About Omneon MediaGrid - Harmonic Inc

More documents

Recommendations

Info

Administrative Procedures 1. From the Configuration tab, click the Servers & Switches icon in the left-hand column to open the Servers & Switches page. 2. In the ContentServers/ContentStores section, click the name of the ContentServer you wish to power down. The ContentStore Properties page appears. 3. Click the Shutdown button located in the top section of the page. 4. When the confirmation message appears, click OK. 5. Check the Status field to verify that it indicates Not Responding. Note that it may take a few minutes for the status to change, depending on the length of the discovery cycle and the status of other devices in your network. 6. Press the Power button on the control panel on the front of the server to power down. Powering On an Omneon MediaGrid System Use the following steps to power on the devices in an Omneon MediaGrid system. IMPORTANT: The procedures must be followed in the order described below. 1. Apply power to the ContentDirectors by connecting both power cords to separate, isolated power sources. 2. Press the Power button on the front of each ContentDirector. The ContentDirectors take approximately five minutes to start. Wait for the power-on indicator to light before continuing. 3. Apply power to the ContentServers by connecting the power cords to power sources. 4. Turn on the ContentServers as follows: • For ContentServers 1000 Series and 2000 Series, press the Power switch on the back of the server. • For ContentServers 3000 Series, press the Power button on the control panel on the front of the server. 5. Apply power to the ContentStores by connecting the power cords to power sources. 6. Turn on the ContentStores by pressing the Power button on the control panel on the front of each ContentStore. 7. Apply power to the SystemManager by connecting the power cord to a power source. Press the Power button on the front of the SystemManager. 8. Apply power to the ContentBridge (if part of the system) by pressing the Power switch on the back of the device. Make sure all of the ContentServers are running before powering on the ContentBridge. NOTE: If you are using a High Bandwidth ContentBridge, the power switch may be located on the front of the device. Logging on to a ContentDirector Making changes to certain configuration files and completing the Configuration Assistant requires logging on to a ContentDirector. 186 Installation and Configuration Guide
To log on to a ContentDirector: 1. Use the following case-sensitive user name and password: • User name: ovnuser • Password: OVN@SvCaUsa Administrative Procedures 2. Once you have logged on to a ContentDirector, each command that changes or saves files must be preceded by the “sudo” command. NOTE: Entries requiring this command are identified in this guide. Once the password is entered, you may complete “sudo” commands without a password for five minutes. Managing Network Switches This section provides information about managing the network switches. Changing the Default Network Switch User Name and Password Each network switch is preset with the following user name and password: • User name: Administrator • Password: omneon To change the default user name and password. 1. Connect to the switch using HyperTerminal. 2. Type the following at the command prompt to edit the configuration file and then press ENTER: HP ProCurve Switch 6400cl-6XG# config 3. Type the following to set the user name and then press Enter. Enter the user name you want to use, including the quotation marks: HP ProCurve Switch 6400cl-6XG(config)# password manager user-name “user name” 4. Type a password of up to 16 characters and then press Enter. New password for Manager: your password 5. Retype the password to confirm. 6. Type the following to save the configuration file: HP ProCurve Switch 6400cl-6XG(config)# write memory 7. Type the following and then press ENTER to exit HyperTerminal: HP ProCurve Switch 6400cl-6XG(config)# logout NOTE: If you happen to forget the user name and password, press the Clear button on the front of the switch to clear the current user name and password. Repeat the steps above to create a new user name and password. Omneon, Now Part of Harmonic 187
