About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
Administrative Procedures 1. Insert the “Omneon MediaGrid Platform Support Package” CD-ROM into the DVD drive. 2. Using an attached keyboard and monitor, log on to the ContentDirector as “ovnuser” using the password “OVN@SvCaUsa”. An example is shown below. Fedora Core release 4 (Stentz) Kernel 2.6.12 on an x86_64 login: ovnuser Password: [ovnuser@cld ~]$ 3. On the Linux command line, mount the CD-ROM onto the /mnt directory by typing the following: [ovnuser@cld ~]$ sudo mount /dev/cdrom /mnt/ Ignore the “mounting read-only” warning message if it displays. 4. Change to the directory /mnt, as shown below: [ovnuser@cld ~]$ cd /mnt 5. Execute the installation script by typing the following: [ovnuser@cld mnt]$ sudo ./install_hw.sh A series of output lines display, showing the progress of the installation sequence. 6. Once the command prompt returns, eject the CD by typing the following commands: [ovnuser@cld ~]$ cd / [ovnuser@cld ~]$ sudo eject Continue with the remaining ContentDirector software installation procedures. Installing the ContentDirector Software ContentDirector software is pre-installed prior to shipping, though may require upgrading to the latest version. Refer to “Software Installation and Upgrades” in the Omneon SystemManager User Guide to upgrade ContentDirectors with the latest version of software. To install the ContentDirector software for the first time: 1. Insert the “Omneon MediaGrid Software Installation” CD-ROM into the DVD drive. 2. Using the attached keyboard and monitor, log on to the ContentDirector as “ovnuser” using the password “OVN@SvCaUsa”. An example is shown below. Fedora Core release 4 (Stentz) Kernel 2.6.12 on an x86_64 login: ovnuser Password: [ovnuser@cld ~]$ 3. On the Linux command line, mount the CD-ROM onto the /mnt directory by typing the following: [ovnuser@cld ~]$ sudo mount /dev/cdrom /mnt/ Ignore the “mounting read-only” warning message if it displays. 192 Installation and Configuration Guide
4. Change directory to /mnt, as shown below: [ovnuser@cld ~]$ cd /mnt 5. Execute the installation script by typing the following: [ovnuser@cld mnt]$ sudo ./install.sh A series of output lines display, showing the progress of the installation sequence. 6. Press ENTER. Administrative Procedures 7. Once the command prompt returns, reboot the ContentDirector by typing the following: [ovnuser@cld mnt]$ sudo reboot The ContentDirector reboots in approximately 5 minutes. Omneon, Now Part of Harmonic 193
- Page 165 and 166: CHAPTER 4 Installing the File Syste
- Page 167 and 168: Installing the File System Driver s
- Page 169 and 170: Installing the File System Driver 3
- Page 171 and 172: CHAPTER 5 Accessing the Omneon Medi
- Page 173 and 174: Figure 45. Omneon MediaGrid Login A
- Page 175 and 176: Accessing the Omneon MediaGrid •
- Page 177 and 178: Automatically Mounting a File Syste
- Page 179 and 180: 11. Click the Browse button and the
- Page 181 and 182: Figure 53. Connect to Omneon MediaG
- Page 183 and 184: Figure 54. Automatic MediaGrid Conn
- Page 185 and 186: Accessing the Omneon MediaGrid Moun
- Page 187 and 188: Table 4. Mount Options (Continued)
- Page 189 and 190: Table 5. Mount Options (Continued)
- Page 191 and 192: Accessing the Omneon MediaGrid To u
- Page 193 and 194: Figure 58. MyDir Properties Accessi
- Page 195 and 196: Accessing the Omneon MediaGrid •
- Page 197 and 198: Using AFP on a Macintosh Client Fol
- Page 199 and 200: Accessing the Omneon MediaGrid For
- Page 201 and 202: CHAPTER 6 Administrative Procedures
- Page 203 and 204: Table 6. mgcopy Values Values Descr
- Page 205 and 206: Figure 60. Firmware Version Selecti
- Page 207 and 208: Administrative Procedures Use the f
- Page 209 and 210: Administrative Procedures 1. From t
- Page 211 and 212: To log on to a ContentDirector: 1.
