SCSI Primary Commands - 2.pdf

More documents

Recommendations

Info

T10/1236-D Revision 20 18 July 2001Support for a value of one in the TUR (Test Unit Ready) bit is optional. If a TUR value of one is supported and theTUR bit contains one, then a TEST UNIT READY command (see 7.25) shall be used to determine the readiness ofthe device. If a TUR value of one is not supported and the TUR bit contains one, then the EXTENDED COPYcommand shall be terminated with a CHECK CONDITION status. The sense key shall be set to COPY ABORTEDand the additional sense code shall be set to INVALID FIELD IN PARAMETER LIST. The SENSE-KEY SPECIFIC fieldshall be set as described in 7.2.3. If the TUR bit contains zero, then the accessibility should be verified withoutdisturbing established unit attention or ACA conditions, for example, using the INQUIRY command (see 7.3).7.2.7.11 Block device with offset to stream device operationThe segment descriptor format shown in table 38 is used to instruct the copy manager to move data from a blockdevice with a byte offset to a stream device or vice versa.Table 38 — Block device with offset to or from stream device segment descriptorBitByte7 6 5 4 3 2 1 00 DESCRIPTOR TYPE CODE (08h or 09h)1 Reserved CAT2 (MSB)DESCRIPTOR LENGTH (0018h)3 (LSB)4 (MSB)SOURCE TARGET DESCRIPTOR INDEX5 (LSB)6 (MSB)DESTINATION TARGET DESCRIPTOR INDEX7 (LSB)8 Reserved9 (MSB)10STREAM DEVICE TRANSFER LENGTH11 (LSB)12 (MSB)NUMBER OF BYTES15 (LSB)16 (MSB)BLOCK DEVICE LOGICAL BLOCK ADDRESS23 (LSB)24 Reserved25 Reserved26 (MSB)BLOCK DEVICE BYTE OFFSET27 (LSB)The DESCRIPTOR TYPE CODE field is described in 7.2.5 and 7.2.7.1. Descriptor type code 08h (block→stream)instructs the copy manager to copy the data from the source block device identified by the SOURCE TARGETDESCRIPTOR INDEX field to the destination stream device identified by the DESTINATION TARGET DESCRIPTOR INDEXfield using data starting at the location identified by the BLOCK DEVICE BYTE OFFSET field in the logical block identifiedby the BLOCK DEVICE LOGICAL BLOCK ADDRESS field and continuing for the number of bytes specified in the NUMBEROF BYTES field. The data shall be written to the stream device starting at the current position of the media.72 dpANS SCSI Primary Commands - 2 (SPC-2)
18 July 2001 T10/1236-D Revision 20The CAT bit is described in 7.2.7.2.The DESCRIPTOR LENGTH field shall contain 24 (0018h). The SOURCE TARGET DESCRIPTOR INDEX and DESTINATIONTARGET DESCRIPTOR INDEX fields are described in 7.2.7.1.The STREAM DEVICE TRANSFER LENGTH field specifies the amount of data to be written on each write operation to thestream device. See 7.2.6.8 for a description of how data in the STREAM DEVICE TRANSFER LENGTH field in thesegment descriptor interacts with data in the STREAM BLOCK LENGTH field in the device type specific targetdescriptor parameters for the sequential-access device type.The NUMBER OF BYTES field specifies the number bytes to be read. A value of zero indicates that no bytes shall betransferred in this segment. This shall not be considered as an error.The BLOCK DEVICE LOGICAL BLOCK ADDRESS field specifies the starting logical block address on the source blockdevice for this segment.The BLOCK DEVICE BYTE OFFSET field specifies the offset into the first source block at which to begin reading bytes.7.2.7.12 Stream device to block device with offset operationThe segment descriptor format shown in table 38 (see 7.2.7.11) also is used to instruct the copy manager to movedata from a stream device to a block device with a byte offset.The DESCRIPTOR TYPE CODE field is described in 7.2.5 and 7.2.7.1. Descriptor type code 09h (stream→block)instructs the copy manager to copy the data from the source stream device identified by the SOURCE TARGETDESCRIPTOR INDEX field to the destination block device identified by the DESTINATION TARGET DESCRIPTOR INDEX fieldusing the stream data starting at the current position of the stream device. The data shall be written starting at thelocation identified by the BLOCK DEVICE BYTE OFFSET field in the logical block identified by the BLOCK DEVICE LOGICALBLOCK ADDRESS field and continuing for the number of bytes specified in the NUMBER OF BYTES field.The content of the starting logical block on the destination device before the starting offset shall be preserved. Thecontent on the ending logical block beyond the end of the transfer shall be preserved. The copy manager mayimplement this operation by reading the starting and ending logical blocks, modifying a portion of the blocks asrequired, and writing the full blocks to the destination device.The CAT bit is described in 7.2.7.2.The DESCRIPTOR LENGTH field shall contain 24 (0018h). The SOURCE TARGET DESCRIPTOR INDEX and DESTINATIONTARGET DESCRIPTOR INDEX fields are described in 7.2.7.1.The STREAM DEVICE TRANSFER LENGTH field specifies the amount of data to be written on each write operation to thestream device. See 7.2.6.8 for a description of how data in the STREAM DEVICE TRANSFER LENGTH field in thesegment descriptor interacts with data in the STREAM BLOCK LENGTH field in the device type specific targetdescriptor parameters for the sequential-access device type.The NUMBER OF BYTES field specifies the number bytes to be read. A value of zero indicates that no bytes shall betransferred in this segment. This shall not be considered as an error.The BLOCK DEVICE LOGICAL BLOCK ADDRESS field specifies the starting logical block address on the destination blockdevice for this segment.The BLOCK DEVICE BYTE OFFSET field is the offset into the first destination block at which to begin writing data to thedestination block device.dpANS SCSI Primary Commands - 2 (SPC-2) 73
Page 1 and 2:
dpANSProjectT10/1236-DRevision 2018
Page 3:
DraftANSI (r)NCITS.351:200xAmerican
Page 6 and 7:
T10/1236-D Revision 20 18 July 2001
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41: T10/1236-D Revision 20 18 July 2001
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Page 186 and 187:
Page 188 and 189:
Page 190 and 191:
Page 192 and 193:
Page 194 and 195:
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
show all

SCSI Primary Commands - 2.pdf

Create successful ePaper yourself

Delete template?

Save as template?