cargo carrier - BOB Trailers and Strollers

DETACH harness strapUsing a Phillipsscrewdriver, removeboth harness-strapscrews from strollerswing arms.PARTIALLY DETACH lowboyUsing a Phillips screwdriver and 8mmsocket wrench, undo both Lowboyattachments from underside of seat.NOTE: Applying heatfrom soldering ironmay help releasethread lock.Swing Armunfold strollerLift handlebar until it snapsinto upright position.remove fabric seatBeginning at bottom, use a Phillipsscrewdriver to remove fabric screws.Nose CoverBottomNOTE:Top two screws are“long” fabric screws andwill not be used with RCCK.release velcro SEAT strapUndo velcro seat strap andremove fabric seat.OMA42P

ATTACH RCCKASSEMBLE SCREW, PLUG AND BARInsert one pivot screw through oneend of main bar and into pivot plug.Pivot PlugPivot ScrewMain BarPOSITION RCCKINSERT PIVOTPLUG and screwSupport ArmsSlip pivot plug into openingon pivot bracket and pushpivot screw flush against bar.Holding pivot screw andpivot plug in place with handon one side, position both endsof main bar over pivot brackets.PivotBracketNOTE: Position support arms abovemain bar before installing pivot screws.ATTACH PIVOT NUTSlip pivot nut on other endof pivot screw and intoopening on pivot bracket.TIGHTEN PIVOT NUTUse a Phillips screwdriver totighten pivot screw clockwise,while holding pivot nut.OMA42P

INSERT PIVOT PLUGON OPPOSITE SIDESlip pivot plug underend of main bar andinto opening on pivotbracket.INSERT PIVOT SCREWInsert pivot screw throughmain bar, pivot plug and intoopening on pivot bracket.ATTACH pivot nutSlip pivot nut on other endof pivot screw and intoopening on pivot bracket.PivotBracketPivotBracketTIGHTEN PIVOT NUTUse a Phillipsscrewdriver to tightenpivot screw clockwise,while holding pivot nut.ATTACH nose clip TONOSE COVERClip underside of nose fabric toplastic nose cover from stroller.POSITION NOSE COVERAlign plastic nose cover holeswith holes in stroller frame.INSERT FABRIC SCREWSUsing a Phillips screwdriver,insert fabric screws. Tighten.WarningDO NOT CROSSTHREADIf screw does not turn easily,unscrew and start again.OMA42P

POSITION ARMAlign support arm hole with lowestthreaded hole in handlebar frame.INSERT SHARP SCREWInsert sharp screw throughend of support arm and intohandlebar.TIGHTEN SHARP SCREWTighten firmly with Phillips screwdriver.Attach rcck fabricBeginning at top, use a Phillips screwdriverand insert fabric screws.WarningDO NOT CROSSTHREADIf screw does notturn easily, unscrewand start again.FOLD STROLLERCompress bothhandlebar releaselevers and foldhandlebar forward.reattach lowboyUsing a Phillips screwdriver and 8mm-socketwrench, reattach lowboy to underside of RCCK.OMA42P

POSITION cableRoute cable through upper loops onunderside of RCCK. Red handle shouldrest between upper loops.Continue routing through lower loops.REATTACH CABLEHolding knob with one hand, insertscrew through cable end and alignwith inside knob hole. Tighten screw.Repeat on opposite side withunattached cable end.Red HandleRed HandleOMA42P

Revolution Cargo Conversion Kit Warnings• This product is not designed to be a used as astroller, children and other living things shouldnever be placed inside or on top of the RCCK.• The BOB Revolution Cargo Conversion Kitis designed for use with the BOB Revolutionstrollers. This product was not designed for, norwill it fit any BOB fixed-wheel or duallie strollers.• Read and understand all owner’s manualsand warnings for all BOB products used withthe RCCK before use. If you are unclear on anypoint, contact your dealer, place of purchaseor BOB [toll free 1-800-893-2447] before use.A list of dealers is listed on our website[www.bobgear.com]. For updates to this manual,our warranty and for other recent productnotifications, please visit www.bobgear.comperiodically.• Follow assembly instructions. Failure to properlyinstall this accessory product may result inaccidents, damage or injury. If you are not sureyou can properly install this accessory, contactyour BOB retailer and arrange for them toperform the installation.• Do not use the RCCK off-road or on uneventerrain. Doing so may result in accidents,damage or injury.• B.O.B is a registered trademark of BOBTrailers, Inc.LIMITED WARRANTYBOB Trailers Inc. takes pride in its workmanship and strives to manufacture the best products possible.Therefore, we warranty our BOB RCCK against defects in material and workmanship subject to theconditions listed below. Since no product is indestructible, it does not cover defects attributable to orresulting from normal wear, abuse or alteration.• The RCCK is warranted for one year.• Warranty is only valid for the original purchaser.• Proof of purchase is required to exercise thiswarranty.• Labor and transportation are not included.• Normal wear, neglect, abuse, accidents, improperassembly or maintenance, or the installationof parts or accessories not compatible with theoriginal intended use of the cargo carrier, as sold,are not covered by this warranty.• Warranty claims must be made throughan authorized dealer.• This warranty is limited to the replacementof the defective part. BOB Trailersshall in no event be responsible for consequentialor special damages.• This limited warranty is the only expressor implied warranty applicable to BOBTrailers. Any implied warranties, includingwarranties of merchantability and fitnessshall be limited in scope and duration inaccordance with this limited warranty.BOB IS NOT RESPONSIBLE FOR INJURY, DAMAGE OR FAILURE THAT RESULTSFROM OWNERS FAULTY ASSEMBLY OR MAINTENANCE AFTER SHIPPING.OMA42P