RS-1000 Manual - kamery airlive airlivecam
RS-1000 Manual - kamery airlive airlivecam RS-1000 Manual - kamery airlive airlivecam
Security Bandwidth Manager RebootOnce this function is enabled, the Security Bandwidth Manager will be rebooted.Reboot Security Bandwidth Manager: Click Reboot.A confirmation pop-up box will appear. Follow the confirmation pop-up box, click OK to restartSecurity Bandwidth Manager or click Cancel to discard changesFigure1-13 Reboot Security Bandwidth Manager15
Date/TimeSynchronizing the Bandwidth Manager with the System ClockAdmins can configure the Security Bandwidth Manager.s date and time by eithersyncing to an Internet Network Time Server (NTP) or by syncing to your computer.sclock.Follow these steps to sync to an Internet Time ServerStep 1. Enable synchronization by checking the box.Step 2. Click the down arrow to select the offset time from GMT.Step 3. Enter the Server IP Address or Server name with which you want tosynchronize.Step 4. Update system clock every 5 minutes You can set the intervaltime to synchronize with outside servers. If you set it to 0, it meansthe device will not synchronize automatically.Follow this step to sync to your computer’s clock.Step 1. Click on the Sync button.Click OK to apply the setting or click Cancel to discard changes.Figure1-14 System Time16
- Page 1 and 2: AirLive RS-1000Security Bandwidth M
- Page 3 and 4: Software Update43Interface 44Addres
- Page 5 and 6: Event Alarm151Accounting Report 154
- Page 7 and 8: Multiple NAT Multiple NAT allows lo
- Page 9 and 10: Changing the Main/Sub-Administrator
- Page 11 and 12: Removing a Sub AdministratorStep 1.
- Page 13 and 14: Exporting Security Bandwidth Manage
- Page 15 and 16: Restoring Factory Default SettingsS
- Page 17 and 18: Web Manager (WAN Interface) (Remote
- Page 19: To-Bandwidth Manager Packets LogOnc
- Page 23 and 24: Permitted IPsOnly the authorized IP
- Page 25 and 26: Modify Permitted IP AddressStep 1.
- Page 27 and 28: Multiple NATMultiple NAT allows loc
- Page 29 and 30: Add Multiple NATStep 1. Click the A
- Page 31 and 32: Delete Multiple NATStep 1. Find the
- Page 33 and 34: " Detect ICMP Flood: Select this op
- Page 35 and 36: Route TableIn this section, the Adm
- Page 37 and 38: Modifying a Static Route:Step 1. In
- Page 39 and 40: DHCPIn the section, the Administrat
- Page 41 and 42: Adding a new Host TableSTEP 1.Selec
- Page 43 and 44: How to register:Firstly, Click Dyna
- Page 45 and 46: Modify dynamic DNSStep 1. Find the
- Page 47 and 48: LogoutStep 1. Select this option to
- Page 49 and 50: InterfaceIn this section, the Admin
- Page 51 and 52: !!46
- Page 53 and 54: 48Fixed: Select this if you were gi
- Page 55 and 56: 50After setting all of the paramete
- Page 57 and 58: 52If you want to set up DNS Server,
- Page 59 and 60: AddressThe Security Bandwidth Manag
- Page 61 and 62: Adding a new LAN AddressStep 1. In
- Page 63 and 64: Removing a LAN AddressStep 1. In th
- Page 65 and 66: Adding a LAN GroupStep 1. In the LA
- Page 67 and 68: Removing a LAN GroupStep 1. In the
- Page 69 and 70: Adding a new WAN AddressStep 1. In
Date/TimeSynchronizing the Bandwidth Manager with the System ClockAdmins can configure the Security Bandwidth Manager.s date and time by eithersyncing to an Internet Network Time Server (NTP) or by syncing to your computer.sclock.Follow these steps to sync to an Internet Time ServerStep 1. Enable synchronization by checking the box.Step 2. Click the down arrow to select the offset time from GMT.Step 3. Enter the Server IP Address or Server name with which you want tosynchronize.Step 4. Update system clock every 5 minutes You can set the intervaltime to synchronize with outside servers. If you set it to 0, it meansthe device will not synchronize automatically.Follow this step to sync to your computer’s clock.Step 1. Click on the Sync button.Click OK to apply the setting or click Cancel to discard changes.Figure1-14 System Time16