Hubbell Wiring Device.pdf - Eversave Technology
Hubbell Wiring Device.pdf - Eversave Technology Hubbell Wiring Device.pdf - Eversave Technology
Conduit Riser Grips Kellems ® Wire Management ProductsKellems ® Wire Management ProductsTechnical InformationSupport GripsFor Support Grips Only*Multiple Cable Selection Charts for Cables and Wires of Unequal DiametersHow to choose the correct grip size:1. Find the Grip Circumference Range by measuring the circumferenceof the bundle of different diameter cables to be gripped (see illustration).2. Divide the bundle circumference by 3.14 to determine the diameter.3. Choose a grip offering a range of cable diameters the same as thecable diameter.For Cables of Equal DiametersUnder “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range tothe right.If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.Example:3 cables, each with .89" (2.26cm) diameter, for a Closed Grip select the 1.50"-1.74" (3.81cm-4.42cm) range,for a Split Grip select the 1.75"-1.99" (4.44cm-5.05cm) range.Number of Cables in One GripGrip Dia. Range2 3 4 5 6 and 7 8 9 Inches (cm).30-.38 .25-.31 .22-.27 .19-.24 .17-.22 .15-.19 .14-.18 .50-.61(.76-.97) (.63-.79) (.56-.69) (.48-.61) (.43-.56) (.38-.48) (.36-.46) (1.27-1.55).38-.44 .31-.36 .27-.31 .24-.29 .22-.26 .19-.23 .18-.21 .62-.74(.97-1.12) (.79-.91) (.69-.79) (.61-.74) (.56-.66) (.48-.58) (.46-.53) (1.57-1.88).44-.59 .36-.49 .31-.42 .29-.38 .26-.34 .23-.31 .21-.28 .75-.99(1.12-1.50) (.91-1.24) (.79-1.07) (.74-.97) (.66-.86) (.58-.79) (.53-.71) (1.90-2.51).59-.75 .49-.63 .42-.54 .38-.48 .34-.43 .31-.39 .28-.35 1.00-1.24(1.50-1.90) (1.24-1.60) (1.07-1.37) (.97-1.22) (.86-1.09) (.79-.99) (.71-.89) (2.54-3.15).75-.90 .63-.76 .54-.65 .48-.58 .43-.52 .39-.46 .35-.42 1.25-1.49(1.90-2.29) (1.60-1.93) (1.37-1.65) (1.22-1.47) (1.09-1.32) (.99-1.17) (.89-1.07) (3.17-3.78).90-1.07 .76-.89 .65-.77 .58-.67 .52-.60 .46-.54 .42-.49 1.50-1.74(2.29-2.72) (1.93-2.26) (1.65-1.96) (1.47-1.70) (1.32-1.52) (1.17-1.37) (1.07-1.24) (3.81-4.42)1.07-1.22 .89-1.02 .77-.88 .67-.77 .60-.69 .54-.62 .49-.56 1.75-1.99(2.72-3.10) (2.26-2.59) (1.96-2.24) (1.70-1.96) (1.52-1.75) (1.37-1.57) (1.24-1.42) (4.44-5.05)1.22-1.53 1.02-1.28 .88-1.10 .77-.96 .69-.86 .62-.77 .56-.71 2.00-2.49(3.10-3.89) (2.59-3.25) (2.24-2.79) (1.96-2.44) (1.75-2.18) (1.57-1.96) (1.42-1.80) (5.08-6.32)1.53-1.83 1.28-1.53 1.10-1.32 .96-1.16 .86-1.03 .77-.93 .71-.85 2.50-2.99(3.89-4.65) (3.25-3.89) (2.79-3.35) (2.44-2.95) (2.18-2.62) (1.96-2.36) (1.80-2.16) (6.35-7.59)1.83-2.14 1.53-1.79 1.32-1.54 1.16-1.35 1.03-1.20 .93-1.08 .85-.99 3.00-3.49(4.65-5.44) (3.89-4.55) (3.35-3.91) (2.95-3.43) (2.62-3.05) (2.36-2.74) (2.16-2.51) (7.62-8.86)2.14-2.44 1.79-2.05 1.54-1.76 1.35-1.54 1.20-1.37 1.08-1.24 .99-1.13 3.50-3.99(5.44-6.20) (4.55-5.21) (3.91-4.47) (3.43-3.91) (3.05-3.48) (2.74-3.15) (2.51-2.87) (8.89-10.13)2.44-2.75 2.05-2.30 1.76-1.98 1.54-1.74 1.37-1.55 1.24-1.39 1.13-1.27 4.00-4.49(6.20-6.98) (5.21-5.84) (4.47-5.03) (3.91-4.42) (3.48-3.94) (3.15-3.53) (2.87-3.23) (10.16-11.40)2.75-3.06 2.30-2.56 1.98-2.20 1.74-1.93 1.55-1.72 1.39-1.55 1.27-1.41 4.50-4.99(6.98-7.77) (5.84-6.50) (5.03-5.59) (4.42-4.90) (3.94-4.37) (3.53-3.94) (3.23-3.58) (11.43-12.67)Note: *This chart is to be used for determining grip size when multiple cables are held in a single Support Grip. For Conduit Risermultiple cable selection, see page T-47. It is always recommended that, when multiple cables are installed in a Support Grip,the tail end of the grip be banded after installation on the cable bundle.T-46 www.hubbell-wiring.comDimensions in Inches (mm)
