100+ page pdf - University of Iowa Hospitals and Clinics

More documents

Recommendations

Info

Rev. 9 December 15, 2012SECTION 07550MODIFIED BITUMEN MEMBRANE ROOFING (SBS)1.06 QUALIFICATIONSA. Applicator:1. Company specializing in performing the work of this section with a minimum of five(5) years documented experience.2. Company certified by the membrane manufacturer for a minimum of three (3) years asan approved applicator of the products specified in this section.3. Company having workmen trained by the membrane manufacturer. These trainedworkmen shall perform the work.1.07 DELIVERY, STORAGE AND HANDLINGA. Deliver and store materials under provisions of Section 01610.B. Deliver materials in sufficient quantity to allow continuity of work.C. Coordinate delivery of materials with Owner so that minimal interruption of Owner'soperations occurs.D. Materials shall be stored in their original, tightly sealed containers or unopened packages, andshall be clearly labeled with the manufacturer's brand name and such identifying referencenumbers as are appropriate. Deliver materials to job site on pallets. Do not stack pallets.E. Materials shall be stored in a neat, safe manner, so as not to exceed allowable live load of thestorage area. Contractor shall not load pallets of material onto the roof deck without approvalfrom the Architect/Engineer prior to loading. Disperse materials on roof deck to avoidconcentrated loading.F. Store materials in dry, protected areas in an upright position. Control temperature of storageareas in accordance with manufacturer's instruction. Protect materials from freezing.G. Follow manufacturer's guidelines for required temperatures of material prior to application.H. Any materials damaged in handling or storage are not to be used.I. The Contractor shall assume full responsibility for the protection and safekeeping of materialsstored on Owner's premises.J. Store roll goods on ends only. Discard rolls which have been flattened, creased, or otherwisedamaged.K. Remove wet material from project site.L. Comply with fire and safety regulations.Modified Bitumen Membrane Roofing (SBS)UIHC #20X-0XX 07550-4
Rev. 9 December 15, 20121.08 JOB CONDITIONSSECTION 07550MODIFIED BITUMEN MEMBRANE ROOFING (SBS)A. Apply roofing in dry weather.B. If the newly constructed roof or existing insulation becomes wet due to rainstorms, faultywater cutoffs, or other reasons, the Contractor shall remove and dispose of all wet materials,dry the affected roof area, and reconstruct the roof in accordance with these specifications atno cost to the Owner.C. Coal tar base, oil base, or plastic roof cements are not to be used in direct contact with steamor steam source.D. All bonding, splicing and sealing surfaces must be free of dirt, moisture and any othercontaminants.E. The roof surface shall be free of ponded water, ice, snow, or algae prior to installing the newroof system.F. Do not apply roofing unless correct asphalt application temperatures can be maintained toobtain good embedment and adhesion. Follow manufacturer's and NRCA's guidelines forbitumen application temperatures. Maintain proper Equiviscous Temperature (EVT) at pointof application.G. Ensure roof deck is structurally sound to support construction traffic. Notify Owner orArchitect/Engineer immediately of any conditions that are not structurally sound.1.09 WARRANTYA. Provide warranty and guarantee under provisions of Section 01780.B. On new roofing systems provide to the Owner the membrane manufacturer's 20 year no-dollarlimit material and workmanship warranty the date of final acceptance by the Owner.Warranties shall cover, but not be limited to, the following:1. Deterioration of the roofing membrane or flashing system resulting from ordinarywear and tear by the elements.2. Workmanship on the part of the approved roofing contractor in the application of theHigh-Performance Roofing System.3. Splits or breaks in the High-Performance Membrane not caused by structuralmovement or failure or movement of any material underlying the roofing membraneor base flashing.4. Blisters, wrinkles, ridges, fishmouths or open laps in the High-PerformanceMembrane.5. Slippage of the High-Performance Membrane or base flashing.Modified Bitumen Membrane Roofing (SBS)UIHC #20X-0XX 07550-5
Page 1 and 2:
Architectural and EngineeringDesign
Page 3:
Rev. 9 December 15, 2012Rev. 9 Dece
Page 11 and 12:
Page 13 and 14:
Page 15 and 16:
Page 17 and 18:
Page 19 and 20:
Page 21 and 22:
Page 23 and 24:
Page 25 and 26:
Page 27 and 28:
Page 29 and 30:
Page 31 and 32:
Page 33 and 34:
Page 35 and 36:
Page 37 and 38:
Page 39 and 40:
Page 41 and 42:
Page 43 and 44:
Page 45 and 46:
Page 47 and 48:
Page 49 and 50:
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
Page 65 and 66:
Page 67 and 68:
Page 69 and 70:
Page 71 and 72:
Page 73 and 74:
Page 75 and 76:
Page 77 and 78: Rev. 9 December 15, 2012Rev. 9 Dece
Page 101 and 102: Rev. 9 December 15, 2012APPENDIX AS
Page 103 and 104: APPENDIX Rev. 9BDecember 15, 2012DE
Page 105 and 106: Rev. 9 December 15, 2012APPENDIX CC
Page 107 and 108: Rev. 9 December 15, 2012APPENDIX DU
Page 109 and 110: Rev. 9 December 15, 2012Systems Man
Page 111 and 112: Rev. 9 December 15, 2012NAME OF PRO
Page 125 and 126: Rev. 9 December 15, 2012SECTION 075
Page 127: Rev. 9 December 15, 2012SECTION 075
Page 141: Rev. 9 December 15, 2012ROOF MEMBRA
Page 152 and 153: Rev. 9 December 15, 2012APPENDIX HU
Page 154 and 155: Rev. 9 December 15, 2012Cooling sha
Page 156 and 157: Rev. 9 December 15, 20127) Low batt
Page 158 and 159: Rev. 9 December 15, 2012b) Ammeter
Page 160 and 161: Rev. 9 December 15, 2012(3) Space v
Page 162 and 163: Rev. 9 December 15, 20123. Torsiona
Page 164 and 165: Rev. 9 December 15, 2012b. Alternat
Page 166 and 167: Rev. 9 December 12, 2012Addressable
Page 168 and 169: Rev. 9 December 12, 2012Wire Manufa
Page 170 and 171: Rev. 9 December 15, 2012Appendix KA
Page 172 and 173: Rev. 9 December 15, 2012Division Se
Page 178 and 179:
Rev. 9 December 15, 2012Division Se
Page 180 and 181:
Page 182 and 183:
Page 184 and 185:
Rev. 9 December 15, 2012APPENDIX LM
Page 186 and 187:
Rev. 9 December 15, 201234567891011
Page 188 and 189:
Rev. 9 December 15, 2012Drawing Num
Page 190 and 191:
Rev. 9 December 15, 2012Typical App
Page 192 and 193:
Page 194 and 195:
Rev. 9 December 15, 2012Typical app
Page 196 and 197:
Page 198 and 199:
Page 200 and 201:
Rev. 9 December 15, 2012StructureCe
Page 202 and 203:
Rev. 9 December 15, 2012StructureCe
Page 204 and 205:
Page 206 and 207:
Rev. 9 December 15, 2012By Others (
Page 208 and 209:
Page 210 and 211:
show all

100+ page pdf - University of Iowa Hospitals and Clinics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?