GPS Connector - Triumph Instructions.com

EnglishFitting Instructions:Tiger 1050, Trophy and Trophy SEA9938122Thank you for choosing this Triumph genuine accessory kit. This accessory kit is the product of Triumph's use of provenengineering, exhaustive testing, and continuous striving for superior reliability, safety and performance.Completely read all of these instructions before commencing the installation of the accessory kit in order to becomethoroughly familiar with the kit’s features and the installation process.These instructions should be considered a permanent part of your accessory kit, and should remain with it even if youraccessory-equipped motorcycle is subsequently sold.12Parts Supplied:1. GPS connector 1 off 2. Cable ties 6 offPublication part number A9900103 issue 3, ADC 12671© Triumph Designs Ltd. 20131 of 3

WarningThis accessory kit is designed for use on TriumphTiger 1050, Trophy and Trophy SE motorcycles only andshould not be fitted to any other Triumph model or toany other manufacturer’s motorcycle. Fitting thisaccessory kit to any other Triumph model or to anyother manufacturer’s motorcycle will affect theperformance, stability and handling of the motorcycle.This may affect the rider’s ability to control themotorcycle and could cause an accident.Tiger 1050 only1. Disconnect the battery, as described in the ServiceManual.2. Remove the cockpit fairing, as described in theService Manual.3. Identify the 2-way connector on the main wiringharness (located centrally above the headlight) andremove the blanking plug.WarningAlways have Triumph approved parts, accessories andconversions fitted by a trained technician of anauthorised Triumph dealer. The fitment of parts,accessories and conversions by a technician who is notof an authorised Triumph dealer may affect thehandling, stability or other aspects of the motorcycle’soperation which may result in loss of motorcycle controland an accident.21WarningAlways ensure that the newly installed wiring does notchafe against other parts of the motorcycle such that itmay be rubbed through and cause an electricalproblem. In addition, always ensure that the newlyinstalled wiring will not restrict steering movement. Bothconditions are hazardous and could give rise to adangerous riding condition resulting in a fire, loss ofmotorcycle control and an accident.WarningThroughout this operation, ensure that the motorcycle isstabilised and adequately supported to prevent risk ofinjury from the motorcycle falling.WarningA torque wrench of known accurate calibration must beused when fitting this accessory kit. Failure to tightenany of the fasteners to the correct torque specificationmay affect motorcycle performance, handling andstability. This may result in loss of motorcycle control andan accident.cefb1. GPS connector (Tiger 1050 shown)2. Blanking plug4. Connect the GPS connector to the 2-way connector.Trophy and Trophy SE onlyInstallation instructions for the GPS connector lead can befound in the instructions supplied with the GPS MountKits A9828009 and A9828011.All ModelsNote:• Retain the 2-way connector blanking plug foruse if the motorcycle is returned to originalcondition.Note:• The GPS connector red lead is the positive (+)connection, the GPS connector black lead is thenegative (-) connection.CautionIncorrect connection of the positive and negative leadswill result in permanent damage to the GPS unit. Alwaysconnect the GPS unit following the GPS systemmanufacturer’s instructions.5. Identify the positive and negative leads for the GPSsystem, following the GPS system manufacturer’sinstructions.2 of 3

6. Ensuring the GPS system positive and negative leadsare connected to the correct leads of the GPSconnector, secure the connections as follows:7. Strip approximately 6 mm of insulation from theends of the GPS system’s leads.8. Using an appropriate crimping tool, secure the endof the GPS system’s leads into the pink crimpconnectors which are attached to the GPS connectorharness.9. Check the security of both connections by gentlypulling on both sides of the join. Re-crimp ifnecessary.WarningThe air from a heat gun and the heat gun itself are veryhot. Wear suitable protective gloves and do not pointthe heat gun at any part of your body as serious burnsto the skin may result.CautionWhen shrinking the pink coloured sleeves, take care notto burn any part of the wiring harness or seriousdamage will result to the cable. Excessive heat will alsocause the tubing to become brittle rendering it useless.10. Use a heat gun to shrink the pink coloured sleevesaround both joints. When the sleeves are fullyshrunk, allow to cool before taping over each sleevewith black electrical insulation tape. Ensure that thetaping extends past each side of the sleeves by atleast 15 mm.Tiger 1050 only11. Secure the GPS connector to the instrument supportsub-frame using the cable ties supplied, ensuringthat the steering mechanism is not hampered andthat the cable cannot be trapped or stretched.12. Refit the cockpit fairing, as described in the relevantService Manual.WarningEnsure that steering movement is not restricted byturning the handlebars through their full range ofmovement while checking that they move freely fromleft to right.13. Reconnect the battery, positive (red) lead first, asdescribed in the relevant Service Manual.WarningIf, after fitting this accessory kit, you have any doubtabout the performance of any aspect of the motorcycle,contact an authorised Triumph dealer and do not ridethe motorcycle until the authorised dealer has declaredit fit for use. Riding a motorcycle when there is anydoubt as to any aspect of the performance of themotorcycle may result in loss of control of themotorcycle leading to an accident.WarningWhen fitting and connecting the GPS connector, routethe cables to follow existing harnesses where possibleand ensure no cables can be trapped or stretched bythe steering mechanism.3 of 3