Classic Stand Fan - Casablanca Fan

TABLE OF CONTENTSIntroduction ............................................................. 3Safety and Warnings ................................................ 3Grounding ............................................................... 5Fused Plug ............................................................... 6Unpacking ............................................................... 7Base Assembly ......................................................... 7Motor Assembly ....................................................... 8Grill Assembly ......................................................... 9Operation.............................................................. 11Off / Speed Selection 11Oscillation11Adjustment11Maintenance .......................................................... 12Technical Support ................................................... 13Warranty ............................................................... 13Products ................................................................ 152

INTRODUCTIONThank you for choosing the Hunter Oscillating StandFan. This manual gives you complete instructions forassembling and using your fan. Here are some thefeatures you will enjoy with your fan:33An attractive design that enhances any decor33A powerful motor for maximum air flow33Three speeds to adjust your comfort level33All metal construction33Parts of this fan, including the blades and the grill,have been treated with Hunter’s Dust Armor Protection,making them less likely to attract dust and dirt.SAFETY AND WARNINGSTo reduce the risk of fire or electrical shock, DO NOT usethis fan with any solid-state speed control device.When using electrical appliances, basic precautionsshould always be taken to reduce the risk of fire, electricshock and personal injury:Read all instructions before using this fan.1. Improper installation may result in the risk of fire,electric shock or personal injury.2. To prevent the risk of fire and electric shock, DONOT use the unit near windows. Rain and moisturemay create an electrical hazard.3. The power plug must be removed from the powersocket when not in use, before cleaning, servicing,maintenance and before moving to another location.4. DO NOT put fan in a damp place or where humidityis high, such as a bathroom.5. The fan should be placed on a flat, stable surface toavoid overturning.6. Use fan only for intended use, as described in thisinstruction manual.7. To protect against electrical shock, DO NOT immerseany part of the unit in water or spray with liquids.3

8. Close supervision is necessary when any applianceis used near children.9. NEVER insert fingers, pencils or any other objectsthrough the grill when the fan is running.10. DO NOT operate any appliance with a damagedcord or plug, after the appliance malfunctions or hasbeen dropped or damaged in any manner.11. To disconnect, grip plug and pull from wall outlet.NEVER yank on cord.12. ALWAYS use on a dry surface.13. This product is intended for household use only andnot for commercial or industrial use.14. DO NOT operate fan in the presence of explosiveand/or flammable fumes.15. DO NOT place fan or any parts near an open flame,cooking or any other heating appliances.16. DO NOT use near curtains, plants, windowtreatments, etc.17. This appliance has a grounded three-prong plugand is suitable for grounded receptacle use only.An adapter is available for connecting three-bladegrounding-type plugs to two-slot receptacles. Theadapter must be properly grounded. DO NOTattempt to defeat the purpose of this safely feature.18. The rubber feet on this product may interact withwood and cause damage to furniture. Do not placeon fine wood furniture.4

GROUNDINGThis appliance is for household use only and may beplugged into any 120-volt AC electrical outlet (ordinaryhousehold current). DO NOT use any other type of outlet.WARNINGThis unit is suitable for grounded receptacle use only.GroundedPlugGrounding PinGrounded OutletBox CoverThe power cord has a grounded plug as shown inFigure 1, and must be used with an electrical outlet thatcan accommodate the grounding pin. If your electricaloutlet can not accommodate the grounding pin, then youmust purchase and install one of the two types of adaptersshown in Figure 2.AdapterMetalScrewFigure 1NOTE: The adapters ARE NOT supplied with this fan.Read, follow, and save the instructions that are includedwith the adapter you choose. Do not use an adapter ifyour electrical outlet can accommodate the grounding pin.LINE CORD SAFETY TIPSGroundingMeansGrounded OutletBox CoverFigure 21. NEVER pull or yank on the cord or the appliance.2. To insert plug, grasp it firmly and guide it into the outlet.3. To disconnect the appliance, grasp the plug andremove it from the outlet.4. Before each use, inspect the line cord for cuts and/or abrasion marks. If any are found, the applianceshould be serviced and the line cord replaced. Pleasereturn it to our Service Department or to an authorizedservice representative.5. NEVER wrap the cord tightly around theappliance, as this could place undue stress on thecord where it enters the appliance and could causeit to fray and break.6. DO NOT operate appliance if the line cord shows anydamage, if the appliance works intermittently or stopsworking entirely.5

