Series 8650A Universal Power Meters - Giga-tronics

More documents

Recommendations

Info

Series 8650A Universal Power Meters3.1.5 Setting the Calibrator LevelTo set the calibrator power, an HP432 power meter with an HP8478B thermistor is placed at thecalibrator output. The 432 output is monitored with a DVM connected to a computer system. The 25dB pad is switched out. The 50 MHz oscillator is turned on and the 50 MHz amplifiers are powered up.As the RF power is applied to the thermistor, integrator U10D starts to decrease the DC power to thethermistor. Integrator U11 senses the error voltage and decreases the gain of the oscillator bufferamplifier. The actual output power reading is sent to the instrument microprocessor which adjusts theDAC until there is exactly 1.000 mW at the calibrator output as measured by the HP432/8478 powermeter.The data that was written to the DAC, to get 1.000 mW, is stored permanently in the EEPROM. Thissets the accuracy of the 1.000 mW reference. While the HP8478 thermistor is on the calibrator output,it also sets the 1.000 mW reference for 1 GHz. The A-D value is also stored in the EEPROM.3.1.6 Calibrating the Sensor/Meter CombinationThe sensor is connected to the calibrator output. There is +3.00 dBm going to the detector in thesensor. The 8650 meter measures the detector voltage and temporarily stores it. The 6.25 dB pad isswitched out. The microprocessor increases the DC power in the thermistor until the diode detector inthe sensor provides the same voltage as the temporarily stored value. The microprocessor calculates thenew DC power from the new DAC value. The difference between the new and the old DC power is thechange in RF power. 10 Log (P RFO /P RFN ) is the value of the pad. The accuracy is independent of thedetector diode because it is only used at one level. The accuracy is only dependant upon the linearity ofthe DAC and the 0.1 % resistors. The accuracy is much better than 0.01 dB. The other two pads aremeasured in a similar manner.During the three attenuator measurements, the detector voltage is measured every 6.25 dB from +20 to–30 dBm. Then the calibrator is stepped in 1.000 dB steps. This data is used to correct the diode nonlinearityduring normal meter usage. In effect, the detector is now calibrated.3-4 Manual 32089, Rev. A, December 2000
4Replaceable Parts4.1 8650A Replaceable PartsTable 4-1 is a list of assemblies that are available through Giga-tronics.☛NOTE: Due to the nature of the surface mount construction of the 8650A series powermeters, discrete components are not called out. It is assumed that the average field repairfacility will not have the ability to replace Surface Mount Parts.Table 4-1: 8650A List of AssembliesNomenclaturePart NumberCover Assembly 31395Chassis Cover 31396Cover Base Pan 31397Front FeetRear FeetGround StripHFFB-00001HFFB-00002GGS0-00007Front Bezel Subassembly 31391Detector Input Assembly (single channel) 31383Detector Input Assembly (dual channel) 31393Front Panel Board 31351Front Bezel 31400Keypad 31404LCD Display Module 32053Calibrator 31394Signal Processor Board (Dual Channel) 31371Signal Processor Board (Single Channel) 31373Digital (Host) Board 31356Manual 32089, Rev. A, December 2000 4-1
Page 2 and 3: All technical data and specificatio
Page 4 and 5: Preparation for ReshipmentFollow th
Page 6 and 7: Series 8650A Universal Power Meters
Page 33 and 34: Adjustments & Performance Tests2.3.
Page 35 and 36: Adjustments & Performance Tests2.4
Page 37 and 38: Adjustments & Performance Tests2.5.
Page 39 and 40: 3Theory of Operation13.1 8650A Powe
Page 41: Theory of Operation3.1.4 Calibrator
Page 45 and 46: 5Troubleshooting5.1 8650A Fault Iso
Page 47 and 48: TroubleshootingSensor will notcalib
Page 49 and 50: TroubleshootingCrest factor errorsN
Page 51 and 52: TroubleshootingNotes:1. The instrum
Page 53 and 54: Troubleshooting5.2.3 Calibrator1. U
Page 55: IndexSeries 8650A Universal Power M

Series 8650A Universal Power Meters - Giga-tronics

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?