SCSI Primary Commands - 2.pdf

More documents

Recommendations

Info

T10/1236-D Revision 20 18 July 2001The page code assignments for the log pages are listed in table 126.Table 126 — Log page codesPage Code Description Reference0Fh Application client page01h Buffer over-run/under-run page 8.2.303h Error counter page (read) page 8.2.404h Error counter page (read reverse) page 8.2.405h Error counter page (verify) page 8.2.402h Error counter page (write) page 8.2.40Bh Last n deferred errors or asynchronous events page 8.2.507h Last n error events page 8.2.606h Non-medium error page 8.2.710h Self-test results page 8.2.80Eh Start-stop cycle counter page 8.2.900h Supported log pages 8.2.100Dh Temperature page 8.2.1108h - 0Ah Reserved (may be used by specific device types)0Ch Reserved (may be used by specific device types)11h - 2Fh Reserved (may be used by specific device types)3Fh Reserved30h - 3Eh Vendor specific pages176 dpANS SCSI Primary Commands - 2 (SPC-2)
18 July 2001 T10/1236-D Revision 208.2.2 Application client pageThe application client page (see table 127) provides a place for application clients to store information. The pagecode for the application client page is 0Fh.Table 127 — Application client pageBitByte7 6 5 4 3 2 1 00 PAGE CODE (0Fh)1 Reserved2 (MSB)PAGE LENGTH (n-3)3 (LSB)Application client log parameters4First application client log parameter..nLast application client log parameterThe PAGE CODE and PAGE LENGTH fields are described in 8.2.1.Parameter codes 0000h through 0FFFFh are for general usage application client data. The intended use for thisinformation is to aid in describing the system configuration and system problems, but the exact definition of the datais application client specific. The general usage application client data parameters all have the format shown intable 128.Table 128 — General usage application client parameter dataBitByte7 6 5 4 3 2 1 00 (MSB)PARAMETER CODE1 (LSB)2 DU DS TSD ETC TMC LBIN LP3 PARAMETER LENGTH (FCh)4255GENERAL USAGE PARAMETER BYTESFor general usage application client data, the value in the PARAMETER CODE field shall be between 0000h and0FFFh. The first supported general usage application client parameter code shall be 0000h and additionalsupported parameters shall be sequentially numbered. If any general usage parameter codes are implemented,the device shall support at least 64 general usage parameter descriptors and they shall be parameter codes 0000hthrough 003Fh.For the general usage application client parameter, the PARAMETER LENGTH value for each parameter shall be FCh.dpANS SCSI Primary Commands - 2 (SPC-2) 177
Page 1 and 2:
dpANSProjectT10/1236-DRevision 2018
Page 3:
DraftANSI (r)NCITS.351:200xAmerican
Page 6 and 7:
T10/1236-D Revision 20 18 July 2001
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103:
Page 104 and 105:
Page 106 and 107:
Page 108 and 109:
Page 110 and 111:
Page 112 and 113:
Page 114 and 115:
Page 116 and 117:
Page 118 and 119:
Page 120 and 121:
Page 122 and 123:
Page 124 and 125:
Page 126 and 127:
Page 128 and 129:
Page 130 and 131:
Page 132 and 133:
Page 134 and 135:
Page 136 and 137:
Page 138 and 139:
Page 140 and 141:
Page 142 and 143:
Page 144 and 145: T10/1236-D Revision 20 18 July 2001
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
show all

SCSI Primary Commands - 2.pdf

Create successful ePaper yourself

Delete template?

Save as template?