For more information please download our ... - Castolin Eutectic

WELDING PARAMETERS:Preparation: Higher carbon steels up to 0.40% carbon should be preheated in the range of 350-500°F (177-260° C). NOTE:High-end carbon steels should use a butttering pass of XHD 6868 or similar product. When welding manganese steel castingsdirectly, or steels with a high hardenability, TeroMatec 688OA or 690OA offer an ideal cushion layer to further optimizethe wear resistance of 395N. DO NOT WELD DIRECTLY ON MANGANESE STEELS, WILL NOT BOND!NOTE: Higher preheats up to 600°F (315°C) will reduce microfissuring.Welding Technique: As indicated in the parameters, there are certain advantages in using either a “push” or “pull” methodduring welding. For most downhand welding the pull method is suggested with the wire positioned at a 70°-80° angle. Thiswill provide a clean, virtually spatter-free, high-crowned weld deposit. 395N can be utilized as an open arc wire requiringno shielding gas.TECHNICAL DATA:Operating Conditions:CURRENT VOLTAGE AMPERAGE STICK-OUT (MIG) STICK-OUT (OPEN ARC) PKG. DIA.DCEP (+) 25-34 170-300 1/2” - 3/4” 1” - 1 1/4”33 lb. (15KG)coils0.045” (1.2mm)1/16” (1.6mm)Typical Mechanical Values:Typical Hardness 1st Pass: 68-70 HRCTypical Hardness 2nd Pass: 69-71 HRCTemperature Limit: 1,400°F (760°C)Carbide Type: Complex borocarbide matrix ofsub-micron, near-nano scale microstructureParameters:Position: Pull TechniqueShielding Gasses: a. Recommended gas mixture: 98% Ar + 2% O2b. Alternative gas mixture: 75%Ar + 25% CO2c. 90%Ar + 10%CO2Flow Rates: 30-35 SCFH (15-17 L/min.)Typical Coverage: 5.5lbs will cover 1 sq.ft. x 1/8” thickAPPLICATIONS:Note 1 - MIG or Open Arc: Nanoalloy 395 N wire works very well with or without shielding gas.When using extended welding parameters the shielding gas helps reduce heat buildup in the welding gun assembly.Designed for protective coatings with extreme resistance to abrasion, erosion combined with moderate shock on carbon,alloy, stainless and cast steels.APPLICATIONSINDUSTRIESBucket Teeth/LipsMiningCrusher BarsEarth MovingShreddersWaste/RecyclingFeed ScrewsPulp and PaperRoll CrushersIron and Steel WorksDredging TeethRecycling KnivesConstructionWaste/RecyclingFoundry sand slingerWaste cutting knifeBucket teethClay Mixer ScrewsCrusher Star

Stronger with...EutecticWEAR & FUSION TECHNOLOGYYOUR RESOURCE FOR PROTECTION, REPAIR AND JOINING SOLUTIONSEutectic CorporationN94 W14355 Garwin Mace DriveMenomonee Falls, WI 53051 USAP 800-558-8524 • F 262-255-5542www.eutecticusa.comEutectic Canada428, rue Aime VincentVaudreuil-Dorion, Quebec J7V 5V5Phone: (800) 361-9439Fax: (514) 695-8793www.eutectic-na.comEutectic MexicoKM 36.5 AutopistaMexico-Quertaro54730 Cautitlan-IzcalliEstado de Mexico, MexicoPhone: 011 (52) 55-5872-1111e-mail: eutectic.mexico@eutectic.com.mxStatement of Liability: Due to variations inherent in specifi c applications, the technical information contained herein, including any information as to suggested product applications or results, is presented withoutrepresentation or warranty, expressed or implied. Without limitation, there are no warranties of merchantability or of fi tness for a particular purpose. Each process and application must be fully evaluated by the user inall respects, including suitability, compliance with applicable law and non-infringement of the rights of others, and Eutectic Corporation and its affi liates shall have no liability in respect thereof.395-10-12-10© 2008, Eutectic Corporation, ® Reg. T.M., Printed in the U.S.A.