About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
System Installation with ContentServer 1000 and 2000 Series Connecting the ContentDirectors to a Network Switch This section provides instructions for connecting the ContentDirectors to the 1GbE network switches. Refer to the following figure when connecting a ContentDirector to a network switch. NOTE: The network switches to which you connect the ContentDirector may differ from those shown below, however, the same port numbers should be used. IMPORTANT: Make sure to use only MediaGrid-qualified switches in your MediaGrid system. To find out if a switch is MediaGrid-qualified, contact your Harmonic representative. First Network Switch or Switch Module Second Network Switch or Switch Module ContentDirector Figure 35. ContentDirectors and Network Switch Connections To connect the ContentDirectors to network switches: 1. Starting with the first ContentDirector, connect a yellow Ethernet cable to NIC 3. Connect the other end of the cable to port 45 on the second network switch. 2. Connect a black Ethernet cable to NIC 2 on the ContentDirector. Connect the other end of the cable to port 45 on the first network switch. 3. Connect a white Ethernet cable to NIC 0 on the ContentDirector. Connect the other end of the cable to port 41 on the first network switch. 4. Connect a blue Ethernet cable to NIC 1 on the ContentDirector. Connect the other end of the cable to port 41 on the second network switch. 5. Connect the remaining ContentDirectors in the same manner, continuing from port 42 on the network switches. 74 Installation and Configuration Guide
System Installation with ContentServer 1000 and 2000 Series Connecting Network Switches to the Client Network: One-rack System This section provides instructions for connecting the network switches in a one-rack Omneon MediaGrid system to the client network. Refer to Connecting Network Switches to the Client Network: Two-rack System for other connection options. Refer to the following figure when connecting the network switches to the client network. To Client Network Figure 36. Network Switches and Client Network Connections To connect the network switches to the client network: 1. Connect CX4 cables to Port A2 and to Port A3 on the first switch. Push in the locking device on both ends of the CX4 cable to ensure the cable connector is locked in place. Connect the other end of each cable to the client network. NOTE: Use ports A1 and A4 on the switch for fiber optic-cable connections. 2. Connect CX4 cables to Port A2 and to Port A3 on the second switch. Push in the locking device on both ends of the CX4 cable to ensure the cable connector is locked in place. Connect the other end of each cable to the client network. 3. Continue with Connecting the Power Cables to complete the hardware installation. First Switch Second Switch Omneon, Now Part of Harmonic 75
- Page 47 and 48: 16 5x(2+1)+1 500 GB 5 TB 16 5x(2+1)
- Page 49 and 50: System Installation with ContentSer
- Page 51 and 52: System Installation with ContentSer
- Page 53 and 54: System Installation with ContentSer
- Page 55 and 56: System Installation with ContentSer
- Page 57 and 58: Figure 10. ContentServer 3000 and 1
- Page 59 and 60: System Installation with ContentSer
- Page 61 and 62: System Installation with ContentSer
- Page 63 and 64: 10GbE Switch First Switch Second Sw
- Page 65 and 66: Module A To Client Network 10-GbE S
- Page 67 and 68: Connecting the ContentBridge System
- Page 69 and 70: Connecting the ContentDirectors Sys
- Page 71 and 72: Configuring a Stretch Cluster Syste
- Page 73 and 74: 10 GbE Module 1 GbE Module Public V
- Page 75 and 76: System Installation with ContentSer
- Page 77 and 78: CHAPTER 2 System Installation with
- Page 79 and 80: ContentBridge (optional) SystemMana
- Page 81 and 82: • The VLAN name and ID for the su
- Page 83 and 84: The following software installation
- Page 85 and 86: Before You Begin System Installatio
- Page 87 and 88: To rack mount an Omneon MediaGrid:
- Page 89 and 90: Figure 26. Rack Mounting the Conten
- Page 91 and 92: Installing the ContentServer Disk D
- Page 93 and 94: System Installation with ContentSer
- Page 95 and 96: 2 1 2 1 ID ID Figure 32. ContentSer
- Page 97: System Installation with ContentSer
- Page 101 and 102: System Installation with ContentSer
- Page 103 and 104: 2. Continue connecting any remainin
- Page 105 and 106: System Installation with ContentSer
- Page 107 and 108: CHAPTER 3 System Configuration This
- Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
- Page 111 and 112: System Configuration 4. If you are
- Page 113 and 114: 6. Apply power to the ContentServer
- Page 115 and 116: Notes on Active Directory Configura
- Page 117 and 118: Follow the prompts to initialize th
- Page 119 and 120: Joining an Omneon MediaGrid Cluster
- Page 121 and 122: 1. From your SSH terminal, edit /et
- Page 123 and 124: A list of users in the domain displ
- Page 125 and 126: System Configuration 1. After confi
- Page 127 and 128: 4. Type the following commands to r
- Page 129 and 130: The expected result is: Domain=[SNV
- Page 131 and 132: System Configuration This mount poi
- Page 133 and 134: System Configuration c. Replace wi
- Page 135 and 136: Modify the file as follows: System
- Page 137 and 138: Omneon MediaGrid name ContentDirect
- Page 139 and 140: Editing the LDAP Configuration File
- Page 141 and 142: System Configuration 4. Create a Sa
- Page 143 and 144: Modify the file as follows: System
- Page 145 and 146: Figure 43. Server Admin Open Direct
- Page 147 and 148: The following is a sample output fr
System Installation with ContentServer 1000 and 2000 Series<br />
Connecting Network Switches to the Client Network: One-rack<br />
System<br />
This section provides instructions for connecting the network switches in a one-rack <strong>Omneon</strong><br />
<strong>MediaGrid</strong> system to the client network. Refer to Connecting Network Switches to the Client<br />
Network: Two-rack System for other connection options.<br />
Refer to the following figure when connecting the network switches to the client network.<br />
To Client Network<br />
Figure 36. Network Switches and Client Network Connections<br />
To connect the network switches to the client network:<br />
1. Connect CX4 cables to Port A2 and to Port A3 on the first switch. Push in the locking device on both<br />
ends of the CX4 cable to ensure the cable connector is locked in place. Connect the other end of each<br />
cable to the client network.<br />
NOTE: Use ports A1 and A4 on the switch for fiber optic-cable connections.<br />
2. Connect CX4 cables to Port A2 and to Port A3 on the second switch. Push in the locking device on<br />
both ends of the CX4 cable to ensure the cable connector is locked in place. Connect the other end of<br />
each cable to the client network.<br />
3. Continue with Connecting the Power Cables to complete the hardware installation.<br />
First Switch<br />
Second Switch<br />
<strong>Omneon</strong>, Now Part of <strong>Harmonic</strong> 75