RS-1000 Manual - kamery airlive airlivecam

More documents

Recommendations

Info

IncomingThis chapter describes steps to create policies for packets and services from the WANnetwork to the LAN network including Mapped IP and Virtual Server.Enter Incoming windowStep 1. Click Incoming under the Policy menu to enter the Incoming window. TheIncoming table will display current defined policies from the WAN network toassigned Mapped IP or Virtual Server.!!Figure7-5 Incoming PolicyDefinition (Incoming):No.: The numbering of the selected Policy, starting with Number 1.Source Address: The WAN address was selected in WAN function of the Address Table.Destination Address: The mapped IP or Virtual Server IP configured in the Mapped IP orVirtual Server 1/2/3/4 window under Virtual Server function.Service: The service item provided by Virtual Server (or Mapped IP).Action: Control actions to permit or reject packets from LAN networks to WAN network orVirtual Server (Mapped IP) traveling through the Security Bandwidth Manager.Option: Control actions to monitor packets from WAN network or Virtual Server (Mapped IP)traveling through the Security Bandwidth Manager. The first column is the logging function.The second column is the Statistics function. The third column is the Schedule function. The105
106fourth column is the Alarm Threshold function. The fifth column is the QoS function. If thefigures appear in the column, it means that the function is enabled. On the other hand, if thereis no figures appeared in the column, it means that the function is not enabled.The fields of the Incoming window are:" Source: source networks which are specified in the WAN section of theAddress menu, or all the WAN network addresses." Destination: destination networks, which are IP Mapping addresses orVirtual server network addresses created in Virtual Server menu." Service: services supported by Virtual Servers (or Mapped IP)." Action: control actions to permit or deny packets from WAN networks toVirtual Server/Mapped IP travelling through the device." Option: specify the monitoring functions on packets from WAN networks toVirtual Server/Mapped IP travelling through the Security Bandwidth Manager." Configure: modify settings or remove incoming policy." Move: this sets the priority of the policies, number 1 being the highest priority.Descriptions for Policy figures:Figure Name DescriptionPermitBlockLogStatisticsScheduleAlarmThresholdQoSPermit the specified packets from WAN to LAN.Block the specified packets from WAN network toLAN network.Traffic and event log function is enabled.Flow statistics function is enabled.The automatic execution function in Schedule tablehas been enabled.Traffic and event alarm function is enabled.QoS function is enabled.
Page 1 and 2:
AirLive RS-1000Security Bandwidth M
Page 3 and 4:
Software Update43Interface 44Addres
Page 5 and 6:
Event Alarm151Accounting Report 154
Page 7 and 8:
Multiple NAT Multiple NAT allows lo
Page 9 and 10:
Changing the Main/Sub-Administrator
Page 11 and 12:
Removing a Sub AdministratorStep 1.
Page 13 and 14:
Exporting Security Bandwidth Manage
Page 15 and 16:
Restoring Factory Default SettingsS
Page 17 and 18:
Web Manager (WAN Interface) (Remote
Page 19 and 20:
To-Bandwidth Manager Packets LogOnc
Page 21 and 22:
Date/TimeSynchronizing the Bandwidt
Page 23 and 24:
Permitted IPsOnly the authorized IP
Page 25 and 26:
Modify Permitted IP AddressStep 1.
Page 27 and 28:
Multiple NATMultiple NAT allows loc
Page 29 and 30:
Add Multiple NATStep 1. Click the A
Page 31 and 32:
Delete Multiple NATStep 1. Find the
Page 33 and 34:
" Detect ICMP Flood: Select this op
Page 35 and 36:
Route TableIn this section, the Adm
Page 37 and 38:
Modifying a Static Route:Step 1. In
Page 39 and 40:
DHCPIn the section, the Administrat
Page 41 and 42:
Adding a new Host TableSTEP 1.Selec
Page 43 and 44:
How to register:Firstly, Click Dyna
Page 45 and 46:
Modify dynamic DNSStep 1. Find the
Page 47 and 48:
LogoutStep 1. Select this option to
