Manual HAHSON SR8 PLUS - VTP UP

More documents

Recommendations

Info

SR8-Plus Operation Manual73-100-810-I5.28 Serial Number LogThe Serial Number Log is used to keep track of the serial numbers of the Vessels, Paddles,Basket Shafts and Baskets, as well as a System Serial Number Log. The function can beused to input the serial number data or simply to view and/or print a reference of the positionof the accessories. To perform this function:1. With the Main screen displayed, press [PREFERENCES] to display the SystemOptions screen.2. Press [3] to select "Validation".3. Press [2], the “Serial Number Log” screen is displayed.Figure 5-12: Serial Number Log Screen4. Use the [←] [→] and [↓][↑] keys to navigate through the Vessels, Paddles, BasketShafts, Baskets and System Serial Number input pages. Pressing the correspondingnumeric keys gets you into the edit mode; this allows you to input data into the currentfield. Digital Temperature Probe serial numbers are automatically placed into theircorresponding fields and are not editable.5. Press [PRINT OPTION] to print the serial numbers and shaft positions currentlyon the screen.6. Press [ENTER] to accept the changes and exit the edit mode. Press [ESC] to undocurrent entry and exit edit mode. Press [ESC] again to return to the Validation Menu.Section 5 Operation and Programming – 45 –
SR8-Plus Operation Manual73-100-810-I5.29 Software Flow ChartstumnovwxSTOP PROTOCOL / STAND BY1. ADJUST CONTRAST2 HEATER STAYS ON / HEATER SHUTDOWN3 VALIDATION4 CALIBRATION5 SECURITY6 DIAGNOSTICS7 SYSTEM CONFIG1 DEVICE SETUP2 SYSTEM ID3 EDIT TITLES4 LANGUAGE [ENG]5 RS-232 SETUP6 E-PROBE SETUP1 LOG VESSEL TEMPERATURE2 LOG SERIAL NUMBERS3 MAINTENANCE LOG1 ANALOG PROBE OFFSET ADJUST2 ANALOG PROBE CALIBRATION3 BATH TEMPERATURE CALIBRATION4 MOTOR CALIBRATION5 DIGITAL PROBE OFFSET ADJUSTSYSTEMCONTROLMOTORHEATERBATHCIRCULATORPROBE 1PROBE 2HEATER CONTROLTEMP PROBE(S)MOTOR CONTROLBELT TIMEMOTOR TIMEHEATER TIMEVESSELSPADDLESBASKET SHAFTSBASKETSDIGITAL PROBESSYSTEM COMPONENTS1 PRINTER: YES / NO3 TEMP PROBES: 1 / 22 TOLERANCE: USP/OFF4 SAMPLER: AUTOPLUS / DISSOETTE II / TRANSFER MODULE / MULTI-DOSE / NONE5 SAMPLING PROBE: AUTOPROBE / E-PROBES / NONE1 PREHEAT WAKEUP2 SAMPLING ALARM3 USER ALARMS4 CALIB. ALARM5 CLOCK OPTIONS6 START TIMER1 BAUD: 9600 / 1200 / 2400 / 48002 BITS: 8 / 73 PARITY: NONE / ODD / EVEN4 ECHO: ON / OFFRAISE PROBES LOWER PROBES1 HOME PROBES2 STROKE: 1L FLASK (45 mm) / 2L FLASK (90mm) / SMALL VOL (45mm)abcghidefRUN PROTOCOL 1-25SET BATH TEMPERATURESET DRIVE SPEEDjklpqryz()EDIT PROTOCOL 1-251 DRIVE SPEED:2 BATH TEMPERATURE:3 TEST LENGTH:4 PRINT STATUS:1 SAMPLING EVENTS:2 STAGGER EXTENSION:3 INFINITY TEST LEN:4 INFINITY TEST SPD:SAMPLING TIMES:1 DRUG NAME:2 DOSAGE:3 PROTOCOL ID:4 APPARATUS:5 MEDIA TYPE:6 MEDIA VOLUME:7 SAMPLE VOLUME:8 COMMENTS:E-PROBE USAGE:1. PRINT STATUS2. PRINT PROTOCOL3. PRINT HEADER4. PRINT LAST TEST5 DELAY: XXXX SEC.4 RAISE: ON EXTERNAL SIGNAL / AFTER DELAY3 LOWER: AT SAMPLE TIME / ON EXTERNAL SIGNAL2 STROKE: XXXmm1 SETTING: CUSTOM1. UNIT OPERATION2. USP DISSO. SPEC3. CALIB. TIPS1 DIGITAL PROBES2 VESSEL GOAL TEMPSection 5 Operation and Programming – 46 –
Page 2 and 3: SR8-Plus Operation Manual73-100-810
Page 72: SR8-Plus Operation Manual73-100-810

Manual HAHSON SR8 PLUS - VTP UP

Create successful ePaper yourself

Delete template?

Save as template?