About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
System Installation with ContentServer 1000 and 2000 Series Installing the ContentServer 2122/2124 Disk Drives To install the disk drives: 1. Remove the bezel from the ContentServer by turning the two captive thumb screws counterclockwise until the spring releases the screws from the chassis. Then pull the bezel directly away from the chassis. 2. Unpack a disk drive. 3. Insert the drive by sliding the drive into the drive enclosure until it provides resistance. Push the lever closed while pressing on the right side of the carrier until the carrier clicks into place. Figure 30. Disk Drive Installation 4. Replace the front bezel by aligning the two tabs (on the outside of the thumb screws) with the two compatible slots on the front of the unit. Evenly press the bezel into place. 5. Install the remaining drives, leaving no empty slots. WARNING: The ContentServer 2122/2124 is heavy with the drives installed. To eliminate any possibility of tipping over, do not slide more than one server out at a time. Always ensure that the equipment rack is secured to the floor or wall. 68 Installation and Configuration Guide
System Installation with ContentServer 1000 and 2000 Series Connecting the MediaGrid System Components The following section provides instructions for connecting the Omneon MediaGrid storage system components. It is recommended that you connect the blue-colored cables to the device ports on the left side (as seen from the back) and the white-colored cables to the ports on the right side. Tip: Once you have completed the connections, group the cables and then secure them to the rear side rails. Connecting the ContentServer 1042 to Network Switches This section provides instructions for connecting two ContentServers to the 1GbE network switches. Refer to the following figure when connecting a ContentServer 1042 to a network switch. Figure 31 shows the first two connections, including two ContentServers 1042. NOTE: The switch shown in Figure 31 is provided as an example only. Your switch may vary from the one shown. IMPORTANT: Make sure to use only MediaGrid-qualified switches in your MediaGrid system. To find out if a switch is MediaGrid-qualified, contact your Harmonic representative. Figure 31. ContentServers and Network Switch Connections First Network Switch Second Network Switch Second ContentServer Omneon, Now Part of Harmonic 69 l 0 First ContentServer l 0
- Page 41 and 42: • Cluster names and device names
- Page 43 and 44: Public VLAN Private VLAN 1 Private
- Page 45 and 46: Public VLAN Private VLAN 1 Private
- Page 47 and 48: 16 5x(2+1)+1 500 GB 5 TB 16 5x(2+1)
- Page 49 and 50: System Installation with ContentSer
- Page 51 and 52: System Installation with ContentSer
- Page 53 and 54: System Installation with ContentSer
- Page 55 and 56: System Installation with ContentSer
- Page 57 and 58: Figure 10. ContentServer 3000 and 1
- Page 59 and 60: System Installation with ContentSer
- Page 61 and 62: System Installation with ContentSer
- Page 63 and 64: 10GbE Switch First Switch Second Sw
- Page 65 and 66: Module A To Client Network 10-GbE S
- Page 67 and 68: Connecting the ContentBridge System
- Page 69 and 70: Connecting the ContentDirectors Sys
- Page 71 and 72: Configuring a Stretch Cluster Syste
- Page 73 and 74: 10 GbE Module 1 GbE Module Public V
- Page 75 and 76: System Installation with ContentSer
- Page 77 and 78: CHAPTER 2 System Installation with
- Page 79 and 80: ContentBridge (optional) SystemMana
- Page 81 and 82: • The VLAN name and ID for the su
- Page 83 and 84: The following software installation
- Page 85 and 86: Before You Begin System Installatio
- Page 87 and 88: To rack mount an Omneon MediaGrid:
- Page 89 and 90: Figure 26. Rack Mounting the Conten
- Page 91: Installing the ContentServer Disk D
- Page 95 and 96: 2 1 2 1 ID ID Figure 32. ContentSer
- Page 97 and 98: System Installation with ContentSer
- Page 99 and 100: System Installation with ContentSer
- Page 101 and 102: System Installation with ContentSer
- Page 103 and 104: 2. Continue connecting any remainin
- Page 105 and 106: System Installation with ContentSer
- Page 107 and 108: CHAPTER 3 System Configuration This
- Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
- Page 111 and 112: System Configuration 4. If you are
- Page 113 and 114: 6. Apply power to the ContentServer
- Page 115 and 116: Notes on Active Directory Configura
- Page 117 and 118: Follow the prompts to initialize th
- Page 119 and 120: Joining an Omneon MediaGrid Cluster
- Page 121 and 122: 1. From your SSH terminal, edit /et
- Page 123 and 124: A list of users in the domain displ
- Page 125 and 126: System Configuration 1. After confi
- Page 127 and 128: 4. Type the following commands to r
- Page 129 and 130: The expected result is: Domain=[SNV
- Page 131 and 132: System Configuration This mount poi
- Page 133 and 134: System Configuration c. Replace wi
- Page 135 and 136: Modify the file as follows: System
- Page 137 and 138: Omneon MediaGrid name ContentDirect
- Page 139 and 140: Editing the LDAP Configuration File
- Page 141 and 142: System Configuration 4. Create a Sa
System Installation with ContentServer 1000 and 2000 Series<br />
Connecting the <strong>MediaGrid</strong> System Components<br />
The following section provides instructions for connecting the <strong>Omneon</strong> <strong>MediaGrid</strong> storage system<br />
components. It is recommended that you connect the blue-colored cables to the device ports on the<br />
left side (as seen from the back) and the white-colored cables to the ports on the right side.<br />
Tip: Once you have completed the connections, group the cables and then secure them to the rear side rails.<br />
Connecting the ContentServer 1042 to Network Switches<br />
This section provides instructions for connecting two ContentServers to the 1GbE network switches.<br />
Refer to the following figure when connecting a ContentServer 1042 to a network switch. Figure 31<br />
shows the first two connections, including two ContentServers 1042.<br />
NOTE: The switch shown in Figure 31 is provided as an example only. Your switch may vary from the one<br />
shown.<br />
IMPORTANT: Make sure to use only <strong>MediaGrid</strong>-qualified switches in your <strong>MediaGrid</strong> system. To find out if a<br />
switch is <strong>MediaGrid</strong>-qualified, contact your <strong>Harmonic</strong> representative.<br />
Figure 31. ContentServers and Network Switch Connections<br />
First Network Switch<br />
Second Network Switch<br />
Second ContentServer<br />
<strong>Omneon</strong>, Now Part of <strong>Harmonic</strong> 69<br />
l<br />
0<br />
First ContentServer<br />
l<br />
0