About Omneon MediaGrid - Harmonic Inc

More documents

Recommendations

Info

System Configuration The processes have started if you see the following: mdsstartup (pid 22950) is running... oujfh is stopped ousd is stopped ssmd is stopped mdscore is stopped trapmond (pid 22947) is running... 4. Note that “pid” is a process ID number, which will vary. A few seconds after cluster initialization, the other processes (oujf, ouse, ssmd, mdscore) will start. 5. If the message displayed in the prior step is “mdsstartup is stopped”, type the command below to start the ContentDirector service: sudo service omcld start If you did not initialize clusters as part of the configuration assistant, continue to the following section. If you already initialized clusters as part of the configuration assistant, continue to Setting the Omneon MediaGrid System Time. Initializing Clusters NOTE: If you already initialized clusters as part of the configuration assistant, continue to Setting the Omneon MediaGrid System Time. Complete this procedure for all ContentDirectors. IMPORTANT: The following steps must be repeated when replacing a ContentDirector. Initializing Clusters Once the ContentDirector software is running for the first time, it must be initialized to a cluster. All ContentDirectors in one cluster must have the same Cluster ID. For more information about clusters, see About Clusters, Volumes and Groups with the ContentServer 3000 or About Setting up Groups of ContentServers 1000 or 2000 Series, depending on your system. Perform the following steps on each ContentDirector. To initialize the cluster(s): 1. Make sure you are logged on to the ContentDirector with the following credentials: • User name: ovnuser • Password: OVN@SvCaUsa 2. Type the following at the command prompt: cd /home/ovnuser/scripts 3. Start the initialization script with the following command: sudo ./initialize 92 Installation and Configuration Guide
Follow the prompts to initialize the cluster(s). Output similar to the following should appear: Connecting to host "localhost", protocol "tcp", prog 0x20000004 Initializing the cluster The cluster was initialized successfully System Configuration The cluster ID should now be set on the ContentDirector, and the programs should begin to execute in sequence. Verifying Cluster Connectivity To verify cluster connectivity: 1. Make sure that the ContentServers have been acquired by typing the following: sudo /opt/omcld/bin/ssmdiag -s You should output similar to the following: SSID=0 SN=S00007E6A1.0 MGRAID3000 10.4.252.12 10.4.252.15 GB=253/9264 SC=47229 SSID=1 SN=J00007E6A2.0 MGRAID3000 10.4.252.13 10.4.252.16 GB=253/9264 SC=47241 SSID=2 SN=S0000FE6B1.0 MGRAID3000 10.4.252.32 10.4.252.35 GB=253/9264 SC=45606 SSID=3 SN=J0000FE6B2.0 MGRAID3000 10.4.252.33 10.4.252.36 GB=253/9264 SC=47188 2. Verify the output, by doing the following: a. Verify that the correct number of ContentServers have been discovered. b. Verify that all the ContentServers have non-empty serial numbers in the SN=0XXXX column. c. Verify that all the ContentServers have a non-zero pair of IP addresses. If a single IP address is all zeros (0.0.0.0), check the Ethernet connections on that ContentServer. d. Verify that there are no “x”s in the left-most column of the listing. An x indicates that a ContentServer is not responding and is an error condition. If any ContentServer is marked with an “x”, check the physical connections to the ContentServer and that it is powered on. Reissue the “ssmdiag” command. Contact Omneon Technical Support for troubleshooting help if the “x” persists. e. Verify that all ContentServers have 0GB allocated in the GB=0/XXXX column. f. Verify that all ContentServers have 0 slices allocated in the SC=0 column. g. If any ContentServers do not appear to be empty, contact Omneon Technical Support for instructions on clearing those ContentServers. Setting the Omneon MediaGrid System Time Omneon MediaGrid requires a common time reference for all of its components, which is important for file stamps and log messages. Complete the following process to set the system time and to synchronize the components. This command forces the system time to be set against an external NTP server. Omneon, Now Part of Harmonic 93
