SCSI Primary Commands - 2.pdf

More documents

Recommendations

Info

T10/1236-D Revision 20 18 July 2001d) If the number of blocks is set to FFFFFFFFFFFFFFFFh, the device shall be set to its maximum capacity. Ifthe block size has not changed, the device shall not become format corrupted. This capacity setting shallbe retained through reset events or power cycles.NOTE 48 There may be implicit association between parameters defined in the pages and block descriptor. Fordirect-access devices, the block length affects the optimum values (i.e., the values that achieves the best performance)for the sectors per track, bytes per physical sector, track skew factor, and cylinder skew factor fields in theformat parameters page. In this case, the target may change parameters not explicitly sent with the MODESELECT command. A subsequent MODE SENSE command may be used to detect these changes.The DENSITY CODE field is unique for each device type. Refer to the mode parameters subclause of the specificdevice type command standard (see 3.1.12) for the definition of this field. Some device types reserve all or part ofthis field.The BLOCK LENGTH field specifies the length in bytes of each logical block described by the block descriptor.8.3.5 Mode page format and page codesThe mode page format is defined in table 152.Table 152 — Mode page formatBitByte7 6 5 4 3 2 1 00 PS Reserved PAGE CODE1 PAGE LENGTH (n-1)2nMode parametersEach mode page contains a PAGE CODE field, a PAGE LENGTH field, and a set of mode parameters. The page codesare defined in this subclause and in the mode parameter subclauses in the command standard (see 3.1.12) for thespecific device type.When using the MODE SENSE command, a parameters savable (PS) bit of one indicates that the mode page maybe saved by the target in a nonvolatile, vendor specific location. A PS bit of zero indicates that the supportedparameters cannot be saved. When using the MODE SELECT command, the PS bit is reserved.The PAGE CODE field identifies the format and parameters defined for that mode page. Some page codes aredefined as applying to all device types and other page codes are defined for the specific device type. The pagecodes that apply to a specific device type are defined in the command standard (see 3.1.12) for that device type.When using the MODE SENSE command, if page code 00h (vendor specific page) is implemented, the deviceserver shall return that page last in response to a request to return all pages (page code 3Fh). When using theMODE SELECT command, this page should be sent last.The PAGE LENGTH field specifies the length in bytes of the mode parameters that follow. If the application clientdoes not set this value to the value that is returned for the page by the MODE SENSE command, the device servershall terminate the command with CHECK CONDITION status. The sense key shall be set to ILLEGAL REQUESTwith the additional sense code set to INVALID FIELD IN PARAMETER LIST. The target is permitted to implementa mode page that is less than the full page length defined in this standard, provided no field is truncated and thePAGE LENGTH field correctly specifies the actual length implemented.194 dpANS SCSI Primary Commands - 2 (SPC-2)
18 July 2001 T10/1236-D Revision 20The mode parameters for each page are defined in the following subclauses, or in the mode parameters subclausein the command standard (see 3.1.12) for the specific device type. Mode parameters not implemented by thetarget shall be set to zero.Table 153 defines the mode pages that are applicable to all device types that implement the MODE SELECT andMODE SENSE commands.Table 153 — Mode page codesPage code Description Reference0Ah Control mode page 8.3.602h Disconnect-reconnect page 8.3.71Ch Informational exceptions control page 8.3.809h obsolete 3.3.71Ah Power condition page 8.3.918h Protocol specific LUN page 8.3.1019h Protocol specific port page 8.3.1101h (See specific device type)03h - 08h (See specific device type)0Bh - 17h (See specific device type)1Bh (See specific device type)1Dh - 1Fh (See specific device type)00h Vendor specific (does not require page format)20h - 3Eh (See specific device type)3Fh Return all pages (valid only for the MODE SENSE command)dpANS SCSI Primary Commands - 2 (SPC-2) 195
Page 1 and 2:
dpANSProjectT10/1236-DRevision 2018
Page 3:
DraftANSI (r)NCITS.351:200xAmerican
Page 6 and 7:
T10/1236-D Revision 20 18 July 2001
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157:
Page 158 and 159:
Page 160 and 161:
Page 162 and 163: T10/1236-D Revision 20 18 July 2001
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
show all

SCSI Primary Commands - 2.pdf

Create successful ePaper yourself

Delete template?

Save as template?