About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
System Installation with ContentServer 1000 and 2000 Series To connect the ContentServers to network switches: 1. Starting with the bottom ContentServer, connect a white CAT-6 Ethernet cable to the left Ethernet port. Connect the other end of the cable to port 1 on the first network switch. 2. Connect a blue Ethernet cable to the right Ethernet port on the ContentServer. Connect the other end of the cable to port 1 on the second network switch. 1. Connect the second ContentServer to port two on the network switches: a white Ethernet cable from the ContentServer left port to port 2 on the second network switch; a blue cable from the right port to port 2 on the first network switch. 2. Continue connecting the remaining ContentServers in the same manner, utilizing ports 3-39 on the network switches, as needed. Connecting the ContentServer 2122/2124 to Network Switches Refer to Figure 32 when connecting a ContentServer 2122/2124 to a network switch. Figure 32 shows both a ContentServer 2124 and ContentServer 2122 connected to two network switches. NOTE: The switch shown in Figure 32 is provided as an example only. Your switch may vary from the one shown. IMPORTANT: Make sure to use only MediaGrid-qualified switches in your MediaGrid system. To find out if a switch is MediaGrid-qualified, contact your Harmonic representative. 70 Installation and Configuration Guide
2 1 2 1 ID ID Figure 32. ContentServers and Network Switch Connections To connect the ContentServers to network switches: S tatus S tatus System Installation with ContentServer 1000 and 2000 Series 1. Starting with the bottom ContentServer 2122, connect a white CAT-6 Ethernet cable to the left Ethernet port (NIC 0). Connect the other end of the cable to port 1 on the first network switch. 2. Connect a blue Ethernet cable to the right Ethernet port (NIC 1) on the ContentServer 2122. Connect the other end of the cable to port 1 on the second network switch. 3. Connect the second ContentServer (ContentServer 2124) to ports two and three on the network switches: a white Ethernet cable from the ContentServer left port (NIC 0) to port 2 on the first network switch; a blue cable from the right port (NIC 1) to port 2 on the second network switch; a white cable from NIC 2 to port 3 on the first network switch; a blue cable from NIC 3 to port three on the second network switch. 4. Continue connecting the remaining ContentServers in the same manner, utilizing ports 3-39 on the network switches, as needed. Omneon, Now Part of Harmonic 71 NIC 0 NIC 1 NIC 0 NIC 1 NIC 3 NIC 2 First Network Switch Second Network Switch ContentServer 2124 ContentServer 2122
- Page 43 and 44: Public VLAN Private VLAN 1 Private
- Page 45 and 46: Public VLAN Private VLAN 1 Private
- Page 47 and 48: 16 5x(2+1)+1 500 GB 5 TB 16 5x(2+1)
- Page 49 and 50: System Installation with ContentSer
- Page 51 and 52: System Installation with ContentSer
- Page 53 and 54: System Installation with ContentSer
- Page 55 and 56: System Installation with ContentSer
- Page 57 and 58: Figure 10. ContentServer 3000 and 1
- Page 59 and 60: System Installation with ContentSer
- Page 61 and 62: System Installation with ContentSer
- Page 63 and 64: 10GbE Switch First Switch Second Sw
- Page 65 and 66: Module A To Client Network 10-GbE S
- Page 67 and 68: Connecting the ContentBridge System
- Page 69 and 70: Connecting the ContentDirectors Sys
- Page 71 and 72: Configuring a Stretch Cluster Syste
- Page 73 and 74: 10 GbE Module 1 GbE Module Public V
- Page 75 and 76: System Installation with ContentSer
- Page 77 and 78: CHAPTER 2 System Installation with
- Page 79 and 80: ContentBridge (optional) SystemMana
- Page 81 and 82: • The VLAN name and ID for the su
- Page 83 and 84: The following software installation
- Page 85 and 86: Before You Begin System Installatio
- Page 87 and 88: To rack mount an Omneon MediaGrid:
- Page 89 and 90: Figure 26. Rack Mounting the Conten
- Page 91 and 92: Installing the ContentServer Disk D
- Page 93: System Installation with ContentSer
- Page 97 and 98: System Installation with ContentSer
- Page 99 and 100: System Installation with ContentSer
- Page 101 and 102: System Installation with ContentSer
- Page 103 and 104: 2. Continue connecting any remainin
- Page 105 and 106: System Installation with ContentSer
- Page 107 and 108: CHAPTER 3 System Configuration This
- Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
- Page 111 and 112: System Configuration 4. If you are
- Page 113 and 114: 6. Apply power to the ContentServer
- Page 115 and 116: Notes on Active Directory Configura
- Page 117 and 118: Follow the prompts to initialize th
- Page 119 and 120: Joining an Omneon MediaGrid Cluster
- Page 121 and 122: 1. From your SSH terminal, edit /et
- Page 123 and 124: A list of users in the domain displ
- Page 125 and 126: System Configuration 1. After confi
- Page 127 and 128: 4. Type the following commands to r
- Page 129 and 130: The expected result is: Domain=[SNV
- Page 131 and 132: System Configuration This mount poi
- Page 133 and 134: System Configuration c. Replace wi
- Page 135 and 136: Modify the file as follows: System
- Page 137 and 138: Omneon MediaGrid name ContentDirect
- Page 139 and 140: Editing the LDAP Configuration File
- Page 141 and 142: System Configuration 4. Create a Sa
- Page 143 and 144: Modify the file as follows: System
System Installation with ContentServer 1000 and 2000 Series<br />
To connect the ContentServers to network switches:<br />
1. Starting with the bottom ContentServer, connect a white CAT-6 Ethernet cable to the left Ethernet<br />
port. Connect the other end of the cable to port 1 on the first network switch.<br />
2. Connect a blue Ethernet cable to the right Ethernet port on the ContentServer. Connect the other<br />
end of the cable to port 1 on the second network switch.<br />
1. Connect the second ContentServer to port two on the network switches: a white Ethernet cable from<br />
the ContentServer left port to port 2 on the second network switch; a blue cable from the right port to<br />
port 2 on the first network switch.<br />
2. Continue connecting the remaining ContentServers in the same manner, utilizing ports 3-39 on the<br />
network switches, as needed.<br />
Connecting the ContentServer 2122/2124 to Network Switches<br />
Refer to Figure 32 when connecting a ContentServer 2122/2124 to a network switch. Figure 32<br />
shows both a ContentServer 2124 and ContentServer 2122 connected to two network switches.<br />
NOTE: The switch shown in Figure 32 is provided as an example only. Your switch may vary from the one<br />
shown.<br />
IMPORTANT: Make sure to use only <strong>MediaGrid</strong>-qualified switches in your <strong>MediaGrid</strong> system. To find out if a<br />
switch is <strong>MediaGrid</strong>-qualified, contact your <strong>Harmonic</strong> representative.<br />
70 Installation and Configuration Guide