About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
System Installation with ContentServer 1000 and 2000 Series About Mixed ContentServer 1042 (1U) and 2122/2124 (2U) Configurations Clients can utilize the full bandwidth and storage provided by all ContentServers in a mixed-server configuration (ContentServers 1042 and ContentServers 2122/2124 in the same Omneon MediaGrid system). In order for a mixed server configuration to function properly, you must make sure the system is balanced on a regular basis by using the balance scheduler feature provided in SystemManager version 5.15 and later. Scheduled balancing ensures that disk space is balanced across a cluster. To enable and configure the balance scheduler, refer to “Enabling and Configuring Scheduled Balancing” in the Omneon SystemManager User Guide. Connecting a SystemManager to a Network Switch This section provides instructions for connecting the SystemManager to the 1GbE network switch. See the Omneon SystemManager Installation Guide for details about the SystemManager platform included in your Omneon MediaGrid system. IMPORTANT: vDHCP must be disabled in the SystemManager application before connecting the SystemManager device to the 1GbE network switch. Refer to “Disabling vDHCP” in the Omneon SystemManager User Guide for instructions. IMPORTANT: Make sure to use only MediaGrid-qualified switches in your MediaGrid system. To find out if a switch is MediaGrid-qualified, contact your Harmonic representative. First Network Switch SystemManager Rear Panel Gb 1 Gb 2 Figure 33. SystemManager and Network Switch Connection To connect a SystemManger to a network switch: 1. Connect a CAT-6 Ethernet cable to the SystemManager, as shown in Figure 33. 2. Connect the other end of the cable to port 44 on the first network switch. 72 Installation and Configuration Guide
System Installation with ContentServer 1000 and 2000 Series Connecting a ContentBridge 2010B/2010C to the Omneon MediaGrid Network Switch This section provides instructions for connecting an optional High Bandwidth ContentBridge. NOTE: The switch shown in Figure 34 is provided as an example only. Your switch may vary from the one shown. IMPORTANT: Make sure to use only MediaGrid-qualified switches in your MediaGrid system. To find out if a switch is MediaGrid-qualified, contact your Harmonic representative. Refer to Figure 34 when connecting a ContentBridge 2010B/2010C to a customer switch. NOTE: The ContentBridge 2010B/2010 can be on either the Public VLAN or the client VLAN. However, if you wish to use the Configuration Assistant to configure the ContentBridge, it must on the Public VLAN. If you are using a ContentBridge 1000B, it must be on the Public VLAN without exception. Customer Core Switch ContentBridge To Omneon MediaGrid Network Figure 34. ContentBridge and Omneon MediaGrid Network Switch Connections To connect a ContentBridge to the Omneon MediaGrid network switch: 1. Connect the appropriate network cable (CX4 or MMF) to the 10GbE port on the ContentBridge. 2. Connect the other end of the cable to an available port on the customer core switch. 3. Connect the customer core switch to the Omneon MediaGrid network switches. Refer to Connecting Network Switches to the Client Network: One-rack System or Connecting Network Switches to the Client Network: Two-rack System, depending on the system setup. Omneon, Now Part of Harmonic 73
- Page 45 and 46: Public VLAN Private VLAN 1 Private
- Page 47 and 48: 16 5x(2+1)+1 500 GB 5 TB 16 5x(2+1)
- Page 49 and 50: System Installation with ContentSer
- Page 51 and 52: System Installation with ContentSer
- Page 53 and 54: System Installation with ContentSer
- Page 55 and 56: System Installation with ContentSer
- Page 57 and 58: Figure 10. ContentServer 3000 and 1
- Page 59 and 60: System Installation with ContentSer
- Page 61 and 62: System Installation with ContentSer
- Page 63 and 64: 10GbE Switch First Switch Second Sw
- Page 65 and 66: Module A To Client Network 10-GbE S
- Page 67 and 68: Connecting the ContentBridge System
- Page 69 and 70: Connecting the ContentDirectors Sys
- Page 71 and 72: Configuring a Stretch Cluster Syste