Kellems ® Wire Management ProductsTechnical InformationConduit Riser Support GripsFor Conduit Riser Grips Only*Multiple Cable Selection Charts for Cables and Wires of Unequal DiametersHow to choose the correct grip size:1. Find the Grip Circumference Range by measuring the circumferenceof the bundle of different diameter cables to be gripped (see illustration).2. Divide the bundle circumference by 3.14 to determine the diameter.3. Choose a grip offering a range of cable diameters the same as thecable diameter.For Cables of Equal DiametersUnder “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range tothe right.If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.Example:3 cables, each with .89" (2.26cm) diameter, for a Closed Grip select the 1.50"-1.74" (3.81cm-4.42cm) range,for a Split Grip select the 1.75"-1.99" (4.44cm-5.05cm) range.Number of Equal Diameter Cables in One GripGrip Dia. Range2 3 4 5 6 and 7 8 9 Inches (cm).29-.36 .24-.30 .21-.25 .18-.22 .16-.20 .15-.18 .14-.17 .50-.62(.74-.91) (.61-.76) (.53-.63) (.46-.56) (.41-.51) (.38-.46) (.36-.43) (1.27-1.57).37-.43 .31-.36 .26-.30 .23-.27 .21-.24 .19-.22 .18-.20 .63-.74(.94-1.09) (.79-.91) (.66-.76) (.58-.69) (.53-.61) (.48-.56) (.46-.51) (1.60-1.88).44-.58 .37-.48 .31-.41 .28-.36 .25-.32 .23-.29 .21-.27 .75-.99(1.12-1.47) (.94-1.22) (.79-1.04) (.71-.91) (.63-.81) (.58-.74) (.53-.69) (1.90-2.51).59-.72 .49-.60 .42-.51 .37-.45 .33-.40 .30-.36 .28-.34 1.00-1.34(1.50-1.83) (1.24-1.52) (1.07-1.30) (.94-1.14) (.84-1.02) (.76-.91) (.71-.86) (2.54-3.15).73-.87 .61-.72 .52-.61 .46-.54 .41-.48 .37-.43 .35-.40 1.25-1.49(1.85-2.21) (1.55-1.83) (1.32-1.55) (1.17-1.37) (1.04-1.22) (.94-1.09) (.89-1.02) (3.17-3.78).88-1.01 .73-.85 .62-.71 .55-.63 .49-.56 .44-.51 .41-.47 1.50-1.74(2.24-2.57) (1.85-2.16) (1.57-1.80) (1.40-1.60) (1.24-1.42) (1.12-1.30) (1.04-1.19) (3.81-4.42)1.02-1.16 .86-.96 .72-.81 .64-.72 .57-.64 .52-.58 .48-.54 1.75-1.99(2.59-2.95) (2.18-2.44) (1.83-2.06) (1.63-1.83) (1.45-1.63) (1.32-1.49) (1.22-1.37) (4.44-5.05)1.17-1.44 .97-1.20 .82-1.02 .73-.90 .65-.80 .59-.72 .55-.67 2.00-2.49(2.97-3.66) (2.46-3.05) (2.08-2.59) (1.85-2.29) (1.65-2.03) (1.50-1.83) (1.40-1.70) (5.08-6.32)1.45-1.73 1.21-1.45 1.03-1.22 .91-1.08 .81-.96 .73-.87 .68-.81 2.50-2.99(3.68-4.39) (3.07-3.68) (2.62-3.10) (2.31-2.74) (2.06-2.44) (1.85-2.21) (1.73-2.06) (6.35-7.59)1.74-2.02 1.46-1.69 1.23-1.43 1.09-1.26 .97-1.11 .83-1.01 .82-.94 3.00-3.49(4.42-5.13) (3.71-4.29) (3.12-3.63) (2.77-3.20) (2.46-2.82) (2.11-2.57) (2.08-2.39) (7.62-8.86)2.03-2.31 1.70-1.93 1.44-1.63 1.27-1.44 1.12-1.27 1.02-1.15 .95-1.08 3.50-3.99(5.16-5.87) (4.32-4.90) (3.66-4.14) (3.23-3.66) (2.84-3.23) (2.59-2.92) (2.41-2.74) (8.89-10.13)Note: *This chart is to be used for determining grip size when multiple cables are held in a single Conduit Riser Grip. For Support Gripmultiple cable selection, see page T-46. It is always recommended that, when multiple cables are installed in a Conduit Riser Grip,the tail end of the grip be banded after installation on the cable bundle.Kellems ® Wire Management Products Technical InformationDimensions in Inches (mm)www.hubbell-wiring.comT-47
