About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
Hardware Reference Indicator, Button, or Connector Description 7. NIC 3 connector Use for Gigabit Ethernet connection to switch. 8. System status indicator Blinks when the front or back system identification button is pressed. 9. System identification button Both the SystemManager application and the identification buttons on the front and back panels can be used to locate a particular system within a rack. When one of these buttons is pressed, the LCD display on the front of the device and the blue system status indicator on the back blink until one of the buttons is pressed again. 10. Power supply 1 Dual redundant power supplies provide power to the system. 11. Power supply 2 Power Supply LED Figure 81 and Table 12 describe the typical Redundant Power Supply Indicator and its functions. Figure 81. ContentDirector Power Supply Indicator Table 12. Power Supply Indicator Pattern Indicator Pattern Condition Power supply status indicator Not lit AC power is not connected. Green In standby mode, indicates that a valid AC source is connected to the power supply, and that the power supply is operational. When the system is on, it also indicates that the power supply is providing DC power to the system. Amber Indicates a problem with the power supply. 206 Installation and Configuration Guide
Indicator Pattern Condition ContentDirector NIC Indicators Hardware Reference Alternating Green and Amber When hot-adding a power supply, this indicates that the power supply is mismatched with the other power supply (a high output power supply and a Energy Smart power supply are installed in the same system). To correct this, replace the power supply that has the flashing indicator with a power supply that matches the capacity of the other installed power supply. Each NIC on the rear panel has an indicator that provides information on network activity and link status. Figure 82, and Table 13 detail the NIC indicators and the possible states of each. indicator 2. Activity indicator Figure 82. ContentDirector NIC Indicators Note that the indicator codes for NIC 0 and NIC 1 differ from NIC 2 and NIC 3. Refer to Table 13. Table 13. NIC Indicator Codes NIC 0 and NIC 1 Indicators NIC 2 and NIC 3 Indicators Connection Status Link and activity indicators are off NIC is not connected. Link indicator is green Link indicator is amber NIC is connected to a valid link on the network. Link indicator is amber Link indicator is green or blinking green Activity indicator is amber blinking 1. Link ContentBridge 1000B Activity indicator is green blinking NIC is connected to a valid network link at 10/100 Mbps Data is being sent or received over the network. The ContentBridge 1000B, an optional Omneon MediaGrid system component, provides access to Omneon MediaGrid for those client platforms that do not have the FSD installed or do not use the Omneon MediaGrid API. Omneon, Now Part of Harmonic 207
- Page 179 and 180: 11. Click the Browse button and the
- Page 181 and 182: Figure 53. Connect to Omneon MediaG
- Page 183 and 184: Figure 54. Automatic MediaGrid Conn
- Page 185 and 186: Accessing the Omneon MediaGrid Moun
- Page 187 and 188: Table 4. Mount Options (Continued)
- Page 189 and 190: Table 5. Mount Options (Continued)
- Page 191 and 192: Accessing the Omneon MediaGrid To u
- Page 193 and 194: Figure 58. MyDir Properties Accessi
- Page 195 and 196: Accessing the Omneon MediaGrid •
- Page 197 and 198: Using AFP on a Macintosh Client Fol
- Page 199 and 200: Accessing the Omneon MediaGrid For
- Page 201 and 202: CHAPTER 6 Administrative Procedures
- Page 203 and 204: Table 6. mgcopy Values Values Descr
- Page 205 and 206: Figure 60. Firmware Version Selecti
- Page 207 and 208: Administrative Procedures Use the f
- Page 209 and 210: Administrative Procedures 1. From t
- Page 211 and 212: To log on to a ContentDirector: 1.
