RS-1000 Manual - kamery airlive airlivecam
RS-1000 Manual - kamery airlive airlivecam RS-1000 Manual - kamery airlive airlivecam
Enable Log Mail Support & Syslog MessageLog Mail Configuration /Enable Log Mail SupportStep 1. Firstly, go to Admin –Select Enable E-mail Alert Notification under E-MailSettings. Enter the e-mail address to receive the alarm notification. Click OK.Step 2. Go to LOG $Log Backup. Check to enable Log Mail Support. Click OK.System Settings/Enable Syslog MessageStep 1. Check to enable Syslog Message. Enter the Host IP Address and Host Portnumber to receive the Syslog message.Step 2. Click OK.Figure10-11 Log Backup145
Disable Log Mail Support & Syslog MessageStep 1. Go to LOG $Log Backup. Uncheck to disable Log Mail Support. Click OK.Step 2. Go to LOG $Log Backup. Uncheck to disable Settings Message. Click OK.Figure10-12 Disable Log Backup146
- Page 99 and 100: STEP 2.Enter the following setting
- Page 101 and 102: STEP 4.When user_1 is going to acce
- Page 103 and 104: OutgoingThis section describes step
- Page 105 and 106: 100Adding a new Outgoing PolicyClic
- Page 107 and 108: 102Modifying an Outgoing policyStep
- Page 109 and 110: Removing the Outgoing PolicyStep 1.
- Page 111 and 112: 106fourth column is the Alarm Thres
- Page 113 and 114: Adding an Incoming PolicyUnder Inco
- Page 115 and 116: Modifying Incoming PolicyStep 1. In
- Page 117 and 118: Removing an Incoming PolicyStep 1.
- Page 119 and 120: URL BlockingThe Administrator may s
- Page 121 and 122: Adding a URL Blocking policyStep 1.
- Page 123 and 124: Removing a URL Blocking policyStep
- Page 125 and 126: Virtual ServerThe Security Bandwidt
- Page 127 and 128: Mapped IPInternal private IP addres
- Page 129 and 130: Modifying a Mapped IPStep 1. In the
- Page 131 and 132: Virtual ServerVirtual server is a o
- Page 133 and 134: Modifying a Virtual Server IP Addre
- Page 135 and 136: Setting the Virtual Server’s serv
- Page 137 and 138: Modifying the Virtual Server config
- Page 139 and 140: LogThe Security Bandwidth Manager s
- Page 141 and 142: Downloading the Traffic LogsThe Adm
- Page 143 and 144: Event LogWhen the Security Bandwidt
- Page 145 and 146: Clearing the Event LogsThe Administ
- Page 147 and 148: Download LogsStep 1. Click Log in t
- Page 149: Log BackupStep 1. Click Log $Log Ba
- Page 153 and 154: Traffic AlarmIn control policies, t
- Page 155 and 156: Clearing the Traffic Alarm LogsStep
- Page 157 and 158: Downloading the Event Alarm LogsThe
- Page 159 and 160: Accounting ReportAccounting Report
- Page 161 and 162: Outbound Accounting ReportStep 1. C
- Page 163 and 164: Outbound Destination IP Accounting
- Page 165 and 166: Outbound Service Accounting ReportS
- Page 167 and 168: InboundStep 1. Click Service in the
- Page 169 and 170: Inbound Destination IP Accounting R
- Page 171 and 172: Inbound Service Accounting ReportSe
- Page 173 and 174: StatisticsIn this chapter, the Admi
- Page 175 and 176: WAN StatisticsStep 1. Click Statist
- Page 177 and 178: Entering the Policy SatisticsStep 1
- Page 179 and 180: Interface StatusEntering the Interf
- Page 181 and 182: ARP TableEntering the ARP Table win
- Page 183 and 184: Setup ExamplesExample 1: Allow the
- Page 185 and 186: 180
- Page 187 and 188: Step 8. Go to the Incoming window u
- Page 189 and 190: Step 6. In the Add New Policy windo
- Page 191 and 192: Step 7. Click the New Entry button.
- Page 193 and 194: Install a server inside the LAN net
- Page 195 and 196: Step 9. After adding new server IP,
- Page 197: Step 14. In the Add New Policy wind
Enable Log Mail Support & Syslog MessageLog Mail Configuration /Enable Log Mail SupportStep 1. Firstly, go to Admin –Select Enable E-mail Alert Notification under E-MailSettings. Enter the e-mail address to receive the alarm notification. Click OK.Step 2. Go to LOG $Log Backup. Check to enable Log Mail Support. Click OK.System Settings/Enable Syslog MessageStep 1. Check to enable Syslog Message. Enter the Host IP Address and Host Portnumber to receive the Syslog message.Step 2. Click OK.Figure10-11 Log Backup145