About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
System Installation with ContentServer 3000 Series 1. Connect CX4 cables to the two 10GbE ports on the back of rack two’s first switch. Connect the other end of the cables to available 10GbE ports on rack two’s switch that connects to the client network. 2. Connect CX4 cables to the two 10GbE ports on the back of rack two’s second switch. Connect the other end of the cables to available 10GbE ports on the back of rack one’s switch that connects to the client network. 3. Connect the top network switch to the client network. Connecting an Omneon MediaGrid System to a Network Switch with 10 GbE Connections IMPORTANT: If you are supplying your own network switches, make sure to use only MediaGrid-qualified switches in your MediaGrid system. To find out if a switch is MediaGrid-qualified, contact your Harmonic representative. This section provides instructions for connecting an Omneon MediaGrid system to a network switch with 10 GbE connectivity. Refer to Figure 17 when connecting the system. Not all connections are shown. NOTE: The switch shown in Figure 17 is provided as an example only. Your switch may vary from the one shown. See the instructions following the illustration for each device’s specific port connections. 40 Installation and Configuration Guide
Module A To Client Network 10-GbE SFP+ SFP+ Ports Ports 10-GbE SFP+ Ports Figure 17. Omneon MediaGrid and 10 GbE Network Switch Connections 0 1 System Installation with ContentServer 3000 Series Module C Module D 1 0 FAULT REMOVE POWER 4 5 2 3 Omneon, Now Part of Harmonic 41 Gb 1 Gb 2 1 2 First ContentDirector First ContentServer 1 0 SystemManager ContentBridge 2010B/2010C (Optional) FAULT REMOVE POWER 4 5 Module B
- Page 13 and 14: • Storage Temperature -104 °F to
- Page 15 and 16: Contents Introduction . . . . . . .
- Page 17 and 18: Contents Private VLANs . . . . . .
- Page 19 and 20: Contents Joining a ContentBridge 10
- Page 21 and 22: Contents About Access Control Lists
- Page 23 and 24: Contents Front Panel View . . . . .
- Page 25 and 26: Omneon MediaGrid Version 3.1.1 Intr
- Page 27 and 28: • Cluster, in the context of an O
- Page 29 and 30: Two models of ContentDirectors are
- Page 31 and 32: Keep in mind the following addition
- Page 33 and 34: 1. From Windows, click the Start bu
- Page 35 and 36: 1. Add two registry parameters to t
- Page 37 and 38: CHAPTER 1 System Installation with
- Page 39 and 40: ContentBridge (optional) SystemMana
- Page 41 and 42: • Cluster names and device names
- Page 43 and 44: Public VLAN Private VLAN 1 Private
- Page 45 and 46: Public VLAN Private VLAN 1 Private
- Page 47 and 48: 16 5x(2+1)+1 500 GB 5 TB 16 5x(2+1)
- Page 49 and 50: System Installation with ContentSer
- Page 51 and 52: System Installation with ContentSer
- Page 53 and 54: System Installation with ContentSer
- Page 55 and 56: System Installation with ContentSer
- Page 57 and 58: Figure 10. ContentServer 3000 and 1
- Page 59 and 60: System Installation with ContentSer
- Page 61 and 62: System Installation with ContentSer
- Page 63: 10GbE Switch First Switch Second Sw
- Page 67 and 68: Connecting the ContentBridge System
- Page 69 and 70: Connecting the ContentDirectors Sys
- Page 71 and 72: Configuring a Stretch Cluster Syste
- Page 73 and 74: 10 GbE Module 1 GbE Module Public V
- Page 75 and 76: System Installation with ContentSer
- Page 77 and 78: CHAPTER 2 System Installation with
- Page 79 and 80: ContentBridge (optional) SystemMana
- Page 81 and 82: • The VLAN name and ID for the su
- Page 83 and 84: The following software installation
- Page 85 and 86: Before You Begin System Installatio
- Page 87 and 88: To rack mount an Omneon MediaGrid:
- Page 89 and 90: Figure 26. Rack Mounting the Conten
- Page 91 and 92: Installing the ContentServer Disk D
- Page 93 and 94: System Installation with ContentSer
- Page 95 and 96: 2 1 2 1 ID ID Figure 32. ContentSer
- Page 97 and 98: System Installation with ContentSer
- Page 99 and 100: System Installation with ContentSer
- Page 101 and 102: System Installation with ContentSer
- Page 103 and 104: 2. Continue connecting any remainin
- Page 105 and 106: System Installation with ContentSer
- Page 107 and 108: CHAPTER 3 System Configuration This
- Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
- Page 111 and 112: System Configuration 4. If you are
- Page 113 and 114: 6. Apply power to the ContentServer
Module A<br />
To Client Network<br />
10-GbE SFP+ SFP+ Ports Ports 10-GbE SFP+ Ports<br />
Figure 17. <strong>Omneon</strong> <strong>MediaGrid</strong> and 10 GbE Network Switch Connections<br />
0<br />
1<br />
System Installation with ContentServer 3000 Series<br />
Module C Module D<br />
1<br />
0<br />
FAULT<br />
REMOVE<br />
POWER<br />
4 5<br />
2 3<br />
<strong>Omneon</strong>, Now Part of <strong>Harmonic</strong> 41<br />
Gb 1 Gb 2<br />
1<br />
2<br />
First ContentDirector<br />
First ContentServer<br />
1<br />
0<br />
SystemManager<br />
ContentBridge 2010B/2010C (Optional)<br />
FAULT<br />
REMOVE<br />
POWER<br />
4 5<br />
Module B