Owner's Manual - Roland

Effects List47: 3TAP PAN DELAYProduces three delay sounds; center, left and right.fig.MFX-47L inR inParameter Value DescriptionDelay Left/Right/Center0–2600 ms,noteAdjusts the time until the delay soundis heard.CenterFeedback #-98– +98 % Adjusts the amount of the delay soundthat’s fed back into the effect. Negative(-) settings invert the phase.HF Damp200–8000 Hz,BYPASS48: 4TAP PAN DELAYThis effect has four delays.fig.MFX-48aAdjusts the frequency above whichsound fed back to the effect is filteredout. If you do not want to filter out anyhigh frequencies, set this parameter toBYPASS.Left/Right/ 0–127 Volume of each delayCenter LevelLow Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeBalance # D100:0W–D0:100WVolume balance between the directsound (D) and the delay sound (W)Level 0–127 Output levelL inR in1Lfig.MFX-48bStereo location of each delayParameter Value DescriptionDelay 1–4Time0–2600 ms,noteAdjusts the time until the delay soundis heard.Delay 1Feedback #-98– +98 % Adjusts the amount of the delay soundthat’s fed back into the effect. Negative(-) settings invert the phase.HF DampTriple Tap DelayFeedback2 3Feedback200–8000 Hz,BYPASSLeft TapRight TapDelay 1Balance DCenter TapQuadruple Tap DelayR4Delay 4Balance DDelay 2Delay 32-BandEQBalance WBalance DBalance W2-BandEQBalance DL outR outL outBalance WBalance WR outAdjusts the frequency above whichsound fed back to the effect is filteredout. If you do not want to filter out anyhigh frequencies, set this parameter toBYPASS.Delay 1–4 0–127 Volume of each delayLevelLow Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeBalance # D100:0W–D0:100WVolume balance between the directsound (D) and the delay sound (W)Level 0–127 Output level49: MULTI TAP DELAYThis effect provides four delays. Each of the Delay Time parameterscan be set to a note length based on the selected tempo. You can alsoset the panning and level of each delay sound.fig.MFX-49L inR inParameter Value DescriptionDelay 1–4Time0–2600 ms,noteAdjusts the time until Delays 1–4 areheard.Delay 1Feedback #-98– +98 % Adjusts the amount of the delay soundthat’s fed back into the effect. Negative(-) settings invert the phase.HF Damp50: REVERSE DELAYThis is a reverse delay that adds a reversed and delayed sound to theinput sound. A tap delay is connected immediately after the reversedelay.fig.MFX-50200–8000 Hz,BYPASSAdjusts the frequency above whichsound fed back to the effect is filteredout. If you don’t want to filter out anythe high frequencies, set this parameterto BYPASS.Delay 1–4 L64–63R Stereo location of Delays 1–4PanDelay 1–4 0–127 Output level of Delays 1–4LevelLow Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeBalance # D100:0W–D0:100WVolume balance between the directsound (D) and the effect sound (W)Level 0–127 Output levelL inR inParameter Range ExplanationThreshold 0–127 Volume at which the reversedelay will begin to be appliedRev DelayTimeRev DelayFeedback #0–1300 ms, note Delay time from when soundis input into the reverse delayuntil the delay sound is heard-98– +98% Proportion of the delay soundthat is to be returned to the inputof the reverse delay (negativevalues invert the phase)Rev Delay HFDamp200–8000 Hz,BYPASSFrequency at which the highfrequencycontent of the reverse-delayedsound will becut (BYPASS: no cut)Rev Delay Pan L64–63R Panning of the reverse delaysoundRev DelayLevel0–127 Volume of the reverse delaysoundDelay 1 – 3TimeFeedbackMulti Tap DelayFeedbackDelay 1Delay 2Rev. DelayDelay 3Delay 4Balance DBalance DRevD1DelayD2D32-BandEQBalance WBalance W2-BandEQ2-BandEQ2-BandEQL outR outL outR out0–1300 ms, note Delay time from when soundis input into the tap delay untilthe delay sound is heard284