About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
System Installation with ContentServer 3000 Series Connecting the ContentDirectors IMPORTANT: Ports 1-4 on switch modules C and D are reserved for ContentDirector private interface (ports 2 and 3) connections only. 1. To connect the ContentDirectors: Connect the ContentDirector private interfaces (ports 2 and 3) to the switch as follows: a. Connect port 2 on the first ContentDirector to port 1 on switch module D. b. Connect port 3 on the first ContentDirector to port 1 on switch module C. 2. Connect the ContentDirector public interfaces (ports 1 and 0) to the switch as follows: a. Connect port 1 on the first ContentDirector to port 5 on switch module C. b. Connect port 0 on the first ContentDirector to port 5 on switch module D. 3. Continue connecting any remaining ContentDirectors in the same manner, starting with port 2 on the switch for the private interfaces and port 6 on the switch for the public interfaces. Connecting the SystemManager To connect the SystemManager: Connect port 1 on the SystemManager to port 8 on switch module D. IMPORTANT: Make sure to leave a space for the SystemManager keyboard/monitor tray. It is recommended that you mount the keyboard monitor and tray 71.12 cm (28.0 in.) off the floor. This height is ideal for using the SystemManager while seated or standing. Connecting the ContentServers Complete these connections after connecting all ContentDirectors. To connect the ContentServers: 1. From the left-hand controller, connect NIC 0 to an open port on 1 GbE switch module C. This will serve as the BMC connection for this controller 2. Connect port 4 on the left-hand controller to an open port on 10 GbE switch module A. Then, connect port 5 on the left-hand controller to an open port on 10 GbE switch module A. 3. From the right-hand controller, connect NIC 0 to an open port on 1 GbE switch module D. This will serve as the BMC connection for this controller. 4. Connect port 4 on the right-hand controller to an open port on 10 GbE switch module B. Then, connect port 5 on the right-hand controller to an open port on 10 GbE switch module B. IMPORTANT: To ensure redundancy and proper failover in the event of a failure, you must connect each controller to a separate switch or switch module. 5. Continue connecting the remaining ContentServers in the same manner. 42 Installation and Configuration Guide
Connecting the ContentBridge System Installation with ContentServer 3000 Series Complete these connections if an optional ContentBridge 2010B/2010C is part of the Omneon MediaGrid system. To connect the ContentBridge: 1. Connect the 10 Gigabit Ethernet port on first ContentBridge to the first available port on either switch module A or B. 2. Continue connecting any remaining ContentBridges in the same manner. Connecting to the Client Network Depending on the type of client connection (CX4 or fiber optic), connect all module A and module cables on the network switch to the client network. Group the connections as shown in Figure 17. Connecting an Omneon MediaGrid System to a Network Switch with 1GbE Connections This section provides instructions for connecting an Omneon MediaGrid system to a network switch with all 1GbE connections. Refer to Figure 18 when connecting the system. Not all connections are shown. NOTE: The switch shown in Figure 18 is provided as an example only. Your switch may vary from the one shown. IMPORTANT: If you are supplying your own network switches, make sure to use only MediaGrid-qualified switches in your MediaGrid system. To find out if a switch is MediaGrid-qualified, contact your Harmonic representative. See the instructions following the illustration for each device’s specific port connections. Omneon, Now Part of Harmonic 43
- Page 15 and 16: Contents Introduction . . . . . . .
- Page 17 and 18: Contents Private VLANs . . . . . .
- Page 19 and 20: Contents Joining a ContentBridge 10
- Page 21 and 22: Contents About Access Control Lists
- Page 23 and 24: Contents Front Panel View . . . . .