Page 49 and 50:
InterfaceIn this section, the Admin
Page 51 and 52:
!!46
Page 53 and 54:
48Fixed: Select this if you were gi
Page 55 and 56:
50After setting all of the paramete
Page 57 and 58:
52If you want to set up DNS Server,
Page 59 and 60: AddressThe Security Bandwidth Manag
Page 61 and 62: Adding a new LAN AddressStep 1. In
Page 63 and 64: Removing a LAN AddressStep 1. In th
Page 65 and 66: Adding a LAN GroupStep 1. In the LA
Page 67 and 68: Removing a LAN GroupStep 1. In the
Page 69 and 70: Adding a new WAN AddressStep 1. In
Page 71 and 72: Removing an WAN AddressStep 1. In t
Page 73 and 74: Adding an WAN GroupStep 1. In the W
Page 75 and 76: Removing a WAN GroupStep 1. In the
Page 77 and 78: Pre-definedEntering a Pre-defined w
Page 79 and 80: 74Use” message will appear in the
Page 81 and 82: Modifying Custom ServicesStep 1. A
Page 83 and 84: GroupAccessing the Group windowStep
Page 85 and 86: Modifying Service GroupsStep 1. In
Page 87 and 88: 82ScheduleThe Security Bandwidth Ma
Page 89 and 90: Adding a new ScheduleStep 1. Click
Page 91 and 92: Removing a ScheduleStep 1. In the S
Page 93 and 94: 88Configuration of QoSClick QoS in
Page 95 and 96: 90Modify QoSStep 1. Click QoS in th
Page 97 and 98: 92AuthenticationBy configuring the
Page 99 and 100: STEP 2.Enter the following setting
Page 101 and 102: STEP 4.When user_1 is going to acce
Page 103 and 104: OutgoingThis section describes step
Page 105 and 106: 100Adding a new Outgoing PolicyClic
Page 107 and 108: 102Modifying an Outgoing policyStep
Page 109: Removing the Outgoing PolicyStep 1.
Page 113 and 114: Adding an Incoming PolicyUnder Inco
Page 115 and 116: Modifying Incoming PolicyStep 1. In
Page 117 and 118: Removing an Incoming PolicyStep 1.
Page 119 and 120: URL BlockingThe Administrator may s
Page 121 and 122: Adding a URL Blocking policyStep 1.
Page 123 and 124: Removing a URL Blocking policyStep
Page 125 and 126: Virtual ServerThe Security Bandwidt
Page 127 and 128: Mapped IPInternal private IP addres
Page 129 and 130: Modifying a Mapped IPStep 1. In the
Page 131 and 132: Virtual ServerVirtual server is a o
Page 133 and 134: Modifying a Virtual Server IP Addre
Page 135 and 136: Setting the Virtual Server’s serv
Page 137 and 138: Modifying the Virtual Server config
Page 139 and 140: LogThe Security Bandwidth Manager s
Page 141 and 142: Downloading the Traffic LogsThe Adm
Page 143 and 144: Event LogWhen the Security Bandwidt
Page 145 and 146: Clearing the Event LogsThe Administ
Page 147 and 148: Download LogsStep 1. Click Log in t
Page 149 and 150: Log BackupStep 1. Click Log $Log Ba
Page 151 and 152: Disable Log Mail Support & Syslog M
Page 153 and 154: Traffic AlarmIn control policies, t
Page 155 and 156: Clearing the Traffic Alarm LogsStep
Page 157 and 158: Downloading the Event Alarm LogsThe
Page 159 and 160: Accounting ReportAccounting Report
Page 161 and 162:
Outbound Accounting ReportStep 1. C
Page 163 and 164:
Outbound Destination IP Accounting
Page 165 and 166:
Outbound Service Accounting ReportS
Page 167 and 168:
InboundStep 1. Click Service in the
Page 169 and 170:
Inbound Destination IP Accounting R
Page 171 and 172:
Inbound Service Accounting ReportSe
Page 173 and 174:
StatisticsIn this chapter, the Admi
Page 175 and 176:
WAN StatisticsStep 1. Click Statist
Page 177 and 178:
Entering the Policy SatisticsStep 1
Page 179 and 180:
Interface StatusEntering the Interf
Page 181 and 182:
ARP TableEntering the ARP Table win
Page 183 and 184:
Setup ExamplesExample 1: Allow the
Page 185 and 186:
180
Page 187 and 188:
Step 8. Go to the Incoming window u
Page 189 and 190:
Step 6. In the Add New Policy windo
Page 191 and 192:
Step 7. Click the New Entry button.
Page 193 and 194:
Install a server inside the LAN net
Page 195 and 196:
Step 9. After adding new server IP,
Page 197:
Step 14. In the Add New Policy wind
show all

RS-1000 Manual - kamery airlive airlivecam

Create successful ePaper yourself

Delete template?

Save as template?