SCSI Primary Commands - 2.pdf

More documents

Recommendations

Info

T10/1236-D Revision 20 18 July 2001If the logical unit inventory changes for any reason, including completion of initialization, removal of a logical unit, orcreation of a logical unit, the device server shall generate a unit attention command for all initiators (see SAM-2).The device server shall set the additional sense code to REPORTED LUNS DATA HAS CHANGED.The execution of a REPORT LUNS command to any valid and installed logical unit shall clear the REPORTEDLUNS DATA HAS CHANGED unit attention condition for all logical units of that target with respect to the requestinginitiator. A valid and installed logical unit is one having a PERIPHERAL QUALIFIER of 000b in the standard INQUIRYdata (see 7.3.2).The device server shall report those devices in the logical unit inventory using the format shown in table 100.Table 100 — REPORT LUNS parameter list formatBitByte7 6 5 4 3 2 1 00 (MSB)LUN LIST LENGTH (N-7)3 (LSB)4 (MSB)Reserved7 (LSB)LUN list8 (MSB)First LUN15 (LSB)...n-7 (MSB)Last LUNn(LSB)The LUN LIST LENGTH field shall contain the length in bytes of the LUN list that is available to be transferred. TheLUN list length is the number of logical unit numbers in the logical unit inventory multiplied by eight. If the allocationlength in the CDB is too small to transfer information about the entire logical unit inventory, the LUN list length valueshall not be adjusted to reflect the truncation.134 dpANS SCSI Primary Commands - 2 (SPC-2)
18 July 2001 T10/1236-D Revision 207.20 REQUEST SENSE command7.20.1 REQUEST SENSE command introductionThe REQUEST SENSE command (see table 101) requests that the device server transfer sense data to the applicationclient.Table 101 — REQUEST SENSE commandBitByte7 6 5 4 3 2 1 00 OPERATION CODE (03h)1 Reserved2 Reserved3 Reserved4 ALLOCATION LENGTH5 CONTROLSense data shall be available and cleared under the conditions defined in SAM-2. If the device server has no othersense data available to return, it shall return a sense key of NO SENSE and an additional sense code of NOADDITIONAL SENSE INFORMATION.If the device server is in the standby power condition or idle power condition when a REQUEST SENSE commandis received and there is no ACA or CA condition, the device server shall return a sense key of NO SENSE and anadditional sense code of LOW POWER CONDITION ON. On completion of the command the logical unit shallreturn to the same power condition that was active before the REQUEST SENSE command was received. AREQUEST SENSE command shall not reset any active power condition timers.The device server shall return CHECK CONDITION status for a REQUEST SENSE command only to reportexception conditions specific to the command itself. For example:a) An invalid field value is detected in the CDB;b) An unrecovered parity error is detected by the service delivery subsystem; orc) A target malfunction that prevents return of the sense data.If a recovered error occurs during the processing of the REQUEST SENSE command, the device server shallreturn the sense data with GOOD status. If a device server returns CHECK CONDITION status for a REQUESTSENSE command, the sense data may be invalid.NOTE 28 The sense data appropriate to the selection of an invalid logical unit is defined in SAM-2.Device servers shall be capable of returning eighteen bytes of data in response to a REQUEST SENSE command.If the allocation length is eighteen or greater, and a device server returns less than eighteen bytes of data, theapplication client should assume that the bytes not transferred would have been zeros had the device serverreturned those bytes. Application clients may determine how much sense data has been returned by examiningthe ALLOCATION LENGTH field in the CDB and the ADDITIONAL SENSE LENGTH field in the sense data. Device serversshall not adjust the additional sense length to reflect truncation if the allocation length is less than the sense dataavailable.dpANS SCSI Primary Commands - 2 (SPC-2) 135
Page 1 and 2:
dpANSProjectT10/1236-DRevision 2018
Page 3:
DraftANSI (r)NCITS.351:200xAmerican
Page 6 and 7:
T10/1236-D Revision 20 18 July 2001
Page 8 and 9:
Page 10 and 11:
Page 12 and 13:
Page 14 and 15:
Page 16 and 17:
Page 18 and 19:
Page 20 and 21:
Page 22 and 23:
Page 24 and 25:
Page 26 and 27:
Page 28 and 29:
Page 30 and 31:
Page 32 and 33:
Page 34 and 35:
Page 36 and 37:
Page 38 and 39:
Page 40 and 41:
Page 42 and 43:
Page 44 and 45:
Page 46 and 47:
Page 48 and 49:
Page 50 and 51:
Page 52 and 53:
Page 54 and 55:
Page 56 and 57:
Page 58 and 59:
Page 60 and 61:
Page 62 and 63:
Page 64 and 65:
Page 66 and 67:
Page 68 and 69:
Page 70 and 71:
Page 72 and 73:
Page 74 and 75:
Page 76 and 77:
Page 78 and 79:
Page 80 and 81:
Page 82 and 83:
Page 84 and 85:
Page 86 and 87:
Page 88 and 89:
Page 90 and 91:
Page 92 and 93:
Page 94 and 95:
Page 96 and 97:
Page 98 and 99:
Page 100 and 101:
Page 102 and 103: T10/1236-D Revision 20 18 July 2001
Page 202 and 203:
Page 204 and 205:
Page 206 and 207:
Page 208 and 209:
Page 210 and 211:
Page 212 and 213:
Page 214 and 215:
Page 216 and 217:
Page 218 and 219:
Page 220 and 221:
Page 222 and 223:
Page 224 and 225:
Page 226 and 227:
Page 228 and 229:
Page 230 and 231:
Page 232 and 233:
Page 234 and 235:
Page 236 and 237:
Page 238 and 239:
Page 240 and 241:
Page 242 and 243:
Page 244 and 245:
Page 246 and 247:
Page 248 and 249:
Page 250 and 251:
Page 252 and 253:
Page 254 and 255:
Page 256 and 257:
Page 258 and 259:
Page 260 and 261:
Page 262 and 263:
Page 264 and 265:
Page 266 and 267:
Page 268 and 269:
Page 270 and 271:
Page 272 and 273:
Page 274 and 275:
Page 276 and 277:
Page 278 and 279:
Page 280 and 281:
Page 282 and 283:
Page 284 and 285:
Page 286 and 287:
Page 288 and 289:
Page 290 and 291:
Page 292 and 293:
show all

SCSI Primary Commands - 2.pdf

Create successful ePaper yourself

Delete template?

Save as template?