SCSI Primary Commands - 2.pdf

More documents

Recommendations

Info

T10/1236-D Revision 20 18 July 2001The IDENTIFIER TYPE field specifies the format and assignment authority for the identifier, as described in table 174.At least one identification descriptor shall contain 1h, 2h, or 3h in the IDENTIFIER TYPE field and 0h in the ASSOCI-ATION field. At least one identification descriptor should contain 2h or 3h in the IDENTIFIER TYPE field and 0h in theASSOCIATION field.Table 174 — Identifier typeValue0h1h2h3h4h5h - FhDescriptionNo assignment authority was used and consequently there is no guarantee that the identifieris globally unique (i.e., the identifier is vendor specific)The first eight bytes of the identifier field are a Vendor ID (see Annex D). The organizationassociated with the Vendor ID is responsible for ensuring that the remainder of the identifierfield is unique. One recommended method of constructing the remainder of the identifierfield is to concatenate the product identification field from the standard INQUIRY data fieldand the product serial number field from the unit serial number page.The identifier field contains a canonical form IEEE Extended Unique Identifier, 64-bit(EUI-64). In this case, the identifier length field shall be set to eight. Note that the IEEEguidelines for EUI-64 specify a method for unambiguously encapsulating an IEEE 48-bitidentifier within an EUI-64.The identifier field contains an FC-FS Name_Identifier. Any FC-FS identifier may be used,including one of the four based on a Canonical form IEEE company_id.If the ASSOCIATION value is 1h, the IDENTIFIER value contains a four-byte binary number identifyingthe port relative to other ports in the device using the values shown table 175. In thiscase, the CODE SET field shall be set to 1h and the IDENTIFIER LENGTH field shall be set to 4. Ifthe ASSOCIATION value is not 1h, use of this identifier type is reserved.ReservedTable 175 — Relative port identifier valuesValueDescription0hReserved1hRelative port 1, historically known as port A2hRelative port 2, historically known as port B3h-7FFFFFFFh Relative port 3 through 2 147 483 64780000000h-FFFFFFFFh ReservedThe IDENTIFIER LENGTH field specifies the length in bytes of the IDENTIFIER field. If the allocation length field of theCDB is too small to transfer all of the identifier, the identifier length shall not be adjusted to reflect the truncation.The IDENTIFIER field contains the identifier as described by the ASSOCIATION, IDENTIFIER TYPE, CODE SET, andIDENTIFIER LENGTH fields.The example described in this paragraph and shown in table 176 is not a normative part of this standard. Thisexample of a complete device identification VPD page assumes that the product is a direct-access device with anT10 Vendor ID of “XYZ_Corp”, a product identification of “Super Turbo Disk”, and a product serial number of“2034589345”. Furthermore, it is assumed that the manufacturer has been assigned a 24-bit IEEE company_id of01ABCDh by the IEEE Registration Authority Committee and that the manufacture has assigned a 24-bitextension_identifier of 234567h to this logical unit. The combined 48-bit identifier is reported in the 64-bit format as212 dpANS SCSI Primary Commands - 2 (SPC-2)
18 July 2001 T10/1236-D Revision 20defined by the IEEE 64-bit Global Identifier (EUI-64) standard. The data returned in the device identification VPDpage for this logical unit is shown in table 176.8.4.5 Supported vital product data pagesTable 176 — Device identification page exampleBytes Hexadecimal values ASCII values00 – 15 00 83 00 32 02 01 00 22 58 59 5A 5F 43 6F 72 70 ...2..."XYZ_Corp16 – 31 53 75 70 65 72 20 54 75 72 62 6F 20 44 69 73 6B Super Turbo Disk32 – 47 32 30 33 34 35 38 39 33 34 35 01 02 00 08 01 AB 2034589345......48 – 53 CD FF FF 23 45 67 ......NOTE 1 Non-printing ASCII characters are shown as '.'.NOTE 2 Byte 00 is the beginning of the VPD page (see table 170).NOTE 3 Byte 04 is the beginning of the Identification descriptor for the Vendor ID based identifier(Identifier type 1, see table 174).NOTE 4 Byte 42 is the beginning of the Identification descriptor for the EUI-64 identifier (Identifiertype 2, see table 174).This contains a list of the vital product data page codes supported by the target or logical unit (see table 177). If adevice server supports any vital product data pages, it also shall support this vital product data page.Table 177 — Supported vital product data pagesBitByte7 6 5 4 3 2 1 00 PERIPHERAL QUALIFIER PERIPHERAL DEVICE TYPE1 PAGE CODE (00h)2 Reserved3 PAGE LENGTH (n-3)4nSUPPORTED PAGE LISTThe PERIPHERAL QUALIFIER field and the PERIPHERAL DEVICE TYPE field are defined in 7.3.2.The PAGE LENGTH field specifies the length of the supported page list. If the allocation length is too small to transferall of the page, the page length shall not be adjusted to reflect the truncation.The SUPPORTED PAGE LIST field shall contain a list of all vital product data page codes (see 8.4) implemented for thetarget or logical unit in ascending order beginning with page code 00h.dpANS SCSI Primary Commands - 2 (SPC-2) 213
Page 1 and 2:
dpANSProjectT10/1236-DRevision 2018
Page 3:
DraftANSI (r)NCITS.351:200xAmerican
Page 6 and 7:
T10/1236-D Revision 20 18 July 2001
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163:
Page 164 and 165:
Page 166 and 167:
Page 168 and 169:
Page 170 and 171:
Page 172 and 173:
Page 174 and 175:
Page 176 and 177:
Page 178 and 179:
Page 180 and 181: T10/1236-D Revision 20 18 July 2001
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
show all

SCSI Primary Commands - 2.pdf

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?