- Page 213 and 214: 3. Type the following two lines at
- Page 215: Administrative Procedures 1. Attach
- Page 219 and 220: CHAPTER 7 Hardware Reference This c
- Page 221 and 222: Figure 67. Rear View of 1010 Networ
- Page 223 and 224: Power, fault and locator LEDs Conso
- Page 225 and 226: Power and fault LEDs Figure 75. Rea
- Page 227 and 228: Table 8. ContentDirector Indicator
- Page 229 and 230: Drive-status Indicator Pattern Cond
- Page 231 and 232: Indicator Pattern Condition Content
- Page 233 and 234: Off White Blue Red Ethernet Port 0
- Page 235 and 236: Link indicator Port 0 Port 1 Figure
- Page 237 and 238: Yellow Power on White Red Ethernet
- Page 239 and 240: Table 21. Drive-status Indicator Pa
- Page 241 and 242: Power Supply LEDs Figure 93 and Tab
- Page 243 and 244: Table 26. ContentServer 1042 Ethern
- Page 245 and 246: Table 29. ContentServer 1042B Rear
- Page 247 and 248: Figure 99. Rear View of ContentServ
- Page 249 and 250: 1 PWR RST MediaGrid Figure 101. Con
- Page 251 and 252: Table 34. ContentServer 2122 Front
- Page 253 and 254: 2 1 2 1 3 ID Figure 104. ContentSer
- Page 255 and 256: Front Panel Components Front Bezel
- Page 257 and 258: Table 39. ContentServer 2124 Front
- Page 259 and 260: 2 1 2 1 3 ID Figure 109. ContentSer
- Page 261 and 262: ContentServer 3000 Hardware Referen
- Page 263 and 264: Left Control Panel Figure 113. Cont
- Page 265 and 266: Table 46. Disk Drive Status LEDs LE
Administrative Procedures<br />
1. Insert the “<strong>Omneon</strong> <strong>MediaGrid</strong> Platform Support Package” CD-ROM into the DVD drive.<br />
2. Using an attached keyboard and monitor, log on to the ContentDirector as “ovnuser” using the<br />
password “OVN@SvCaUsa”. An example is shown below.<br />
Fedora Core release 4 (Stentz)<br />
Kernel 2.6.12 on an x86_64<br />
login: ovnuser<br />
Password:<br />
[ovnuser@cld ~]$<br />
3. On the Linux command line, mount the CD-ROM onto the /mnt directory by typing the following:<br />
[ovnuser@cld ~]$ sudo mount /dev/cdrom /mnt/<br />
Ignore the “mounting read-only” warning message if it displays.<br />
4. Change to the directory /mnt, as shown below:<br />
[ovnuser@cld ~]$ cd /mnt<br />
5. Execute the installation script by typing the following:<br />
[ovnuser@cld mnt]$ sudo ./install_hw.sh<br />
A series of output lines display, showing the progress of the installation sequence.<br />
6. Once the command prompt returns, eject the CD by typing the following commands:<br />
[ovnuser@cld ~]$ cd /<br />
[ovnuser@cld ~]$ sudo eject<br />
Continue with the remaining ContentDirector software installation procedures.<br />
Installing the ContentDirector Software<br />
ContentDirector software is pre-installed prior to shipping, though may require upgrading to the latest<br />
version. Refer to “Software Installation and Upgrades” in the <strong>Omneon</strong> SystemManager User Guide to<br />
upgrade ContentDirectors with the latest version of software.<br />
To install the ContentDirector software for the first time:<br />
1. Insert the “<strong>Omneon</strong> <strong>MediaGrid</strong> Software Installation” CD-ROM into the DVD drive.<br />
2. Using the attached keyboard and monitor, log on to the ContentDirector as “ovnuser” using the<br />
password “OVN@SvCaUsa”. An example is shown below.<br />
Fedora Core release 4 (Stentz)<br />
Kernel 2.6.12 on an x86_64<br />
login: ovnuser<br />
Password:<br />
[ovnuser@cld ~]$<br />
3. On the Linux command line, mount the CD-ROM onto the /mnt directory by typing the following:<br />
[ovnuser@cld ~]$ sudo mount /dev/cdrom /mnt/<br />
Ignore the “mounting read-only” warning message if it displays.<br />
192 Installation and Configuration Guide