EN / ACS800-31/U31 Hardware Manual - Simark Controls

More documents

Recommendations

Info

6Circuit diagramThe diagram below shows the connection between the ASTO board and the drivewhen it is ready. For an example diagram of a complete Safe torque off circuit, seepage 3 (in this Update Notice).3AUA0000069101DimensionsThe dimensions of the ASTO board are the same as the dimensions of the AGPSboard. See Dimensional drawing on page 74.NEW (page 111): ASTO-11CNominal input voltage 24 V DCNominal input current 40 mA (20mA per channel)X1 terminal sizes 4 x 2.5 mm 2Nominal output current 0.4 AX2 terminal block type JST B4P-VHAmbient temperature 0...50°CRelative humidity Max. 90%, no condensation allowedDimensions (with 167 x 128 x 52 mm (Height x Weight x Depth)enclosure)Weight (with enclosure) 0.75 kgUpdate Notice
7NEW (page 111): Ambient conditionsModules with option +Q967: the installation site altitude in operation is 0 to 2000 m.Operationinstalled for stationary useInstallation site altitude [...]Modules with option +Q967: 0 to 2000 mUpdate Notice
Page 1 and 2: ACS800Hardware ManualACS800-31 Driv
Page 3: ACS800-31 Drives5.5 to 110 kWACS800
Page 6 and 7: 2NEW (page 31): Type codeThe table
Page 8 and 9: 4WARNING! The Safe torque off funct
Page 12 and 13: 8Update Notice
Page 14 and 15: 6Installation and maintenance workT
Page 16 and 17: 8Mechanical installation and mainte
Page 18 and 19: 10OperationThese warnings are inten
Page 20 and 21: 12Safety instructions
Page 22 and 23: 14Type code . . . . . . . . . . . .
Page 24 and 25: 16Motor control and I/O board (RMIO
Page 26 and 27: 18Materials . . . . . . . . . . . .
Page 28 and 29: 20ContentsThe chapters of this manu
Page 30 and 31: 22TaskCheck the insulation of the m
Page 32 and 33: X41UDC+UDC-24I/OterminalsU1 V1 W1 U
Page 34 and 35: 26AC voltage and current waveformsT
Page 36 and 37: 28Main circuit and control interfac
Page 38 and 39: 30Connection diagram of the RMIO bo
Page 40 and 41: 32The ACS800-31/U31
Page 42 and 43: 34The type designation label is att
Page 44 and 45: 36Mounting the drive on the wallUni
Page 46 and 47: 38Unit above anotherLead the out-co
Page 48 and 49: 403. Check that the motor voltage r
Page 50: 42Requirements tableThe following t
Page 53 and 54: 45Supply connectionDisconnecting de
Page 55 and 56: 47Short-circuit protectionProtect t
Page 57 and 58: 49Ground fault protectionThe drive
Page 59 and 60: 51Selecting the power cablesGeneral
Page 61 and 62:
53Additional US requirementsType MC
Page 64 and 65:
56Selecting the control cablesAll c
Page 66 and 67:
58A diagram of the cable routing is
Page 68 and 69:
60IT (ungrounded) systemsIn units w
Page 70 and 71:
62Conductor stripping lengthsStrip
Page 72 and 73:
64Frame sizes R6: Cable lug install
Page 74 and 75:
66Wire size Compression lug Crimpin
Page 76 and 77:
68360 degrees groundingInsulation12
Page 78 and 79:
70Fastening the control cables and
Page 80 and 81:
72Connect the AGPS board as follows
Page 82 and 83:
74Dimensional drawingThe dimensiona
Page 84 and 85:
76Note on external power supplyExte
Page 86 and 87:
78External control connections (US)
Page 88 and 89:
80Relay outputsSwitching capacityMi
Page 90 and 91:
82Motor control and I/O board (RMIO
Page 92 and 93:
84Check...The motor connections at
Page 94 and 95:
86Control panelThe drive is equippe
Page 96 and 97:
88Start-up and use
Page 98 and 99:
90ParametersNo. Name/Value Descript
Page 100 and 101:
92No. Name/Value Description T./FbE
Page 102 and 103:
94Actual signals and parameters
Page 104 and 105:
96HeatsinkThe heatsink fins pick up
Page 106 and 107:
98Replacement (R6)Remove the top co
Page 108 and 109:
100Fault tracing
Page 110 and 111:
102IEC dataACS800-31 sizeRatingsThe
Page 112 and 113:
104Mains cable fusesFuses for short
Page 114 and 115:
106NEMA dataRatingsThe NEMA ratings
Page 116 and 117:
108Cable typesCable sizing is based
Page 118 and 119:
110Motor connectionVoltage (U 2 )Fr
Page 120 and 121:
112MaterialsDrive enclosure • PC/
Page 122 and 123:
114Second environment (drive of cat
Page 124 and 125:
116Second environment (drive of cat
Page 126 and 127:
118Technical data
Page 128 and 129:
120Frame size R5 (IP21, UL type ope
Page 130 and 131:
122Dimensional drawings
Page 132 and 133:
124External brake chopper and resis
Page 134 and 135:
126Brake circuit commissioningFor S
Page 136 and 137:
128Connecting +24 V external power
Page 138 and 139:
130RMIO board of the line-side conv
Page 140:
132External +24 V power supply for
show all

EN / ACS800-31/U31 Hardware Manual - Simark Controls

Create successful ePaper yourself

Delete template?

Save as template?