EN / ACS800-31/U31 Hardware Manual - Simark Controls

More documents

Recommendations

Info

3AFE68599954 Rev A <strong>EN</strong>EFFECTIVE: 14.10.2005Dimensional drawings: 14.10.2005ABB OyAC DrivesP.O. Box 184FI-00381 HELSINKIFINLANDTelephone +358 10 22 11Fax +358 10 22 22681Internet http://www.abb.comABB Inc.Automation TechnologiesDrives & Motors16250 West Glendale DriveNew Berlin, WI 5<strong>31</strong>51USATelephone 262 785-3200800-HELP-365Fax 262 780-5135
Page 1 and 2:
ACS800Hardware ManualACS800-31 Driv
Page 3:
ACS800-31 Drives5.5 to 110 kWACS800
Page 6 and 7:
2NEW (page 31): Type codeThe table
Page 8 and 9:
4WARNING! The Safe torque off funct
Page 10 and 11:
6Circuit diagramThe diagram below s
Page 12 and 13:
8Update Notice
Page 14 and 15:
6Installation and maintenance workT
Page 16 and 17:
8Mechanical installation and mainte
Page 18 and 19:
10OperationThese warnings are inten
Page 20 and 21:
12Safety instructions
Page 22 and 23:
14Type code . . . . . . . . . . . .
Page 24 and 25:
16Motor control and I/O board (RMIO
Page 26 and 27:
18Materials . . . . . . . . . . . .
Page 28 and 29:
20ContentsThe chapters of this manu
Page 30 and 31:
22TaskCheck the insulation of the m
Page 32 and 33:
X41UDC+UDC-24I/OterminalsU1 V1 W1 U
Page 34 and 35:
26AC voltage and current waveformsT
Page 36 and 37:
28Main circuit and control interfac
Page 38 and 39:
30Connection diagram of the RMIO bo
Page 40 and 41:
32The ACS800-31/U31
Page 42 and 43:
34The type designation label is att
Page 44 and 45:
36Mounting the drive on the wallUni
Page 46 and 47:
38Unit above anotherLead the out-co
Page 48 and 49:
403. Check that the motor voltage r
Page 50:
42Requirements tableThe following t
Page 53 and 54:
45Supply connectionDisconnecting de
Page 55 and 56:
47Short-circuit protectionProtect t
Page 57 and 58:
49Ground fault protectionThe drive
Page 59 and 60:
51Selecting the power cablesGeneral
Page 61 and 62:
53Additional US requirementsType MC
Page 64 and 65:
56Selecting the control cablesAll c
Page 66 and 67:
58A diagram of the cable routing is
Page 68 and 69:
60IT (ungrounded) systemsIn units w
Page 70 and 71:
62Conductor stripping lengthsStrip
Page 72 and 73:
64Frame sizes R6: Cable lug install
Page 74 and 75:
66Wire size Compression lug Crimpin
Page 76 and 77:
68360 degrees groundingInsulation12
Page 78 and 79:
70Fastening the control cables and
Page 80 and 81:
72Connect the AGPS board as follows
Page 82 and 83:
74Dimensional drawingThe dimensiona
Page 84 and 85:
76Note on external power supplyExte
Page 86 and 87:
78External control connections (US)
Page 88 and 89:
80Relay outputsSwitching capacityMi
Page 90 and 91: 82Motor control and I/O board (RMIO
Page 92 and 93: 84Check...The motor connections at
Page 94 and 95: 86Control panelThe drive is equippe
Page 96 and 97: 88Start-up and use
Page 98 and 99: 90ParametersNo. Name/Value Descript
Page 100 and 101: 92No. Name/Value Description T./FbE
Page 102 and 103: 94Actual signals and parameters
Page 104 and 105: 96HeatsinkThe heatsink fins pick up
Page 106 and 107: 98Replacement (R6)Remove the top co
Page 108 and 109: 100Fault tracing
Page 110 and 111: 102IEC dataACS800-31 sizeRatingsThe
Page 112 and 113: 104Mains cable fusesFuses for short
Page 114 and 115: 106NEMA dataRatingsThe NEMA ratings
Page 116 and 117: 108Cable typesCable sizing is based
Page 118 and 119: 110Motor connectionVoltage (U 2 )Fr
Page 120 and 121: 112MaterialsDrive enclosure • PC/
Page 122 and 123: 114Second environment (drive of cat
Page 124 and 125: 116Second environment (drive of cat
Page 126 and 127: 118Technical data
Page 128 and 129: 120Frame size R5 (IP21, UL type ope
Page 130 and 131: 122Dimensional drawings
Page 132 and 133: 124External brake chopper and resis
Page 134 and 135: 126Brake circuit commissioningFor S
Page 136 and 137: 128Connecting +24 V external power
Page 138 and 139: 130RMIO board of the line-side conv
Page 140: 132External +24 V power supply for
show all

EN / ACS800-31/U31 Hardware Manual - Simark Controls

Create successful ePaper yourself

Delete template?

Save as template?