- Page 25 and 26: Omneon MediaGrid Version 3.1.1 Intr
- Page 27 and 28: • Cluster, in the context of an O
- Page 29 and 30: Two models of ContentDirectors are
- Page 31 and 32: Keep in mind the following addition
- Page 33 and 34: 1. From Windows, click the Start bu
- Page 35 and 36: 1. Add two registry parameters to t
- Page 37 and 38: CHAPTER 1 System Installation with
- Page 39 and 40: ContentBridge (optional) SystemMana
- Page 41 and 42: • Cluster names and device names
- Page 43 and 44: Public VLAN Private VLAN 1 Private
- Page 45 and 46: Public VLAN Private VLAN 1 Private
- Page 47 and 48: 16 5x(2+1)+1 500 GB 5 TB 16 5x(2+1)
- Page 49 and 50: System Installation with ContentSer
- Page 51 and 52: System Installation with ContentSer
- Page 53 and 54: System Installation with ContentSer
- Page 55 and 56: System Installation with ContentSer
- Page 57 and 58: Figure 10. ContentServer 3000 and 1
- Page 59 and 60: System Installation with ContentSer
- Page 61 and 62: System Installation with ContentSer
- Page 63 and 64: 10GbE Switch First Switch Second Sw
- Page 65: Module A To Client Network 10-GbE S
- Page 69 and 70: Connecting the ContentDirectors Sys
- Page 71 and 72: Configuring a Stretch Cluster Syste
- Page 73 and 74: 10 GbE Module 1 GbE Module Public V
- Page 75 and 76: System Installation with ContentSer
- Page 77 and 78: CHAPTER 2 System Installation with
- Page 79 and 80: ContentBridge (optional) SystemMana
- Page 81 and 82: • The VLAN name and ID for the su
- Page 83 and 84: The following software installation
- Page 85 and 86: Before You Begin System Installatio
- Page 87 and 88: To rack mount an Omneon MediaGrid:
- Page 89 and 90: Figure 26. Rack Mounting the Conten
- Page 91 and 92: Installing the ContentServer Disk D
- Page 93 and 94: System Installation with ContentSer
- Page 95 and 96: 2 1 2 1 ID ID Figure 32. ContentSer
- Page 97 and 98: System Installation with ContentSer
- Page 99 and 100: System Installation with ContentSer
- Page 101 and 102: System Installation with ContentSer
- Page 103 and 104: 2. Continue connecting any remainin
- Page 105 and 106: System Installation with ContentSer
- Page 107 and 108: CHAPTER 3 System Configuration This
- Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
- Page 111 and 112: System Configuration 4. If you are
- Page 113 and 114: 6. Apply power to the ContentServer
- Page 115 and 116: Notes on Active Directory Configura
Connecting the ContentBridge<br />
System Installation with ContentServer 3000 Series<br />
Complete these connections if an optional ContentBridge 2010B/2010C is part of the <strong>Omneon</strong><br />
<strong>MediaGrid</strong> system.<br />
To connect the ContentBridge:<br />
1. Connect the 10 Gigabit Ethernet port on first ContentBridge to the first available port on either<br />
switch module A or B.<br />
2. Continue connecting any remaining ContentBridges in the same manner.<br />
Connecting to the Client Network<br />
Depending on the type of client connection (CX4 or fiber optic), connect all module A and module<br />
cables on the network switch to the client network. Group the connections as shown in Figure 17.<br />
Connecting an <strong>Omneon</strong> <strong>MediaGrid</strong> System to a Network Switch with<br />
1GbE Connections<br />
This section provides instructions for connecting an <strong>Omneon</strong> <strong>MediaGrid</strong> system to a network switch<br />
with all 1GbE connections. Refer to Figure 18 when connecting the system. Not all connections are<br />
shown.<br />
NOTE: The switch shown in Figure 18 is provided as an example only. Your switch may vary from the one<br />
shown.<br />
IMPORTANT: If you are supplying your own network switches, make sure to use only <strong>MediaGrid</strong>-qualified<br />
switches in your <strong>MediaGrid</strong> system. To find out if a switch is <strong>MediaGrid</strong>-qualified, contact your <strong>Harmonic</strong><br />
representative.<br />
See the instructions following the illustration for each device’s specific port connections.<br />
<strong>Omneon</strong>, Now Part of <strong>Harmonic</strong> 43