RS-1000 Manual - kamery airlive airlivecam
RS-1000 Manual - kamery airlive airlivecam RS-1000 Manual - kamery airlive airlivecam
99Descriptions for Policy figures:Figure Name DescriptionPermitPermit the specified packets from LAN network toWAN network.BlockBlock the specified packets from LAN network toWAN network.Log Traffic and event log function is enabled.Statistics Flow statistics function is enabled.ScheduleThe automatic execution function in Schedule tablehas been enabled.AlarmThresholdTraffic and event alarm function is enabled.QoS QoS function is enabled.Remarks:To view the traffic and event log of the system, click Log function in the menubar on the left hand side.To view the alarm records of the system, click Alarm function in the menu baron the left hand side.To view the statistics of the system, click Statistics function in the menu baron the left hand side.Security Bandwidth Manager can execute the schedule function automaticallyin a certain time and range. To modify the schedule, click the Schedule function inthe menu baron the left hand side.Security Bandwidth Manager can execute the QoS function functionautomatically. To modify the QoS, click the QoS function in the menu bar on theleft hand side.
100Adding a new Outgoing PolicyClick on the New Entry button and the Add New Policy window will appear.Figure7-2Add a new Outgoing PolicySource Address: Select the name of the LAN network from the drop down list. The dropdown list contains the names of all LAN networks defined in the LAN section of the Addressmenu. To create a new source address, please go to the LAN section under the Addressmenu.Destination Address: Select the name of the WANnetwork from the drop down list. The dropdown list contains the names of all WANnetworks defined in the WANsection of the Addresswindow. To create a new destination address, please go to the WANsection under theAddress menu.Service: Specified services provided by WANnetwork servers. These aresrvices/application that are allowed to pass from the LAN network to the WANnetwork.Choose ANY for all services.Action: Select Permit or Deny from the drop down list to allow or reject the packets travellingbetween the source network and the destination network.Logging: Select Enable to enable flow monitoring.Statistics: Select Enable to enable flow statistics.Schedule: Select the pre-defined schedule name from the pull-up menu. The policy will beexecuted in the specific time slot automatically.
- Page 53 and 54: 48Fixed: Select this if you were gi
- Page 55 and 56: 50After setting all of the paramete
- Page 57 and 58: 52If you want to set up DNS Server,
- Page 59 and 60: AddressThe Security Bandwidth Manag
- Page 61 and 62: Adding a new LAN AddressStep 1. In
- Page 63 and 64: Removing a LAN AddressStep 1. In th
- Page 65 and 66: Adding a LAN GroupStep 1. In the LA
- Page 67 and 68: Removing a LAN GroupStep 1. In the
- Page 69 and 70: Adding a new WAN AddressStep 1. In
- Page 71 and 72: Removing an WAN AddressStep 1. In t
- Page 73 and 74: Adding an WAN GroupStep 1. In the W
- Page 75 and 76: Removing a WAN GroupStep 1. In the
- Page 77 and 78: Pre-definedEntering a Pre-defined w
- Page 79 and 80: 74Use” message will appear in the
- Page 81 and 82: Modifying Custom ServicesStep 1. A
- Page 83 and 84: GroupAccessing the Group windowStep
- Page 85 and 86: Modifying Service GroupsStep 1. In
- Page 87 and 88: 82ScheduleThe Security Bandwidth Ma
- Page 89 and 90: Adding a new ScheduleStep 1. Click
- Page 91 and 92: Removing a ScheduleStep 1. In the S
- Page 93 and 94: 88Configuration of QoSClick QoS in
- Page 95 and 96: 90Modify QoSStep 1. Click QoS in th
- Page 97 and 98: 92AuthenticationBy configuring the
- Page 99 and 100: STEP 2.Enter the following setting
- Page 101 and 102: STEP 4.When user_1 is going to acce
- Page 103: OutgoingThis section describes step
- Page 107 and 108: 102Modifying an Outgoing policyStep
- Page 109 and 110: Removing the Outgoing PolicyStep 1.
- Page 111 and 112: 106fourth column is the Alarm Thres
- Page 113 and 114: Adding an Incoming PolicyUnder Inco
- Page 115 and 116: Modifying Incoming PolicyStep 1. In
- Page 117 and 118: Removing an Incoming PolicyStep 1.
- Page 119 and 120: URL BlockingThe Administrator may s
- Page 121 and 122: Adding a URL Blocking policyStep 1.
- Page 123 and 124: Removing a URL Blocking policyStep
- Page 125 and 126: Virtual ServerThe Security Bandwidt
- Page 127 and 128: Mapped IPInternal private IP addres
- Page 129 and 130: Modifying a Mapped IPStep 1. In the
- Page 131 and 132: Virtual ServerVirtual server is a o
- Page 133 and 134: Modifying a Virtual Server IP Addre
- Page 135 and 136: Setting the Virtual Server’s serv
- Page 137 and 138: Modifying the Virtual Server config
- Page 139 and 140: LogThe Security Bandwidth Manager s
- Page 141 and 142: Downloading the Traffic LogsThe Adm
- Page 143 and 144: Event LogWhen the Security Bandwidt
- Page 145 and 146: Clearing the Event LogsThe Administ
- Page 147 and 148: Download LogsStep 1. Click Log in t
- Page 149 and 150: Log BackupStep 1. Click Log $Log Ba
- Page 151 and 152: Disable Log Mail Support & Syslog M
- Page 153 and 154: Traffic AlarmIn control policies, t
99Descriptions for Policy figures:Figure Name DescriptionPermitPermit the specified packets from LAN network toWAN network.BlockBlock the specified packets from LAN network toWAN network.Log Traffic and event log function is enabled.Statistics Flow statistics function is enabled.ScheduleThe automatic execution function in Schedule tablehas been enabled.AlarmThresholdTraffic and event alarm function is enabled.QoS QoS function is enabled.Remarks:To view the traffic and event log of the system, click Log function in the menubar on the left hand side.To view the alarm records of the system, click Alarm function in the menu baron the left hand side.To view the statistics of the system, click Statistics function in the menu baron the left hand side.Security Bandwidth Manager can execute the schedule function automaticallyin a certain time and range. To modify the schedule, click the Schedule function inthe menu baron the left hand side.Security Bandwidth Manager can execute the QoS function functionautomatically. To modify the QoS, click the QoS function in the menu bar on theleft hand side.