Page 1 and 2:
Omneon MediaGrid Installation and C
Page 3 and 4:
FCC Compliance This equipment has b
Page 5 and 6:
Parameter Specification Detail Safe
Page 7 and 8:
Parameter Specification Detail EMC
Page 9 and 10:
Network Switch 2924, 2948 and 5406
Page 11 and 12:
CAUTION: Danger of explosion if bat
Page 13 and 14:
• Storage Temperature -104 °F to
Page 15 and 16:
Contents Introduction . . . . . . .
Page 17 and 18:
Contents Private VLANs . . . . . .
Page 19 and 20:
Contents Joining a ContentBridge 10
Page 21 and 22:
Contents About Access Control Lists
Page 23 and 24:
Contents Front Panel View . . . . .
Page 25 and 26:
Omneon MediaGrid Version 3.1.1 Intr
Page 27 and 28:
• Cluster, in the context of an O
Page 29 and 30:
Two models of ContentDirectors are
Page 31 and 32:
Keep in mind the following addition
Page 33 and 34:
1. From Windows, click the Start bu
Page 35 and 36:
1. Add two registry parameters to t
Page 37 and 38:
CHAPTER 1 System Installation with
Page 39 and 40:
ContentBridge (optional) SystemMana
Page 41 and 42:
• Cluster names and device names
Page 43 and 44:
Public VLAN Private VLAN 1 Private
Page 45 and 46:
Public VLAN Private VLAN 1 Private
Page 47 and 48:
16 5x(2+1)+1 500 GB 5 TB 16 5x(2+1)
Page 49 and 50:
System Installation with ContentSer
Page 51 and 52:
Page 53 and 54:
Page 55 and 56:
Page 57 and 58:
Figure 10. ContentServer 3000 and 1
Page 59 and 60:
Page 61 and 62:
Page 63 and 64:
10GbE Switch First Switch Second Sw
Page 65 and 66: Module A To Client Network 10-GbE S
Page 67 and 68: Connecting the ContentBridge System
Page 69 and 70: Connecting the ContentDirectors Sys
Page 71 and 72: Configuring a Stretch Cluster Syste
Page 73 and 74: 10 GbE Module 1 GbE Module Public V
Page 75 and 76: System Installation with ContentSer
Page 77 and 78: CHAPTER 2 System Installation with
Page 79 and 80: ContentBridge (optional) SystemMana
Page 81 and 82: • The VLAN name and ID for the su
Page 83 and 84: The following software installation
Page 85 and 86: Before You Begin System Installatio
Page 87 and 88: To rack mount an Omneon MediaGrid:
Page 89 and 90: Figure 26. Rack Mounting the Conten
Page 91 and 92: Installing the ContentServer Disk D
Page 95 and 96: 2 1 2 1 ID ID Figure 32. ContentSer
Page 103 and 104: 2. Continue connecting any remainin
Page 107 and 108: CHAPTER 3 System Configuration This
Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
Page 111 and 112: System Configuration 4. If you are
Page 113 and 114: 6. Apply power to the ContentServer
Page 115: Notes on Active Directory Configura
Page 119 and 120: Joining an Omneon MediaGrid Cluster
Page 121 and 122: 1. From your SSH terminal, edit /et
Page 123 and 124: A list of users in the domain displ
Page 125 and 126: System Configuration 1. After confi
Page 127 and 128: 4. Type the following commands to r
Page 129 and 130: The expected result is: Domain=[SNV
Page 131 and 132: System Configuration This mount poi
Page 133 and 134: System Configuration c. Replace wi
Page 135 and 136: Modify the file as follows: System
Page 137 and 138: Omneon MediaGrid name ContentDirect
Page 139 and 140: Editing the LDAP Configuration File
Page 141 and 142: System Configuration 4. Create a Sa
Page 143 and 144: Modify the file as follows: System
Page 145 and 146: Figure 43. Server Admin Open Direct
Page 147 and 148: The following is a sample output fr
Page 149 and 150: System Configuration a. Replace dom
Page 151 and 152: System Configuration NOTE: Upon joi
Page 153 and 154: To verify the service: 1. Type the
Page 155 and 156: System Configuration configurations
Page 157 and 158: To configure the amount of memory u
Page 159 and 160: System Configuration 4. Set the val
Page 161 and 162: System Configuration 9. As the tran
Page 163 and 164: The acceptable options are “YES
Page 165 and 166: CHAPTER 4 Installing the File Syste
Page 167 and 168:
