About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
System Configuration NOTE: When the ContentBridge 2010B/2010C is configured for Active Directory, “CB” mount points that provide access for individual users are NOT supported and will need to be removed from the ContentBridge configuration file. Make sure to perform step 8 in the following procedure to remove those “CB” entries. Before you begin: • Make sure you have reviewed the Omneon MediaGrid Installation Planning Guide and have a completed copy of the configuration worksheet included in that document on hand. • Make sure you have a USB drive on hand. • Make sure you have the following Active Directory information: • The Active Directory “realm” for this Omneon MediaGrid system • The Active Directory “workgroup” for this Omneon MediaGrid • The “hostname” for the Active Directory server • The Active Directory Server's FQDN (Fully Qualified Domain Name) • The IP address for the Active Directory server • The user name and password for a valid user account with administrative privileges CAUTION: Entering incorrect information in the Configuration Assistant could result in a loss of connection to the ContentBridge 2010B/2010C. For assistance, contact Omneon Technical Support. To add a ContentBridge 2010B/2010C to an Active Directory Domain: 1. Connect a monitor and keyboard to the ContentBridge 2010B/2010C you wish to add to the Active Directory domain. 2. Log on to the ContentBridge using the following user name and password: User name: ovnuser Password: OVN@SvCaUsa 3. Type the following command to set the FIRSTBOOT mode on the ContentBridge: sudo initconfig --setflag NOTE: In some cases, running this command can result in the following message: [root@hbcb1-1 ~]# initconfig --setflag Setting Firstboot flags (local) sh: /tftpboot/config/FIRSTBOOT: No such file or directory This message can be ignored. If you wish to verify that FIRSTBOOT mode was set, you can check that the following files are now available on the ContentBridge: /tmp/FIRSTBOOT /omneon/sharedsys/FIRSTBOOT 102 Installation and Configuration Guide
4. Type the following commands to run the configuration assistant: cd /home/ovnuser/scripts sudo ./autoconfig -m System Configuration The configuration script asks a series of questions requiring information specific to the customer site. Use the information from the Omneon MediaGrid Installation Planning Guide to complete the answers. Note that the assistant will display suggested responses in brackets. During the assistant, you can use the up or down arrow keys to tab to previous responses. 5. When prompted by the configuration assistant, insert a USB drive. The configuration assistant automatically copies the configuration information to the USB drive. 6. Type the following command to copy the configuration information to this ContentBridge 2010B/2010C: sudo ./copyconfigs -m 7. When prompted to enter the ID of the ContentBridge in the specified range, select 0 as the ID. 8. Once copying is complete, remove the USB drive from the ContentBridge. 9. Type the following command to remove the ContentBridge from the FIRSTBOOT mode: sudo initconfig --rmflag 10. Type the following commands to join this ContentBridge 2010B/2010C to the Active Directory domain and restart services: sudo service gateway stop sudo net ads join -U % -S sudo service gateway start 11. If you wish to add additional ContentBridges 2010B/2010C to the Active Directory domain at this point, repeat the following steps on each additional ContentBridge 2010B/2010C: NOTE: The total number of ContentBridges 2010B/2010C selected for configuration must match the total number of ContentBridges selected when running the Configuration Assistant in step 4 above. a. Insert the USB drive that contains the configuration information. b. Log on to the ContentBridge using the credentials used in step 2 above. c. Type: sudo initconfig --setflag d. Type: sudo ./copyconfigs -m e. Select the ID(s), starting from 1, in increasing order for each additional ContentBridge 2010B/2010C. f. Type: sudo initconfig --rmflag g. Perform the commands in step 10 above to join the ContentBridge to the Active Directory domain and restart services. 12. As a final step, for each ContentBridge, you must remove any “CB” entries that provide access to individual users from the /etc/gateway.conf and etc/password files. Omneon, Now Part of Harmonic 103
- Page 75 and 76: System Installation with ContentSer
- Page 77 and 78: CHAPTER 2 System Installation with
- Page 79 and 80: ContentBridge (optional) SystemMana
- Page 81 and 82: • The VLAN name and ID for the su
- Page 83 and 84: The following software installation
- Page 85 and 86: Before You Begin System Installatio
- Page 87 and 88: To rack mount an Omneon MediaGrid:
