Owner's Manual - Roland

Effects List30: 3D FLANGERThis applies a 3D effect to the flanger sound. The flanger sound willbe positioned 90 degrees left and 90 degrees right.fig.MFX-30LRParameter Value DescriptionFilter Type OFF, LPF, HPF Type of filterOFF: no filter is usedLPF: cuts the frequencyrange above the Cutoff FreqHPF: cuts the frequencyrange below the Cutoff FreqCutoff Freq 200–8000 Hz Basic frequency of the filterPre Delay 0.0–100.0 ms Adjusts the delay time fromwhen the direct sound beginsuntil the flanger sound isheard.Rate # 0.05–10.00 Hz, note Frequency of modulationDepth 0–127 Depth of modulationPhase 0–180 deg Spatial spread of the soundFeedback # -98– +98 % Adjusts the proportion of theflanger sound that is fed backinto the effect. Negative (-) settingswill invert the phase.Output Mode SPEAKER, PHONES Adjusts the method that will beused to hear the sound that isoutput to the OUTPUT jacks.The optimal 3D effect will beachieved if you select SPEAK-ER when using speakers, orPHONES when using headphones.Low Gain -15– +15 dB Gain of the low rangeHigh Gain -15– +15 dB Gain of the high rangeBalance # D100:0W–D0:100W Volume balance between thedirect sound (D) and theflanger sound (W)Level 0–127 Output Level31: 3D STEP FLANGERThis applies a 3D effect to the step flanger sound. The flanger soundwill be positioned 90 degrees left and 90 degrees right.fig.MFX-31LR3D Flanger3D Step Flanger2-BandEQ2-BandEQ2-BandEQ2-BandEQL outR outL outR outParameter Value DescriptionFilter Type OFF, LPF, HPF Type of filterOFF: no filter is usedLPF: cuts the frequencyrange above the Cutoff FreqHPF: cuts the frequencyrange below the Cutoff FreqCutoff Freq 200–8000 Hz Basic frequency of the filterPre Delay 0.0–100.0 ms Adjusts the delay time fromwhen the direct sound beginsuntil the flanger sound isheard.Rate # 0.05–10.00 Hz, note Frequency of modulationDepth 0–127 Depth of modulationPhase 0–180 deg Spatial spread of the soundParameter Value DescriptionFeedback # -98– +98 % Adjusts the proportion of theflanger sound that is fed backinto the effect. Negative (-) settingswill invert the phase.Step Rate # 0.10–20.00 Hz, note Rate (period) of pitch changeOutput Mode SPEAKER, PHONES Adjusts the method that will beused to hear the sound that isoutput to the OUTPUT jacks.The optimal 3D effect will beachieved if you select SPEAK-ER when using speakers, orPHONES when using headphones.Low Gain -15– +15 dB Gain of the low rangeHigh Gain -15– +15 dB Gain of the high rangeBalance # D100:0W–D0:100W Volume balance between thedirect sound (D) and theflanger sound (W)Level 0–127 Output Level32: 2BAND CHORUSA chorus effect that lets you apply an effect independently to thelow-frequency and high-frequency ranges.fig.MFX-32L inR inSplitSplitHigh Band ChorusLow Band ChorusHigh Band ChorusLow Band ChorusL outR outParameter Range ExplanationSplit Freq 200–8000 Hz Frequency at which the lowand high ranges will be dividedLow Pre Delay 0.0–100.0 ms Delay time from when theoriginal sound is heard towhen the low-range chorussound is heardLow Rate # 0.05–10.00 Hz, note Rate at which the low-rangechorus sound is modulatedLow Depth 0–127 Modulation depth for the lowrangechorus soundLow Phase 0–180 deg Spaciousness of the low-rangechorus soundHigh Pre Delay 0.0–100.0 ms Delay time from when theoriginal sound is heard towhen the high-range chorussound is heardHigh Rate # 0.05–10.00 Hz, note Rate at which the low-rangechorus sound is modulatedHigh Depth 0–127 Modulation depth for thehigh-range chorus soundHigh Phase 0–180 deg Spaciousness of the highrangechorus soundBalance # D100:0W–D0:100W Volume balance of the originalsound (D) and chorussound (W)Level 0–127 Output volume279