- Page 73 and 74: 10 GbE Module 1 GbE Module Public V
- Page 75 and 76: System Installation with ContentSer
- Page 77 and 78: CHAPTER 2 System Installation with
- Page 79 and 80: ContentBridge (optional) SystemMana
- Page 81 and 82: • The VLAN name and ID for the su
- Page 83 and 84: The following software installation
- Page 85 and 86: Before You Begin System Installatio
- Page 87 and 88: To rack mount an Omneon MediaGrid:
- Page 89 and 90: Figure 26. Rack Mounting the Conten
- Page 91 and 92: Installing the ContentServer Disk D
- Page 93 and 94: System Installation with ContentSer
- Page 95: 2 1 2 1 ID ID Figure 32. ContentSer
- Page 99 and 100: System Installation with ContentSer
- Page 101 and 102: System Installation with ContentSer
- Page 103 and 104: 2. Continue connecting any remainin
- Page 105 and 106: System Installation with ContentSer
- Page 107 and 108: CHAPTER 3 System Configuration This
- Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
- Page 111 and 112: System Configuration 4. If you are
- Page 113 and 114: 6. Apply power to the ContentServer
- Page 115 and 116: Notes on Active Directory Configura
- Page 117 and 118: Follow the prompts to initialize th
- Page 119 and 120: Joining an Omneon MediaGrid Cluster
- Page 121 and 122: 1. From your SSH terminal, edit /et
- Page 123 and 124: A list of users in the domain displ
- Page 125 and 126: System Configuration 1. After confi
- Page 127 and 128: 4. Type the following commands to r
- Page 129 and 130: The expected result is: Domain=[SNV
- Page 131 and 132: System Configuration This mount poi
- Page 133 and 134: System Configuration c. Replace wi
- Page 135 and 136: Modify the file as follows: System
- Page 137 and 138: Omneon MediaGrid name ContentDirect
- Page 139 and 140: Editing the LDAP Configuration File
- Page 141 and 142: System Configuration 4. Create a Sa
- Page 143 and 144: Modify the file as follows: System
- Page 145 and 146: Figure 43. Server Admin Open Direct
System Installation with ContentServer 1000 and 2000 Series<br />
<strong>About</strong> Mixed ContentServer 1042 (1U) and 2122/2124 (2U)<br />
Configurations<br />
Clients can utilize the full bandwidth and storage provided by all ContentServers in a mixed-server<br />
configuration (ContentServers 1042 and ContentServers 2122/2124 in the same <strong>Omneon</strong> <strong>MediaGrid</strong><br />
system). In order for a mixed server configuration to function properly, you must make sure the<br />
system is balanced on a regular basis by using the balance scheduler feature provided in<br />
SystemManager version 5.15 and later. Scheduled balancing ensures that disk space is balanced across<br />
a cluster. To enable and configure the balance scheduler, refer to “Enabling and Configuring<br />
Scheduled Balancing” in the <strong>Omneon</strong> SystemManager User Guide.<br />
Connecting a SystemManager to a Network Switch<br />
This section provides instructions for connecting the SystemManager to the 1GbE network switch.<br />
See the <strong>Omneon</strong> SystemManager Installation Guide for details about the SystemManager platform included<br />
in your <strong>Omneon</strong> <strong>MediaGrid</strong> system.<br />
IMPORTANT: vDHCP must be disabled in the SystemManager application before connecting the<br />
SystemManager device to the 1GbE network switch. Refer to “Disabling vDHCP” in the <strong>Omneon</strong><br />
SystemManager User Guide for instructions.<br />
IMPORTANT: Make sure to use only <strong>MediaGrid</strong>-qualified switches in your <strong>MediaGrid</strong> system. To find out if a<br />
switch is <strong>MediaGrid</strong>-qualified, contact your <strong>Harmonic</strong> representative.<br />
First Network Switch<br />
SystemManager Rear Panel<br />
Gb 1 Gb 2<br />
Figure 33. SystemManager and Network Switch Connection<br />
To connect a SystemManger to a network switch:<br />
1. Connect a CAT-6 Ethernet cable to the SystemManager, as shown in Figure 33.<br />
2. Connect the other end of the cable to port 44 on the first network switch.<br />
72 Installation and Configuration Guide