- Page 631 and 632: Temporary Power Distribution System
- Page 633 and 634: Temporary Power Distribution System
- Page 635 and 636: Temporary Power Distribution System
- Page 637 and 638: Section TKellems ® Wire Management
- Page 639 and 640: Kellems ® Wire Management Products
- Page 641 and 642: Kellems ® Wire Management Products
- Page 643 and 644: Kellems ® Wire Management Products
- Page 645 and 646: Kellems ® Wire Management Products
- Page 647 and 648: Kellems ® Wire Management Products
- Page 649 and 650: Kellems ® Wire Management Products
- Page 651 and 652: Kellems ® Wire Management Products
- Page 653 and 654: Kellems ® Wire Management Products
- Page 655 and 656: Kellems ® Wire Management Products
- Page 657 and 658: Kellems ® Wire Management Products
- Page 659 and 660: Kellems ® Wire Management Products
- Page 661 and 662: Kellems ® Wire Management Products
- Page 663 and 664: Kellems ® Wire Management Products
- Page 665 and 666: Kellems ® Wire Management Products
- Page 667 and 668: Kellems ® Wire Management Products
- Page 669 and 670: Kellems ® Wire Management Products
- Page 671 and 672: Kellems ® Wire Management Products
- Page 673 and 674: Kellems ® Wire Management Products
- Page 675 and 676: Wire Management ProductsConduit Ris
- Page 677 and 678: Kellems ® Wire Management Products
- Page 679 and 680: Kellems ® Wire Management Products
- Page 681: Kellems ® Wire Management Products
- Page 685 and 686: Kellems ® Wire Management Products
- Page 687 and 688: Kellems ® Wire Management Products
- Page 689 and 690: Kellems ® Wire Management Products
- Page 691 and 692: Kellems ® Wire Management Products
- Page 693 and 694: Kellems ® Wire Management Products
- Page 695 and 696: Kellems ® Wire Management Products
- Page 697 and 698: Kellems ® Wire Management Products
- Page 699 and 700: Kellems ® Wire Management Products
- Page 701 and 702: Kellems ® Wire Management Products
- Page 703 and 704: Kellems ® Wire Management Products
- Page 705 and 706: Kellems ® Wire Management Products
- Page 707 and 708: Kellems ® Wire Management Products
- Page 709 and 710: Kellems ® Wire Management Products
- Page 711 and 712: Kellems ® Wire Management Products
- Page 713 and 714: Kellems ® Wire Management Products
- Page 715 and 716: Kellems ® Wire Management Products
- Page 717 and 718: Kellems ® Wire Management Products
- Page 719 and 720: Kellems ® Wire Management Products
- Page 721 and 722: Kellems ® Wire Management Products
- Page 723 and 724: Kellems ® Wire Management Products
- Page 725 and 726: Kellems ® Wire Management Products
- Page 727 and 728: Kellems ® Wire Management Products
- Page 729 and 730: Kellems ® Wire Management Products
- Page 731 and 732: Kellems ® Wire Management Products