FUSED PLUGThis plug is a safety feature. It contains a safety device(fuse) that should not be removed. Discard product if theattachment plug is damaged. To reduce the risk of fire,electric shock and personal injury, DO NOT remove,replace, repair or tamper with the originally suppliedplug. If the Fan does not function properly, it may be dueto the safety device incorporated in this plug.If the fuse fails, it is generally due to a short circuit orcircuit overload. Replace the fuse as per the instructionsbelow. If the replacement fuse fails, immediatelyunplug the unit and contact our technical supportdepartment for assistance.Figure 3Fuse Replacement:1. To replace the fuse, first turn the unit it off and unplugit from the wall. Locate the door on top of the plug.Figure 3.2. Slide the door on top of the plug towards the blades.Figure 4.Figure 43. Carefully remove the fuse from the clips holding it onthe top and bottom. Figure 5.Warning! Electrical Hazard! Only replace with afuse type and rating matching what was removed fromthe product.4. Gently push the fuse back into the pins that will holdit in place.Note: If the fuse is not seated properly, the unit will notfunction.Figure 55. Slide the Door back over the fuse box in the plug.6. Plug the fan back in and resume use.6

UNPACKINGAs you unpack the fan, save the carton and packingmaterials in case you want to move or ship the unit in thefuture. Carefully remove all items from the box.NOTE: It is best to have someone hold the box whileyou lift the fan and the protective packaging out of thecarton. Make sure all shipping materials are removedfrom fan before operating.HeightAdjustmentKnobBase TrimRingTelescopingPoleBASE ASSEMBLY1. Remove and height adjustment knob from telescopingpole by turning it counter clockwise. Also remove thecord clamp. Slide the base trim ring onto the pole.Reinstall the height adjustment knob and cord clamp.Figure 6.2. Remove the L-shaped screw from the telescopingpole by turning it counter clockwise. Figure 7.3. Insert the telescoping pole into the top of the base.Install the L-shaped screw into the threaded hole inthe bottom of the pole to secure the pole to the base.Figure 7.4. Tip the base back upright.5. Grasp the telescoping pole firmly and twist theadjustment knob counter clockwise to loosen. Figure 9.6. Raise the inner pole to maximum height and tightenthe adjustment knob by twisting clockwise untilsecure. Figure 9.TelescopingPoleBaseL-shapedScrewScrewFigure 6Figure 7Figure 8Inner PoleAdjustmentKnob7Figure 9

ATTACHING ASSEMBLY TO POLE1. Press the clip buttons in completely while sliding thepole from the motor housing assembly into the innerpole until the clip buttons appear through the hole inthe inner pole. Figure 10.Clip ButtonFigure 108

GRILL ASSEMBLYNote: The trim ring may be attached to the front and reargrills for shipping purposes. If so, remove the trim ring byloosening the trim ring screw.1. Remove the four grill mounting screws from themotor housing. Figure 11.2. Make sure that the grill is positioned so that threeof the grill lines are completely between the toptabs. Then place the Back Grill against the MotorHousing, Figure 12., and line up the four tabs onthe back of the grill to the four screw holes on thefront of the motor.3. To attach the Back Grill to the Motor Housingpartially install the four grill mounting screws.Tighten all four screws. Figure 13.Note: One of the grill mounting screws will have a starwasher on it, for grounding purposes. The other 3 screwswill not have a washer.4. Loosen the screw on the back of the Blade assembly.Figure 14a. Slide the Blade assembly onto themotor shaft. Figure 14.GrillMountingScrewGrill Lines1 2 3Top TabsFigure 11Figure 125. Tighten the Screw on the Blade assembly to secure itto the Motor. Make sure that the end of the screw ispositioned within the notch on the shaft. Figure 15.Caution: Ensure when tightening the screw on the backof the fan blade, you tighten it on the flat part of themotor shaft.14aFan BladeNotchFigure 13MotorFigure 14 Figure 159

GRILL ASSEMBLY (CONT.)6. Remove the grill ring from the front grill by looseningthe screw holding it.7. Place the front grill against the back grill so that theHunter logo faces right side up and push together untilthe tabs on the grills hold them together. Figure 16.8. Expand the grill ring by loosening the screw thatsecures it. Figure 17.9. Slide the grill ring over both front and back grillsturning the ring so that the screw that secures it, ison the bottom. Figure 17.10. Tighten the screw to secure the grill ring over boththe front and back grill. Figure 18.11. Straighten the cord from the motor housing alongthe telescoping pole and snap the cord clip over thecord onto the pole so that the cord rests in the notchon the clip. Figure 19.Back GrillHunter LogoFront GrillFigure 16ScrewGrillRingFigure 17ScrewCordFigure 18Cord Clip10NotchFigure 19

OPERATIONOff / Speed SelectionTo turn the fan on and off or to control the speed, turn thespeed knob on the top of the motor housing to the propersetting. Figure 20.HighMediumLowOffOscillationTo allow the fan to oscillate, push the knob beside the fanspeed control down. Pull up on the knob if oscillation isnot desired. Figure 21.Figure 20OscillationKnobFigure 2111

