdriveDrive #0–127 Degree of distortionAlso changes the volume.Overdrive Pan # L64–63R Stereo location of the overdrivesoundDelay Time 0–2600 ms, note Adjusts the delay time fromthe direct sound until the delaysound is heard.DelayFeedback #-98– +98 % Adjusts the proportion of thedelay sound that is fed backinto the effect. Negative (-)settings will invert the phase.Delay HF Damp69: DISTORTION → CHORUSThe parameters are essentially the same as in “66: OVERDRIVE →CHORUS,” with the exception of the following two.Overdrive Drive → Distortion Drive, Overdrive Pan → Distortion Panfig.MFX-69200–8000 Hz,BYPASSAdjusts the frequency abovewhich sound fed back to theeffect will be cut. If you do notwant to cut the high frequencies,set this parameter to BY-PASS.Delay Balance # D100:0W–D0:100W Adjusts the volume balancebetween the sound that is sentthrough the delay (W) and thesound that is not sent throughthe delay (D).Level 0–127 Output LevelL inR inDistortionBalance DChorusBalance DL outBalance WBalance WR out72: ENHANCER → CHORUSfig.MFX-72L inR inParameter Value DescriptionEnhancer Sens # 0–127 Sensitivity of the enhancerEnhancer Mix # 0–127 Level of the overtones generatedby the enhancerChorus PreDelay0.0–100.0 ms Adjusts the delay time from thedirect sound until the chorussound is heard.Chorus Rate # 0.05–10.00 Hz, note Frequency of modulationChorus Depth 0–127 Depth of modulationChorusBalance #73: ENHANCER → FLANGERfig.MFX-73D100:0W–D0:100WLevel 0–127 Output LevelL inEnhancerEnhancerEnhancerMixMixMixBalance DChorusBalance DAdjusts the volume balance betweenthe sound that is sentthrough the chorus (W) and thesound that is not sent throughthe chorus (D).Balance DFeedbackFlangerL outBalance WBalance WR outL outBalance WBalance W70: DISTORTION → FLANGERR inEnhancerMixBalance DR outThe parameters are essentially the same as in “67: OVERDRIVE →FLANGER,” with the exception of the following two.Overdrive Drive → Distortion Drive, Overdrive Pan → Distortion Panfig.MFX-70Balance DL inDistortionR inFeedback71: DISTORTION → DELAYL outBalance WFlangerBalance WR outBalance DThe parameters are essentially the same as in “68: OVERDRIVE →Parameter Value DescriptionEnhancer Sens # 0–127 Sensitivity of the enhancerEnhancer Mix # 0–127 Level of the overtones generatedby the enhancerFlanger PreDelay0.0–100.0 ms Adjusts the delay time fromwhen the direct sound beginsuntil the flanger sound is heard.Flanger Rate # 0.05–10.00 Hz, note Frequency of modulationFlanger Depth 0–127 Depth of modulationFlangerFeedback #FlangerBalance #-98– +98 % Adjusts the proportion of theflanger sound that is fed backinto the effect. Negative (-) settingswill invert the phase.D100:0W–D0:100WLevel 0–127 Output LevelAdjusts the volume balance betweenthe sound that is sentthrough the flanger (W) and thesound that is not sent throughthe flanger (D).290