Page 1 and 2:
Omneon MediaGrid Installation and C
Page 3 and 4:
FCC Compliance This equipment has b
Page 5 and 6:
Parameter Specification Detail Safe
Page 7 and 8:
Parameter Specification Detail EMC
Page 9 and 10:
Network Switch 2924, 2948 and 5406
Page 11 and 12:
CAUTION: Danger of explosion if bat
Page 13 and 14:
• Storage Temperature -104 °F to
Page 15 and 16:
Contents Introduction . . . . . . .
Page 17 and 18:
Contents Private VLANs . . . . . .
Page 19 and 20:
Contents Joining a ContentBridge 10
Page 21 and 22:
Contents About Access Control Lists
Page 23 and 24:
Contents Front Panel View . . . . .
Page 25 and 26:
Omneon MediaGrid Version 3.1.1 Intr
Page 27 and 28:
• Cluster, in the context of an O
Page 29 and 30:
Two models of ContentDirectors are
Page 31 and 32:
Keep in mind the following addition
Page 33 and 34:
1. From Windows, click the Start bu
Page 35 and 36:
1. Add two registry parameters to t
Page 37 and 38:
CHAPTER 1 System Installation with
Page 39 and 40:
ContentBridge (optional) SystemMana
Page 41 and 42:
• Cluster names and device names
Page 43 and 44:
Public VLAN Private VLAN 1 Private
Page 45 and 46:
Public VLAN Private VLAN 1 Private
Page 47 and 48:
16 5x(2+1)+1 500 GB 5 TB 16 5x(2+1)
Page 49 and 50:
System Installation with ContentSer
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Figure 10. ContentServer 3000 and 1
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
10GbE Switch First Switch Second Sw
Page 65 and 66:
Module A To Client Network 10-GbE S
Page 67 and 68:
Connecting the ContentBridge System
Page 69 and 70:
Connecting the ContentDirectors Sys
Page 71 and 72:
Configuring a Stretch Cluster Syste
Page 73 and 74:
10 GbE Module 1 GbE Module Public V
Page 75 and 76:
Page 77 and 78:
CHAPTER 2 System Installation with
Page 79 and 80:
ContentBridge (optional) SystemMana
Page 81 and 82:
• The VLAN name and ID for the su
Page 83 and 84:
The following software installation
Page 85 and 86:
Before You Begin System Installatio
Page 87 and 88:
To rack mount an Omneon MediaGrid:
Page 89 and 90:
Figure 26. Rack Mounting the Conten
Page 91 and 92:
Installing the ContentServer Disk D
Page 93 and 94:
Page 95 and 96:
2 1 2 1 ID ID Figure 32. ContentSer
Page 97 and 98:
Page 99 and 100:
Page 101 and 102:
Page 103 and 104:
2. Continue connecting any remainin
Page 105 and 106:
Page 107 and 108:
CHAPTER 3 System Configuration This
Page 109 and 110:
Password: OVN@SvCaUsa 3. Enter the
Page 111 and 112:
System Configuration 4. If you are
Page 113 and 114:
6. Apply power to the ContentServer
Page 115 and 116:
Notes on Active Directory Configura
Page 117 and 118:
Follow the prompts to initialize th
Page 119 and 120:
Joining an Omneon MediaGrid Cluster
Page 121 and 122:
1. From your SSH terminal, edit /et
Page 123 and 124:
A list of users in the domain displ
Page 125 and 126:
System Configuration 1. After confi
Page 127 and 128:
4. Type the following commands to r
Page 129 and 130:
The expected result is: Domain=[SNV
Page 131 and 132:
System Configuration This mount poi
Page 133 and 134:
System Configuration c. Replace wi
Page 135 and 136:
Modify the file as follows: System
Page 137 and 138:
Omneon MediaGrid name ContentDirect
Page 139 and 140:
Editing the LDAP Configuration File
Page 141 and 142:
System Configuration 4. Create a Sa
Page 143 and 144:
Modify the file as follows: System
Page 145 and 146:
Figure 43. Server Admin Open Direct
Page 147 and 148:
The following is a sample output fr
Page 149 and 150:
System Configuration a. Replace dom
Page 151 and 152:
System Configuration NOTE: Upon joi
Page 153 and 154:
To verify the service: 1. Type the
Page 155 and 156:
System Configuration configurations
Page 157 and 158:
To configure the amount of memory u
Page 159 and 160: System Configuration 4. Set the val
Page 161 and 162: System Configuration 9. As the tran
Page 163 and 164: The acceptable options are “YES