MAINTENANCEThis fan is permanently lubricated and will not requireadditional lubrication (oil) for the life of the fan.This fan requires little maintenance and containsno user serviceable parts. DO NOT try to fixit yourself. Contact qualified service personnelif servicing is needed.Before cleaning, turn fan off and unplug from electricaloutlet. Wipe off excess dust with a lintfree cloth. To ensureadequate air circulation to the motor, keep vents locatedat the rear of the motor free from dust accumulation. Avacuum cleaner hose can be used to clean these vents.DO NOT immerse the fan in water or any other liquid.CLEANING THE GRILL AND BLADE:1. Turn the fan off and unplug from the electrical outlet.2. Disassemble the grills by loosening the screw holdingthe grill ring and remove it from the grills.3. Two tabs hold the front grill and back grill together.Pull the front grill from the back.4. The blade may be removed by loosening the screwholding it in place. Grills and blades may be cleanedwith mild soap and water only after they have beenremoved from the motor housing.5. Use a dry or slightly damp lint free cloth to cleanthe fan. Do not use a furniture polish or any othercleaners that leave any residue, as they will damagethe protective Dust Armor.33Use a soft, slightly damp cloth to wipe the remainingfan parts.33DO NOT allow water or any other liquid to get intothe motor housing or base.33Reassemble the fan after blades and grills havedried completely.3 3 DO NOT plug the fan into an electrical outlet until ithas been fully reassembled.12

1. Problem33Fan will not oscillate.TROUBLESHOOTINGSolution33Push down on the knob on top of motor housing toactivate oscillation.TECHNICAL SUPPORTIf you have any additional questions or problems withyour Hunter Portable Fan, please call:USA: 1-888-830-1326Canada: 1-866-268-1936Hours of operation are from 7:00 am to 7:00 pmMonday - Friday and 8:00 am to 5:00 pm on Saturday,Central Time. You may also contact us on the Internet atwww.HunterFan.com.WARRANTYThe Hunter Fan Company makes the following limitedwarranty to the user or consumer purchaser of this HunterPortable Fan:If your Hunter Portable Fan motor fails at any timewithin one year after the date of sale due to a defect inmaterial or workmanship, labor to repair the defect willbe provided free of charge at our nearest service centeror our Service Department in Memphis, Tennessee. Youwill be responsible for labor costs after this one-yearperiod. The foregoing limited warranty applies only tothe motor itself, and does not apply to electronic controlssuch as remote controls, remote control receivers ortransmitters used in conjunction with the motor. Theseelectronic control items are included in the one yearlimited warranty below.WarrantyIf any part of your Hunter Portable Fan other than themotor fails at any time within one year after the date of13

sale due to a defect in material or workmanship, wewill repair or, at our option, replace the defective partfree of charge for parts and labor performed at ournearest service center or at our Service Department inMemphis, Tennessee.WarrantyIF THE USER OR CONSUMER PURCHASER CEASES TOOWN THE FAN, THIS WARRANTY AND ANY IMPLIEDWARRANTY WHICH THEN REMAINS IN EFFECT,INCLUDING BUT NOT LIMITED TO ANY IMPLIEDWARRANTY OF MERCHANTABILITY OR FITNESS FOR APARTICULAR PURPOSE, ARE VOIDED. NO WARRANTY,EXPRESSED OR IMPLIED, INCLUDING ANY WARRANTYOF MERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE, IS MADE IN RESPECT TO THE GLASS GLOBESOR LIGHT BULBS OR THE FINISH ON ANY METALPORTION OF THE FAN. THIS WARRANTY IS IN LIEUOF ALL OTHER EXPRESS WARRANTIES. THE DURATIONOF ANY IMPLIED WARRANTY, INCLUDING, BUTNOT LIMITED TO ANY IMPLIED WARRANTY OFMERCHANTABILITY OR FITNESS FOR A PARTICULARPURPOSE, IN RESPECT TO ANY HUNTER FAN MOTOROR OTHER FAN PART, IS EXPRESSLY LIMITED TO THEPERIOD OF THE EXPRESS WARRANTY SET FORTHABOVE FOR SUCH MOTORS AND OTHER PARTS.This warranty is voided if your Hunter Fan is notpurchased and used in the USA.This warranty excludes and does not cover defects,malfunctions or failures of any Hunter Portable fanwhich were caused by repairs by persons not authorizedby us, use of parts or accessories not authorized byus, mishandling, improper installation, modifications,or damage to the Hunter Portable fan while in yourpossession, or unreasonable use, including failure toprovide reasonable and necessary maintenance.To obtain servicing, contact the nearest Hunterauthorized service center or the Hunter Fan CompanyService Department, 7130 Goodlett Farms Pkwy. Suite400, Memphis, Tennessee 38016. Please contact usbefore shipping your fan to us. If we authorize you toship it to us, you will be responsible for all insuranceand freight or other transportation charges to our factoryservice center. We will return your Hunter Fan freightprepaid. Your portable fan should be properly packed toavoid damage in transit since we will not be responsible14