Owner's Manual - Roland

Effects List40: COMPRESSORFlattens out high levels and boosts low levels, smoothing outfluctuations in volume.fig.MFX-40L in Compressor 2-Band EQ L outParameter Value DescriptionHold 0–127 Adjusts the time it takes for the gate tostart closing after the source sound fallsbeneath the Threshold.Release 0–127 Adjusts the time it takes the gate to fullyclose after the hold time.Balance # D100:0W–D0:100WVolume balance between the directsound (D) and the effect sound (W)Level 0–127 Output levelR inCompressor2-Band EQR out43: DELAYParameter Value DescriptionAttack # 0–127 Sets the speed at which compressionstartsThreshold # 0–127 Adjusts the volume at which compressionbeginsPost Gain 0– +18 dB Adjusts the output gain.Low Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeLevel # 0–127 Output level41: LIMITERCompresses signals that exceed a specified volume level, preventingdistortion from occurring.fig.MFX-41L inLimiter2-Band EQL outThis is a stereo delay.When Feedback Mode is NORMAL:fig.MFX-43aL inR inWhen Feedback Mode is CROSS:fig.MFX-43bDelayFeedbackFeedbackDelayBalance DBalance D2-BandEQBalance WBalance W2-BandEQL outR outR inLimiter2-Band EQR outL inDelayBalance D2-BandEQBalance WL outParameter Value DescriptionRelease # 0–127 Adjusts the time after the signal volumefalls below the Threshold Level untilcompression is no longer applied.Threshold # 0–127 Adjusts the volume at which compressionbeginsRatio 1.5:1, 2:1, 4:1, Compression ratio100:1Post Gain 0– +18 dB Adjusts the output gain.Low Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeLevel # 0–127 Output level42: GATECuts the reverb’s delay according to the volume of the sound sentinto the effect. Use this when you want to create an artificialsoundingdecrease in the reverb’s decay.fig.MFX-42L inR inParameter Value DescriptionThreshold # 0–127 Volume level at which the gate begins tocloseModeGATE,DUCKGateGateL outR outType of gateGATE: The gate will close when thevolume of the original sound decreases,cutting the original sound.DUCK (Ducking): The gate will closewhen the volume of the originalsound increases, cutting the originalsound.Attack 0–127 Adjusts the time it takes for the gate tofully open after being triggered.R inParameter Value DescriptionDelay Left 0–1300 ms, Adjusts the time until the delay sound isDelay Right noteheard.Phase Left NORMAL,INVERSEPhase of the delay soundPhase RightFeedbackModeNORMAL,CROSSSelects the way in which delay sound isfed back into the effect. (See the figuresabove.)Feedback # -98– +98 % Adjusts the amount of the delay soundthat’s fed back into the effect. Negative(-) settings invert the phase.HF DampFeedbackFeedbackDelay200–8000 Hz,BYPASSBalance DBalance W2-BandEQR outAdjusts the frequency above which soundfed back to the effect is filtered out. If youdon’t want to filter out any high frequencies,set this parameter to BYPASS.Low Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeBalance # D100:0W–D0:100WVolume balance between the directsound (D) and the delay sound (W)Level 0–127 Output level282