Owner's Manual - Roland

Effects List15: RING MODULATORThis is an effect that applies amplitude modulation (AM) to the inputsignal, producing bell-like sounds. You can also change themodulation frequency in response to changes in the volume of thesound sent into the effect.fig.MFX-15L in Ring Mod 2-Band EQ L outParameterMod WaveValueTRI, SQR, SIN,SAW1, SAW2SAW1DescriptionModulation WaveTRI: triangle waveSQR: square waveSIN: sine waveSAW1/2: sawtooth waveSAW2R inParameter Value DescriptionFrequency # 0–127 Adjusts the frequency at which modulationis applied.Sens # 0–127 Adjusts the amount of frequency modulationapplied.Polarity UP, DOWN Determines whether the frequency modulationmoves towards higher frequencies(UP) or lower frequencies (DOWN).Low Gain -15– +15 dB Gain of the low frequency rangeHigh Gain -15– +15 dB Gain of the high frequency rangeBalance # D100:0W–D0:100WVolume balance between the directsound (D) and the effect sound (W)Level 0–127 Output level16: STEP RING MODULATORThis is a ring modulator that uses a 16-step sequence to vary thefrequency at which modulation is applied.fig.MFX-16L inRing ModStep Ring Mod2-Band EQ2-Band EQR outL outRate # 0.05–10.00 Hz, note Frequency of the changeDepth # 0–127 Depth to which the effect is appliedLow Gain -15– +15 dB Gain of the low rangeHigh Gain -15– +15 dB Gain of the high rangeLevel 0–127 Output Level18: AUTO PANCyclically modulates the stereo location of the sound.fig.MFX-18aL inR inParameterMod WaveAuto PanAuto PanValueTRI, SQR, SIN,SAW1, SAW22-Band EQ2-Band EQDescriptionL outR outModulation WaveTRI: triangle waveSQR: square waveSIN: sine waveSAW1/2: sawtooth waveR inStep Ring Mod2-Band EQR outSAW1RSAW2RParameter Range ExplanationStep 01–16 0–127 Frequency of ring modulation ateach stepRate # 0.05–10.00 Hz, note Rate at which the 16-step sequencewill cycleAttack # 0–127 Speed at which the modulationfrequency changes betweenstepsLow Gain -15– +15 dB Amount of boost/cut for thelow-frequency rangeHigh Gain -15– +15 dB Amount of boost/cut for thehigh-frequency rangeBalance # D100:0W–D0:100WVolume balance of the originalsound (D) and effect sound (W)Level 0–127 Output volumeRate # 0.05–10.00 Hz, note Frequency of the changeDepth # 0–127 Depth to which the effect is appliedLow Gain -15– +15 dB Gain of the low rangeHigh Gain -15– +15 dB Gain of the high rangeLevel 0–127 Output Level19: STEP PANThis uses a 16-step sequence to vary the panning of the sound.fig.MFX-19L inLStep PanLL outR inStep PanR out17: TREMOLOCyclically modulates the volume to add tremolo effect to the sound.fig.MFX-17aL in Tremolo 2-Band EQ L outR in Tremolo 2-Band EQ R outParameter Range ExplanationStep 01–16 L64–63R Pan at each stepRate # 0.05–10.00 Hz, note Rate at which the 16-step sequencewill cycleAttack # 0–127 Speed at which the pan changesbetween stepsInput SyncSwOFF, ONSpecifies whether an input notewill cause the sequence to resumefrom the first step of the sequence(ON) or not (OFF)0–127 Volume at which an input notewill be detectedInput SyncThresholdLevel 0–127 Output volume275