Page 165 and 166: CHAPTER 4 Installing the File Syste
Page 167 and 168: Installing the File System Driver s
Page 169 and 170: Installing the File System Driver 3
Page 171 and 172: CHAPTER 5 Accessing the Omneon Medi
Page 173 and 174: Figure 45. Omneon MediaGrid Login A
Page 175 and 176: Accessing the Omneon MediaGrid •
Page 177 and 178: Automatically Mounting a File Syste
Page 179 and 180: 11. Click the Browse button and the
Page 181 and 182: Figure 53. Connect to Omneon MediaG
Page 183 and 184: Figure 54. Automatic MediaGrid Conn
Page 185 and 186: Accessing the Omneon MediaGrid Moun
Page 187 and 188: Table 4. Mount Options (Continued)
Page 189 and 190: Table 5. Mount Options (Continued)
Page 191 and 192: Accessing the Omneon MediaGrid To u
Page 193 and 194: Figure 58. MyDir Properties Accessi
Page 195 and 196: Accessing the Omneon MediaGrid •
Page 197 and 198: Using AFP on a Macintosh Client Fol
Page 199 and 200: Accessing the Omneon MediaGrid For
Page 201 and 202: CHAPTER 6 Administrative Procedures
Page 203 and 204: Table 6. mgcopy Values Values Descr
Page 205 and 206: Figure 60. Firmware Version Selecti
Page 207 and 208: Administrative Procedures Use the f
Page 209: Administrative Procedures 1. From t
Page 213 and 214: 3. Type the following two lines at
Page 215 and 216: Administrative Procedures 1. Attach
Page 217 and 218: 4. Change directory to /mnt, as sho
Page 219 and 220: CHAPTER 7 Hardware Reference This c
Page 221 and 222: Figure 67. Rear View of 1010 Networ
Page 223 and 224: Power, fault and locator LEDs Conso
Page 225 and 226: Power and fault LEDs Figure 75. Rea
Page 227 and 228: Table 8. ContentDirector Indicator
Page 229 and 230: Drive-status Indicator Pattern Cond
Page 231 and 232: Indicator Pattern Condition Content
Page 233 and 234: Off White Blue Red Ethernet Port 0
Page 235 and 236: Link indicator Port 0 Port 1 Figure
Page 237 and 238: Yellow Power on White Red Ethernet
Page 239 and 240: Table 21. Drive-status Indicator Pa
Page 241 and 242: Power Supply LEDs Figure 93 and Tab
Page 243 and 244: Table 26. ContentServer 1042 Ethern
Page 245 and 246: Table 29. ContentServer 1042B Rear
Page 247 and 248: Figure 99. Rear View of ContentServ
Page 249 and 250: 1 PWR RST MediaGrid Figure 101. Con
Page 251 and 252: Table 34. ContentServer 2122 Front
Page 253 and 254: 2 1 2 1 3 ID Figure 104. ContentSer
Page 255 and 256: Front Panel Components Front Bezel
Page 257 and 258: Table 39. ContentServer 2124 Front
Page 259 and 260: 2 1 2 1 3 ID Figure 109. ContentSer
Page 261 and 262:
ContentServer 3000 Hardware Referen
Page 263 and 264:
Left Control Panel Figure 113. Cont
Page 265 and 266:
Table 46. Disk Drive Status LEDs LE
Page 267 and 268:
Table 47. ContentServer 3000 Rear P
Page 269 and 270:
Figure 117. NVRAM Card LEDs 2 1 3 T
Page 271 and 272:
Figure 119. 10 Gigabit Ethernet Add
Page 273 and 274:
1 Drive 15 15 OPEN 14 Figure 121. C
Page 275 and 276:
Table 55. ContentStore 3160 Front B
Page 277 and 278:
Table 57. ContentStore 3160 Rear Pa
Page 279 and 280:
CHAPTER 8 Troubleshooting This sect
Page 281 and 282:
Troubleshooting The dhcp-leases fil
Page 283 and 284:
Troubleshooting The two most import
Page 285 and 286:
Troubleshooting points. The number
Page 287 and 288:
Security with Microsoft Domain Cont
Page 289 and 290:
mdsclientn dialog output: Troublesh
Page 291 and 292:
sessions output: *** 1/64 RPC sessi
Page 293 and 294:
APPENDIX A Legacy Hardware Platform
Page 295 and 296:
Figure 127. ContentDirector Hard Dr
Page 297 and 298:
. Figure 129. ContentDirector Power
Page 299 and 300:
Table 65. ContentDirector Indicator
Page 301 and 302:
Drive-status Indicator Pattern Cond
Page 303 and 304:
1. Link indicator 2. Activity indic
Page 305 and 306:
Figure 139 and Table 72 describe th
Page 307 and 308:
Figure 141. ContentBridge Front Pan
Page 309 and 310:
Table 77. ContentBridge 2010A Ether
Page 311 and 312:
Figure 145. ContentServer 1242 with
Page 313 and 314:
Table 81. ContentServer 1242 Ethern
show all

About Omneon MediaGrid - Harmonic Inc

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?