Hubbell Wiring Device.pdf - Eversave Technology

Technical Information Kellems ® Wire Management ProductsKellems ® Wire Management ProductsTechnical InformationStrain Relief GripsEDA(Overall)FB Ref.C (N.P.T. Thread Depth)Dimensions shown are approximate andare subject to change without notice.Deluxe Cord Grips Fitting DimensionsFemale Hubbell ConnectorsAluminum Inches (cm)F A B C D EThroat Across AcrossN.P.T. Form Dia. Ref Dia. Corners Flats-18 1 .88" 1.40" .560" .44" .94" .81"(2.24) (3.56) (1.42) (1.12) (2.39) (2.06)½-14 2 1.13" 1.80" .560" .63" 1.15" 1.00"(2.87) (4.57) (1.42) (1.60) (2.92) (2.54)¾-14 2 1.13" 2.10" .750" .63" 1.44" 1.25"(2.87) (5.33) (1.90) (1.60) (3.66) (3.17)1-11½ 4 1.75" 2.30" .880" 1.10" 1.88" 1.63"(4.44) (5.84) (2.24) (2.79) (4.78) (4.14)1¼-11½ 5 2.31" 2.80" .950" 1.43" 2.64" 2.29"(5.87) (7.11) (2.41) (3.63) (6.71) (5.82)1½-11½ 5 2.31" 2.80" .950" 1.43" 2.64" 2.29"(5.87) (7.11) (2.41) (3.63) (6.71) (5.82)Product DataDust-Tight Strain Relief Grips for Insulated CablesKellems Strain Relief Grips connect flexible cord or bus drop cable to electricalenclosures. For indoor use only, they are available with either insulated or noninsulatedaluminum fittings, and feature single weave, galvanized steel meshgrips with patented wide range mesh construction. They come with a locknutand a neoprene gasket that provides a dust tight seal.ApplicationUsed to connect electrical cable to power boxes, cabinets, panel boards, powercenters, machine tools and with bus drop systems.Benefits• Helps prevent cord or cablepull-out.• Provides a dust tight seal.• Easy installation.• Patented mesh construction.• One piece design.I-Grips for Insulated CablesKellems I-Grips are made of high strength, plastic coated galvanized steelstrand. They are offered in six sizes to fit all cable diameters used with HubbellInsulgrip ® Kellems l-Grips will control cable arc-of-bend and reduce high pulltensions from being transmitted to the wiring terminals.ApplicationKellems I-Grips will fit 2, 3, 4 and 5 wire Hubbell Insulgrip plugs and connectorbodies. The eye tabs fit under the nylon cord clamp and the screws slidethrough the eyelets, securing the grip in place.I-Grips can be used on any Insulgrip cord set which requires cable, arc-of-bendcontrol or heavy duty strain relief. Cord sets used at in-door construction sites orfor plant maintenance jobs are examples.These grips are for indoor use only.Benefits• Easily attached to Insulgrip plugsand connector bodies.• Fits all sizes.• Provides heavy duty strain relief.• Controls cable arc-of-bend.Note: I-Grips should not be used on Insulgrip devices when “Seal-Tite ® ” weatherproofcovers are to be installed.T-76 www.hubbell-wiring.comDimensions in Inches (mm)