- Page 89 and 90: Figure 26. Rack Mounting the Conten
- Page 91 and 92: Installing the ContentServer Disk D
- Page 93 and 94: System Installation with ContentSer
- Page 95 and 96: 2 1 2 1 ID ID Figure 32. ContentSer
- Page 97 and 98: System Installation with ContentSer
- Page 99 and 100: System Installation with ContentSer
- Page 101 and 102: System Installation with ContentSer
- Page 103 and 104: 2. Continue connecting any remainin
- Page 105 and 106: System Installation with ContentSer
- Page 107 and 108: CHAPTER 3 System Configuration This
- Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
- Page 111 and 112: System Configuration 4. If you are
- Page 113 and 114: 6. Apply power to the ContentServer
- Page 115 and 116: Notes on Active Directory Configura
- Page 117 and 118: Follow the prompts to initialize th
- Page 119 and 120: Joining an Omneon MediaGrid Cluster
- Page 121 and 122: 1. From your SSH terminal, edit /et
- Page 123 and 124: A list of users in the domain displ
- Page 125: System Configuration 1. After confi
- Page 129 and 130: The expected result is: Domain=[SNV
- Page 131 and 132: System Configuration This mount poi
- Page 133 and 134: System Configuration c. Replace wi
- Page 135 and 136: Modify the file as follows: System
- Page 137 and 138: Omneon MediaGrid name ContentDirect
- Page 139 and 140: Editing the LDAP Configuration File
- Page 141 and 142: System Configuration 4. Create a Sa
- Page 143 and 144: Modify the file as follows: System
- Page 145 and 146: Figure 43. Server Admin Open Direct
- Page 147 and 148: The following is a sample output fr
- Page 149 and 150: System Configuration a. Replace dom
- Page 151 and 152: System Configuration NOTE: Upon joi
- Page 153 and 154: To verify the service: 1. Type the
- Page 155 and 156: System Configuration configurations
- Page 157 and 158: To configure the amount of memory u
- Page 159 and 160: System Configuration 4. Set the val
- Page 161 and 162: System Configuration 9. As the tran
- Page 163 and 164: The acceptable options are “YES
- Page 165 and 166: CHAPTER 4 Installing the File Syste
- Page 167 and 168: Installing the File System Driver s
- Page 169 and 170: Installing the File System Driver 3
- Page 171 and 172: CHAPTER 5 Accessing the Omneon Medi
- Page 173 and 174: Figure 45. Omneon MediaGrid Login A
- Page 175 and 176: Accessing the Omneon MediaGrid •
System Configuration<br />
NOTE: When the ContentBridge 2010B/2010C is configured for Active Directory, “CB” mount points that<br />
provide access for individual users are NOT supported and will need to be removed from the ContentBridge<br />
configuration file. Make sure to perform step 8 in the following procedure to remove those “CB” entries.<br />
Before you begin:<br />
• Make sure you have reviewed the <strong>Omneon</strong> <strong>MediaGrid</strong> Installation Planning Guide and have a<br />
completed copy of the configuration worksheet included in that document on hand.<br />
• Make sure you have a USB drive on hand.<br />
• Make sure you have the following Active Directory information:<br />
• The Active Directory “realm” for this <strong>Omneon</strong> <strong>MediaGrid</strong> system<br />
• The Active Directory “workgroup” for this <strong>Omneon</strong> <strong>MediaGrid</strong><br />
• The “hostname” for the Active Directory server<br />
• The Active Directory Server's FQDN (Fully Qualified Domain Name)<br />
• The IP address for the Active Directory server<br />
• The user name and password for a valid user account with administrative privileges<br />
CAUTION: Entering incorrect information in the Configuration Assistant could result in a<br />
loss of connection to the ContentBridge 2010B/2010C. For assistance, contact <strong>Omneon</strong><br />
Technical Support.<br />
To add a ContentBridge 2010B/2010C to an Active Directory Domain:<br />
1. Connect a monitor and keyboard to the ContentBridge 2010B/2010C you wish to add to the Active<br />
Directory domain.<br />
2. Log on to the ContentBridge using the following user name and password:<br />
User name: ovnuser<br />
Password: OVN@SvCaUsa<br />
3. Type the following command to set the FIRSTBOOT mode on the ContentBridge:<br />
sudo initconfig --setflag<br />
NOTE: In some cases, running this command can result in the following message:<br />
[root@hbcb1-1 ~]# initconfig --setflag<br />
Setting Firstboot flags (local)<br />
sh: /tftpboot/config/FIRSTBOOT: No such file or directory<br />
This message can be ignored. If you wish to verify that FIRSTBOOT mode was set, you can check that<br />
the following files are now available on the ContentBridge:<br />
/tmp/FIRSTBOOT<br />
/omneon/sharedsys/FIRSTBOOT<br />
102 Installation and Configuration Guide