Conduit Riser Grips Kellems ® Wire Management ProductsKellems ® Wire Management ProductsTechnical InformationSupport GripsFor Support Grips Only*Multiple Cable Selection Charts for Cables and Wires of Unequal DiametersHow to choose the correct grip size:1. Find the Grip Circumference Range by measuring the circumferenceof the bundle of different diameter cables to be gripped (see illustration).2. Divide the bundle circumference by 3.14 to determine the diameter.3. Choose a grip offering a range of cable diameters the same as thecable diameter.For Cables of Equal DiametersUnder “Number of Cables in One Grip”, find the diameter of your single cable in vertical column. Read the grip diameter range tothe right.If your diameter is the maximum of the range shown, go to the next larger size for Split Grips, stay with the same size for Closed Grips.Example:3 cables, each with .89" (2.26cm) diameter, for a Closed Grip select the 1.50"-1.74" (3.81cm-4.42cm) range,for a Split Grip select the 1.75"-1.99" (4.44cm-5.05cm) range.Number of Cables in One GripGrip Dia. Range2 3 4 5 6 and 7 8 9 Inches (cm).30-.38 .25-.31 .22-.27 .19-.24 .17-.22 .15-.19 .14-.18 .50-.61(.76-.97) (.63-.79) (.56-.69) (.48-.61) (.43-.56) (.38-.48) (.36-.46) (1.27-1.55).38-.44 .31-.36 .27-.31 .24-.29 .22-.26 .19-.23 .18-.21 .62-.74(.97-1.12) (.79-.91) (.69-.79) (.61-.74) (.56-.66) (.48-.58) (.46-.53) (1.57-1.88).44-.59 .36-.49 .31-.42 .29-.38 .26-.34 .23-.31 .21-.28 .75-.99(1.12-1.50) (.91-1.24) (.79-1.07) (.74-.97) (.66-.86) (.58-.79) (.53-.71) (1.90-2.51).59-.75 .49-.63 .42-.54 .38-.48 .34-.43 .31-.39 .28-.35 1.00-1.24(1.50-1.90) (1.24-1.60) (1.07-1.37) (.97-1.22) (.86-1.09) (.79-.99) (.71-.89) (2.54-3.15).75-.90 .63-.76 .54-.65 .48-.58 .43-.52 .39-.46 .35-.42 1.25-1.49(1.90-2.29) (1.60-1.93) (1.37-1.65) (1.22-1.47) (1.09-1.32) (.99-1.17) (.89-1.07) (3.17-3.78).90-1.07 .76-.89 .65-.77 .58-.67 .52-.60 .46-.54 .42-.49 1.50-1.74(2.29-2.72) (1.93-2.26) (1.65-1.96) (1.47-1.70) (1.32-1.52) (1.17-1.37) (1.07-1.24) (3.81-4.42)1.07-1.22 .89-1.02 .77-.88 .67-.77 .60-.69 .54-.62 .49-.56 1.75-1.99(2.72-3.10) (2.26-2.59) (1.96-2.24) (1.70-1.96) (1.52-1.75) (1.37-1.57) (1.24-1.42) (4.44-5.05)1.22-1.53 1.02-1.28 .88-1.10 .77-.96 .69-.86 .62-.77 .56-.71 2.00-2.49(3.10-3.89) (2.59-3.25) (2.24-2.79) (1.96-2.44) (1.75-2.18) (1.57-1.96) (1.42-1.80) (5.08-6.32)1.53-1.83 1.28-1.53 1.10-1.32 .96-1.16 .86-1.03 .77-.93 .71-.85 2.50-2.99(3.89-4.65) (3.25-3.89) (2.79-3.35) (2.44-2.95) (2.18-2.62) (1.96-2.36) (1.80-2.16) (6.35-7.59)1.83-2.14 1.53-1.79 1.32-1.54 1.16-1.35 1.03-1.20 .93-1.08 .85-.99 3.00-3.49(4.65-5.44) (3.89-4.55) (3.35-3.91) (2.95-3.43) (2.62-3.05) (2.36-2.74) (2.16-2.51) (7.62-8.86)2.14-2.44 1.79-2.05 1.54-1.76 1.35-1.54 1.20-1.37 1.08-1.24 .99-1.13 3.50-3.99(5.44-6.20) (4.55-5.21) (3.91-4.47) (3.43-3.91) (3.05-3.48) (2.74-3.15) (2.51-2.87) (8.89-10.13)2.44-2.75 2.05-2.30 1.76-1.98 1.54-1.74 1.37-1.55 1.24-1.39 1.13-1.27 4.00-4.49(6.20-6.98) (5.21-5.84) (4.47-5.03) (3.91-4.42) (3.48-3.94) (3.15-3.53) (2.87-3.23) (10.16-11.40)2.75-3.06 2.30-2.56 1.98-2.20 1.74-1.93 1.55-1.72 1.39-1.55 1.27-1.41 4.50-4.99(6.98-7.77) (5.84-6.50) (5.03-5.59) (4.42-4.90) (3.94-4.37) (3.53-3.94) (3.23-3.58) (11.43-12.67)Note: *This chart is to be used for determining grip size when multiple cables are held in a single Support Grip. For Conduit Risermultiple cable selection, see page T-47. It is always recommended that, when multiple cables are installed in a Support Grip,the tail end of the grip be banded after installation on the cable bundle.T-46 www.hubbell-wiring.comDimensions in Inches (mm)