Installing the File System Driver s
Page 169 and 170:
Installing the File System Driver 3
Page 171 and 172:
CHAPTER 5 Accessing the Omneon Medi
Page 173 and 174:
Figure 45. Omneon MediaGrid Login A
Page 175 and 176:
Accessing the Omneon MediaGrid •
Page 177 and 178:
Automatically Mounting a File Syste
Page 179 and 180:
11. Click the Browse button and the
Page 181 and 182:
Figure 53. Connect to Omneon MediaG
Page 183 and 184:
Figure 54. Automatic MediaGrid Conn
Page 185 and 186:
Accessing the Omneon MediaGrid Moun
Page 187 and 188:
Table 4. Mount Options (Continued)
Page 189 and 190:
Table 5. Mount Options (Continued)
Page 191 and 192:
Accessing the Omneon MediaGrid To u
Page 193 and 194:
Figure 58. MyDir Properties Accessi
Page 195 and 196:
Accessing the Omneon MediaGrid •
Page 197 and 198:
Using AFP on a Macintosh Client Fol
Page 199 and 200:
Accessing the Omneon MediaGrid For
Page 201 and 202:
CHAPTER 6 Administrative Procedures
Page 203 and 204:
Table 6. mgcopy Values Values Descr
Page 205 and 206:
Figure 60. Firmware Version Selecti
Page 207 and 208:
Administrative Procedures Use the f
Page 209 and 210:
Administrative Procedures 1. From t
Page 211 and 212:
To log on to a ContentDirector: 1.
Page 213 and 214:
3. Type the following two lines at
Page 215 and 216:
Administrative Procedures 1. Attach
Page 217 and 218:
4. Change directory to /mnt, as sho
Page 219 and 220:
CHAPTER 7 Hardware Reference This c
Page 221 and 222:
Figure 67. Rear View of 1010 Networ
Page 223 and 224:
Power, fault and locator LEDs Conso
Page 225 and 226:
Power and fault LEDs Figure 75. Rea
Page 227 and 228:
Table 8. ContentDirector Indicator
Page 229 and 230:
Drive-status Indicator Pattern Cond
Page 231 and 232:
Indicator Pattern Condition Content
Page 233 and 234:
Off White Blue Red Ethernet Port 0
Page 235 and 236:
Link indicator Port 0 Port 1 Figure
Page 237 and 238:
Yellow Power on White Red Ethernet
Page 239 and 240:
Table 21. Drive-status Indicator Pa
Page 241 and 242:
Power Supply LEDs Figure 93 and Tab
Page 243 and 244:
Table 26. ContentServer 1042 Ethern
Page 245 and 246:
Table 29. ContentServer 1042B Rear
Page 247 and 248:
Figure 99. Rear View of ContentServ
Page 249 and 250:
1 PWR RST MediaGrid Figure 101. Con
Page 251 and 252:
Table 34. ContentServer 2122 Front
Page 253 and 254:
2 1 2 1 3 ID Figure 104. ContentSer
Page 255 and 256:
Front Panel Components Front Bezel
Page 257 and 258:
Table 39. ContentServer 2124 Front
Page 259 and 260:
2 1 2 1 3 ID Figure 109. ContentSer
Page 261 and 262:
ContentServer 3000 Hardware Referen
Page 263 and 264:
Left Control Panel Figure 113. Cont
Page 265 and 266:
Table 46. Disk Drive Status LEDs LE
Page 267 and 268:
Table 47. ContentServer 3000 Rear P
Page 269 and 270:
Figure 117. NVRAM Card LEDs 2 1 3 T
Page 271 and 272:
Figure 119. 10 Gigabit Ethernet Add
Page 273 and 274:
1 Drive 15 15 OPEN 14 Figure 121. C
Page 275 and 276:
Table 55. ContentStore 3160 Front B
Page 277 and 278:
Table 57. ContentStore 3160 Rear Pa
Page 279 and 280:
CHAPTER 8 Troubleshooting This sect
Page 281 and 282:
Troubleshooting The dhcp-leases fil
Page 283 and 284:
Troubleshooting The two most import
Page 285 and 286:
Troubleshooting points. The number
Page 287 and 288:
Security with Microsoft Domain Cont
Page 289 and 290:
mdsclientn dialog output: Troublesh
Page 291 and 292:
sessions output: *** 1/64 RPC sessi
Page 293 and 294:
APPENDIX A Legacy Hardware Platform
Page 295 and 296:
Figure 127. ContentDirector Hard Dr
Page 297 and 298:
. Figure 129. ContentDirector Power
Page 299 and 300:
Table 65. ContentDirector Indicator
Page 301 and 302:
Drive-status Indicator Pattern Cond
Page 303 and 304:
1. Link indicator 2. Activity indic
Page 305 and 306:
Figure 139 and Table 72 describe th
Page 307 and 308:
Figure 141. ContentBridge Front Pan
Page 309 and 310:
Table 77. ContentBridge 2010A Ether
Page 311 and 312:
Figure 145. ContentServer 1242 with
Page 313 and 314:
Table 81. ContentServer 1242 Ethern
show all

About Omneon MediaGrid - Harmonic Inc

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?