SCSI Primary Commands - 2.pdf

More documents

Recommendations

Info

T10/1236-D Revision 20 18 July 2001The temperature sensed in the device at the time the LOG SENSE command is performed shall be returned in theparameter field defined by parameter code 0000h. The one byte binary value specifies the temperature of thedevice in degrees Celsius. Temperatures equal to or less than zero degrees Celsius shall be indicated by a valueof zero. If the device server is unable to detect a valid temperature because of a sensor failure or other condition,the value returned shall be FFh. The temperature should be reported with an accuracy of plus or minus threeCelsius degrees while the device is operating at a steady state within the environmental limits specified for thedevice. No comparison is performed between the temperature value specified in parameter 0000h and thereference temperature specified in parameter 0001h. The state of the parameter control bits for parameter 0000his specified in table 145.Table 145 — Parameter control bits for temperature parameters (0000h and 0001h)Bit Value DescriptionDU 0 Value provided by device serverDS 1 Device server does not support saving of parameterTSD 0 Device server manages saving of parameterETC 0 No threshold comparison is made on this valueTMC xx Ignored when ETC is 0LBIN 1 The parameter is in binary formatLP 1 The parameter is a list parameterA reference temperature for the device may optionally be provided by the device using parameter code 0001h. Ifno reference temperature is provided, the parameter may not be provided in the log page or alternatively, thereference temperature value may be set to the value of FFh. The one byte binary value should reflect themaximum reported sensor temperature in degrees Celsius at which the device is capable of operating continuouslywithout degrading the device's operation or reliability beyond manufacturer accepted limits. The reference temperaturemay change for vendor specific reasons. The state of the parameter control bits for parameter 0001h isspecified in table 145.188 dpANS SCSI Primary Commands - 2 (SPC-2)
18 July 2001 T10/1236-D Revision 208.3 Mode parameters8.3.1 Mode parameters overviewThis subclause describes the block descriptors and the pages used with MODE SELECT and MODE SENSEcommands that are applicable to all SCSI devices. Pages specific to each device type are described in thecommand standard (see 3.1.12) that applies to that device type.8.3.2 Mode parameter list formatThe mode parameter list shown in table 146 contains a header, followed by zero or more block descriptors, followedby zero or more variable-length pages. Parameter lists are defined for each device type.Table 146 — Mode parameter listBitByte7 6 5 4 3 2 1 00 - n Mode parameter header0 - n Block descriptor(s)0 - n Page(s)8.3.3 Mode parameter header formatsThe six-byte CDB mode parameter header is defined in table 147.Table 147 — Mode parameter header(6)BitByte7 6 5 4 3 2 1 00 MODE DATA LENGTH1 MEDIUM TYPE2 DEVICE-SPECIFIC PARAMETER3 BLOCK DESCRIPTOR LENGTHdpANS SCSI Primary Commands - 2 (SPC-2) 189
Page 1 and 2:
dpANSProjectT10/1236-DRevision 2018
Page 3:
DraftANSI (r)NCITS.351:200xAmerican
Page 6 and 7:
T10/1236-D Revision 20 18 July 2001
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145:
Page 146 and 147:
Page 148 and 149:
Page 150 and 151:
Page 152 and 153:
Page 154 and 155:
Page 156 and 157: T10/1236-D Revision 20 18 July 2001
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
show all

SCSI Primary Commands - 2.pdf

Create successful ePaper yourself

Delete template?

Save as template?