- Page 213 and 214: 3. Type the following two lines at
- Page 215 and 216: Administrative Procedures 1. Attach
- Page 217 and 218: 4. Change directory to /mnt, as sho
- Page 219 and 220: CHAPTER 7 Hardware Reference This c
- Page 221 and 222: Figure 67. Rear View of 1010 Networ
- Page 223 and 224: Power, fault and locator LEDs Conso
- Page 225 and 226: Power and fault LEDs Figure 75. Rea
- Page 227 and 228: Table 8. ContentDirector Indicator
- Page 229: Drive-status Indicator Pattern Cond
- Page 233 and 234: Off White Blue Red Ethernet Port 0
- Page 235 and 236: Link indicator Port 0 Port 1 Figure
- Page 237 and 238: Yellow Power on White Red Ethernet
- Page 239 and 240: Table 21. Drive-status Indicator Pa
- Page 241 and 242: Power Supply LEDs Figure 93 and Tab
- Page 243 and 244: Table 26. ContentServer 1042 Ethern
- Page 245 and 246: Table 29. ContentServer 1042B Rear
- Page 247 and 248: Figure 99. Rear View of ContentServ
- Page 249 and 250: 1 PWR RST MediaGrid Figure 101. Con
- Page 251 and 252: Table 34. ContentServer 2122 Front
- Page 253 and 254: 2 1 2 1 3 ID Figure 104. ContentSer
- Page 255 and 256: Front Panel Components Front Bezel
- Page 257 and 258: Table 39. ContentServer 2124 Front
- Page 259 and 260: 2 1 2 1 3 ID Figure 109. ContentSer
- Page 261 and 262: ContentServer 3000 Hardware Referen
- Page 263 and 264: Left Control Panel Figure 113. Cont
- Page 265 and 266: Table 46. Disk Drive Status LEDs LE
- Page 267 and 268: Table 47. ContentServer 3000 Rear P
- Page 269 and 270: Figure 117. NVRAM Card LEDs 2 1 3 T
- Page 271 and 272: Figure 119. 10 Gigabit Ethernet Add
- Page 273 and 274: 1 Drive 15 15 OPEN 14 Figure 121. C
- Page 275 and 276: Table 55. ContentStore 3160 Front B
- Page 277 and 278: Table 57. ContentStore 3160 Rear Pa
- Page 279 and 280: CHAPTER 8 Troubleshooting This sect
Indicator Pattern Condition<br />
ContentDirector NIC Indicators<br />
Hardware Reference<br />
Alternating Green and Amber When hot-adding a power supply, this indicates that the<br />
power supply is mismatched with the other power supply (a<br />
high output power supply and a Energy Smart power supply<br />
are installed in the same system). To correct this, replace the<br />
power supply that has the flashing indicator with a power<br />
supply that matches the capacity of the other installed power<br />
supply.<br />
Each NIC on the rear panel has an indicator that provides information on network activity and link<br />
status. Figure 82, and Table 13 detail the NIC indicators and the possible states of each.<br />
indicator<br />
2. Activity indicator<br />
Figure 82. ContentDirector NIC Indicators<br />
Note that the indicator codes for NIC 0 and NIC 1 differ from NIC 2 and NIC 3. Refer to Table 13.<br />
Table 13. NIC Indicator Codes<br />
NIC 0 and NIC 1 Indicators NIC 2 and NIC 3 Indicators Connection Status<br />
Link and activity indicators are off NIC is not connected.<br />
Link indicator is green Link indicator is amber NIC is connected to a valid link on<br />
the network.<br />
Link indicator is amber Link indicator is green or<br />
blinking green<br />
Activity indicator is amber<br />
blinking<br />
1. Link<br />
ContentBridge 1000B<br />
Activity indicator is green<br />
blinking<br />
NIC is connected to a valid network<br />
link at 10/100 Mbps<br />
Data is being sent or received over<br />
the network.<br />
The ContentBridge 1000B, an optional <strong>Omneon</strong> <strong>MediaGrid</strong> system component, provides access to<br />
<strong>Omneon</strong> <strong>MediaGrid</strong> for those client platforms that do not have the FSD installed or do not use the<br />
<strong>Omneon</strong> <strong>MediaGrid</strong> API.<br />
<strong>Omneon</strong>, Now Part of <strong>Harmonic</strong> 207
Change language