About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
Accessing the Omneon MediaGrid 176 Installation and Configuration Guide
CHAPTER 6 Administrative Procedures This section includes Omneon MediaGrid power off procedures, setting switch and ContentDirector passwords, and software upgrade procedures. The following topics are included: • Balancing the ContentServer 3000 Controllers • Using mgcopy to Copy Files Between MediaGrid Systems • Upgrading Omneon MediaGrid Firmware • Powering Down an Omneon MediaGrid System • Powering On an Omneon MediaGrid System • Logging on to a ContentDirector • Managing Network Switches • Installing Omneon MediaGrid and ContentDirector Software Balancing the ContentServer 3000 Controllers Any time one controller on a ContentServer goes down, which may be during an upgrade or replacement, the active Slice Server processes on that controller, which manage ContentServers and ContentStores, fail over to the remaining controller. Once both controllers are up and running, Omneon recommends that you balance the Slice Server processes across controllers to improve performance. This is done by using the Failback button on the ContentServer or ContentStore Properties page. Omneon recommends that you balance your ContentServer 3000 at these times: • Following a ContentServer upgrade. • Following a controller replacement. • Following a controller failover. • If the Managed ContentStores and ContentServers field on the ContentServer Properties page shows all, or a large majority, of ContentStores and ContentServers being managed by one controller (for example, five out of six). If you fail to balance your ContentServer in the situations listed above, it may affect the performance of the ContentServer. NOTE: Omneon recommends that you schedule balancing during times when the system is not loaded. For example, this may be late at night. System performance may be affected while balancing is occurring. Omneon MediaGrid Version 3.1.1 177
- Page 149 and 150: System Configuration a. Replace dom
- Page 151 and 152: System Configuration NOTE: Upon joi
- Page 153 and 154: To verify the service: 1. Type the
- Page 155 and 156: System Configuration configurations
- Page 157 and 158: To configure the amount of memory u
- Page 159 and 160: System Configuration 4. Set the val
- Page 161 and 162: System Configuration 9. As the tran
- Page 163 and 164: The acceptable options are “YES
- Page 165 and 166: CHAPTER 4 Installing the File Syste
- Page 167 and 168: Installing the File System Driver s
- Page 169 and 170: Installing the File System Driver 3
- Page 171 and 172: CHAPTER 5 Accessing the Omneon Medi
- Page 173 and 174: Figure 45. Omneon MediaGrid Login A
- Page 175 and 176: Accessing the Omneon MediaGrid •
- Page 177 and 178: Automatically Mounting a File Syste
- Page 179 and 180: 11. Click the Browse button and the
- Page 181 and 182: Figure 53. Connect to Omneon MediaG
- Page 183 and 184: Figure 54. Automatic MediaGrid Conn
- Page 185 and 186: Accessing the Omneon MediaGrid Moun
- Page 187 and 188: Table 4. Mount Options (Continued)
- Page 189 and 190: Table 5. Mount Options (Continued)
- Page 191 and 192: Accessing the Omneon MediaGrid To u
- Page 193 and 194: Figure 58. MyDir Properties Accessi
- Page 195 and 196: Accessing the Omneon MediaGrid •
- Page 197 and 198: Using AFP on a Macintosh Client Fol
- Page 199: Accessing the Omneon MediaGrid For
- Page 203 and 204: Table 6. mgcopy Values Values Descr
- Page 205 and 206: Figure 60. Firmware Version Selecti
- Page 207 and 208: Administrative Procedures Use the f
- Page 209 and 210: Administrative Procedures 1. From t
- Page 211 and 212: To log on to a ContentDirector: 1.
- Page 213 and 214: 3. Type the following two lines at
- Page 215 and 216: Administrative Procedures 1. Attach
- Page 217 and 218: 4. Change directory to /mnt, as sho
- Page 219 and 220: CHAPTER 7 Hardware Reference This c
- Page 221 and 222: Figure 67. Rear View of 1010 Networ
- Page 223 and 224: Power, fault and locator LEDs Conso
- Page 225 and 226: Power and fault LEDs Figure 75. Rea
- Page 227 and 228: Table 8. ContentDirector Indicator
- Page 229 and 230: Drive-status Indicator Pattern Cond
- Page 231 and 232: Indicator Pattern Condition Content
- Page 233 and 234: Off White Blue Red Ethernet Port 0
- Page 235 and 236: Link indicator Port 0 Port 1 Figure
- Page 237 and 238: Yellow Power on White Red Ethernet
- Page 239 and 240: Table 21. Drive-status Indicator Pa
- Page 241 and 242: Power Supply LEDs Figure 93 and Tab
- Page 243 and 244: Table 26. ContentServer 1042 Ethern
- Page 245 and 246: Table 29. ContentServer 1042B Rear
- Page 247 and 248: Figure 99. Rear View of ContentServ
- Page 249 and 250: 1 PWR RST MediaGrid Figure 101. Con
CHAPTER 6<br />
Administrative Procedures<br />
This section includes <strong>Omneon</strong> <strong>MediaGrid</strong> power off procedures, setting switch and ContentDirector<br />
passwords, and software upgrade procedures. The following topics are included:<br />
• Balancing the ContentServer 3000 Controllers<br />
• Using mgcopy to Copy Files Between <strong>MediaGrid</strong> Systems<br />
• Upgrading <strong>Omneon</strong> <strong>MediaGrid</strong> Firmware<br />
• Powering Down an <strong>Omneon</strong> <strong>MediaGrid</strong> System<br />
• Powering On an <strong>Omneon</strong> <strong>MediaGrid</strong> System<br />
• Logging on to a ContentDirector<br />
• Managing Network Switches<br />
• Installing <strong>Omneon</strong> <strong>MediaGrid</strong> and ContentDirector Software<br />
Balancing the ContentServer 3000 Controllers<br />
Any time one controller on a ContentServer goes down, which may be during an upgrade or<br />
replacement, the active Slice Server processes on that controller, which manage ContentServers and<br />
ContentStores, fail over to the remaining controller. Once both controllers are up and running,<br />
<strong>Omneon</strong> recommends that you balance the Slice Server processes across controllers to improve<br />
performance. This is done by using the Failback button on the ContentServer or ContentStore<br />
Properties page.<br />
<strong>Omneon</strong> recommends that you balance your ContentServer 3000 at these times:<br />
• Following a ContentServer upgrade.<br />
• Following a controller replacement.<br />
• Following a controller failover.<br />
• If the Managed ContentStores and ContentServers field on the ContentServer Properties<br />
page shows all, or a large majority, of ContentStores and ContentServers being managed by one<br />
controller (for example, five out of six).<br />
If you fail to balance your ContentServer in the situations listed above, it may affect the performance<br />
of the ContentServer.<br />
NOTE: <strong>Omneon</strong> recommends that you schedule balancing during times when the system is not loaded. For<br />
example, this may be late at night. System performance may be affected while balancing is occurring.<br />
<strong>Omneon</strong> <strong>MediaGrid</strong> Version 3.1.1 177