2. installation procedure for optional equipment - toshiba tec europe
2. installation procedure for optional equipment - toshiba tec europe 2. installation procedure for optional equipment - toshiba tec europe
EO18-12010Page8. MAIN UNIT REPLACEMENT ..................................................................................... 8- 18.1 Operator’s Display Section ..............................................................................................8- 18.2 Bottom Cover Section......................................................................................................8- 79. APPENDIX.................................................................................................................. 9- 19.1 Serial Interface COM1 to COM6......................................................................................9- 19.2 VGA Connector ...............................................................................................................9- 29.3 DRW1, DRW2 (Cash Drawer 24V Type).........................................................................9- 29.4 LAN..................................................................................................................................9- 29.5 USB .................................................................................................................................9- 39.6 PS/2 (Keyboard, Mouse) .................................................................................................9- 39.7 24V OUT Connector ........................................................................................................9- 39.8 LINEOUT .........................................................................................................................9- 39.9 MIC ..................................................................................................................................9- 39.10 LVDS1 Connector............................................................................................................9- 49.11 Parallel (LPT) Connector .................................................................................................9- 49.12 Powered USB (24V) Connector.......................................................................................9- 59.13 Powered USB (12V) Connector.......................................................................................9- 5NOTE: Pictures in this manual show that body colour may differ from that of the original.CAUTION!1. This manual may not be copied in whole or in part without prior written permission of TOSHIBATEC.2. The contents of this manual may be changed without notification.3. Please refer to your local Authorised Service representative with regard to any queries youmay have in this manual.Copyright © 2005by TOSHIBA TEC CORPORATIONAll Rights Reserved570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
1. UNPACKING EO18-120101.1 Procedure1. UNPACKING1.1 Procedure1) Open the carton.2) Take the accessories out of the carton.3) Take out the POS terminal, then remove the pads.4) Place the POS terminal on a level surface.Ferrite Core (1 pc.)Bind Screw M-3x3(8 pcs.)CartonPadST-71 POS TerminalPadCarton1.2 Checks1) Check for the damage or scratches on the machine.2) Confirm that none of the accessories are missing.Detailed information of each accessory is as shown below.Accessory Quantity UsageBind Screw M-3x3 8 Used to secure the Hard Disk Drive (HDD) to the HDDHolder.Ferrite Core 1 Attached to the cable when using the option HS-530 HandyScanner.Owner’s Manual 11- 1
- Page 1 and 2: TEC POS TerminalST-71 SERIESMainten
- Page 3: EO18-12010(Revision Date: Jan. 30,
- Page 7 and 8: 2. INSTALLATION PROCEDURE FOR OPTIO
- Page 9 and 10: 2. INSTALLATION PROCEDURE FOR OPTIO
- Page 11 and 12: 2. INSTALLATION PROCEDURE FOR OPTIO
- Page 13 and 14: 2. INSTALLATION PROCEDURE FOR OPTIO
- Page 15 and 16: 2. INSTALLATION PROCEDURE FOR OPTIO
- Page 17 and 18: 2. INSTALLATION PROCEDURE FOR OPTIO
- Page 19 and 20: 2. INSTALLATION PROCEDURE FOR OPTIO
- Page 21 and 22: 2. INSTALLATION PROCEDURE FOR OPTIO
- Page 23 and 24: 2. INSTALLATION PROCEDURE FOR OPTIO
EO18-12010Page8. MAIN UNIT REPLACEMENT ..................................................................................... 8- 18.1 Operator’s Display Section ..............................................................................................8- 18.2 Bottom Cover Section......................................................................................................8- 79. APPENDIX.................................................................................................................. 9- 19.1 Serial Interface COM1 to COM6......................................................................................9- 19.2 VGA Connector ...............................................................................................................9- 29.3 DRW1, DRW2 (Cash Drawer 24V Type).........................................................................9- 29.4 LAN..................................................................................................................................9- 29.5 USB .................................................................................................................................9- 39.6 PS/2 (Keyboard, Mouse) .................................................................................................9- 39.7 24V OUT Connector ........................................................................................................9- 39.8 LINEOUT .........................................................................................................................9- 39.9 MIC ..................................................................................................................................9- 39.10 LVDS1 Connector............................................................................................................9- 49.11 Parallel (LPT) Connector .................................................................................................9- 49.12 Powered USB (24V) Connector.......................................................................................9- 59.13 Powered USB (12V) Connector.......................................................................................9- 5NOTE: Pictures in this manual show that body colour may differ from that of the original.CAUTION!1. This manual may not be copied in whole or in part without prior written permission of TOSHIBATEC.<strong>2.</strong> The contents of this manual may be changed without notification.3. Please refer to your local Authorised Service representative with regard to any queries youmay have in this manual.Copyright © 2005by TOSHIBA TEC CORPORATIONAll Rights Reserved570 Ohito, Izunokuni-shi, Shizuoka-ken, JAPAN
Change language