About Omneon MediaGrid - Harmonic Inc
About Omneon MediaGrid - Harmonic Inc About Omneon MediaGrid - Harmonic Inc
System Configuration • The “hostname” for the Active Directory server • The Active Directory Server's FQDN (Fully Qualified Domain Name) • The IP address for the Active Directory server • The user name and password for a valid user account with administrative privileges Avoiding IP Address Conflicts when Running Configuration Assistant The Omneon MediaGrid installation procedure using the Configuration Assistant assumes that the subnets (private and public) do not contain any pre-existing devices within the final IP-addressing scheme. The Configuration Assistant may attempt to use the “dot-10” address for the first ContentDirector in the installation process. If the SystemManager, or another device, is already installed and configured at the “dot-10” IP address while the Omneon MediaGrid is being configured, the Configuration Assistant may not correctly configure the ContentDirector. If this occurs, once the Configuration Assistant completes and the ContentDirector is restarted, the ContentDirector will display an error message indicating that it “failed to acquire IP address.” To avoid this issue, please wait until after the Configuration Assistant is complete before assigning IP addresses to any locally attached devices like the SystemManager. Note that this only applies when the SystemManager or other such device is placed within the same subnet as the Omneon MediaGrid. For instructions on installing the SystemManager, refer to the Omneon SystemManager Installation Guide. About RAID Set Creation for Systems with the ContentServer 3000 Series Before selecting the RAID set geometry for your system, make sure you have reviewed Supported RAID Configurations. This will help you select the RAID set geometry that best serves your needs. Powering on an Omneon MediaGrid System Make sure all of the Omneon MediaGrid devices are connected before continuing. To power on an Omneon MediaGrid system: 1. Apply power to the Network Switches by plugging the power cords into power sources. 2. Apply power to the SystemManager by connecting the power cord to a power source. Press the Power button on the front of the SystemManager platform. NOTE: If you have already configured the SystemManager with an IP address ending in "dot-10," wait until after the Configuration Assistant is complete before powering on the SystemManager. For more information, refer to Avoiding IP Address Conflicts when Running Configuration Assistant. 3. Apply power to the ContentDirectors by connecting both power cords to separate, isolated power sources. Press the Power button on the front of each ContentDirector. The ContentDirectors take approximately five minutes to start. Wait for the power-on indicator to light before continuing. 4. Apply power to any ContentBridge 2010B/2010C by pressing the Power switch on the front of the device. 5. Apply power to the ContentBridge 1000 (if part of the system) by pressing the Power switch on the back of the device. 88 Installation and Configuration Guide
6. Apply power to the ContentServers as follows: System Configuration • For a system with the ContentServer 3000: a. Apply power to the ContentServers 3000 by connecting the power cords to power sources. Press the Power button on the control panel on the front of the server. b. Apply power to the ContentStores 3160 by connecting the power cords to power sources. Press the Power button on the control panel on the front of each ContentStore. • For the ContentServer 1042, connect the power cords to power sources and then press the power switch on the back of the server. • For the ContentServer 2122/2124, connect the power cords to power sources. There is no power button on this server; the server powers on when connected to a power source. Running the Configuration Assistant Follow these steps to run the configuration assistant. IMPORTANT: Make sure that the completed Omneon MediaGrid Installation Planning Guide is available before continuing. Also make sure you have reviewed the information in Getting Started with the Omneon MediaGrid Configuration Assistant before continuing. To run the configuration assistant: 1. Connect a monitor and keyboard to the first ContentDirector in your Omneon MediaGrid system. CAUTION: Do not attempt to run the Configuration Assistant remotely (for example, via SSH). You must run the Configuration Assistant directly from the ContentDirector in order for it to successfully configure the system. 2. Log on to the ContentDirector using the following user name and password: • User name: ovnuser • Password: OVN@SvCaUsa 3. Run the discover command to verify that the configuration assistant will be able to detect all of the devices in your Omneon MediaGrid system. Enter the following: sudo discover -c Depending on the number of devices in your system, this process may take up to 10 minutes to detect all the devices. See Figure 40. Omneon, Now Part of Harmonic 89
- Page 61 and 62: System Installation with ContentSer
- Page 63 and 64: 10GbE Switch First Switch Second Sw
- Page 65 and 66: Module A To Client Network 10-GbE S
- Page 67 and 68: Connecting the ContentBridge System
- Page 69 and 70: Connecting the ContentDirectors Sys
- Page 71 and 72: Configuring a Stretch Cluster Syste
- Page 73 and 74: 10 GbE Module 1 GbE Module Public V
- Page 75 and 76: System Installation with ContentSer
- Page 77 and 78: CHAPTER 2 System Installation with
- Page 79 and 80: ContentBridge (optional) SystemMana
- Page 81 and 82: • The VLAN name and ID for the su
- Page 83 and 84: The following software installation
- Page 85 and 86: Before You Begin System Installatio
- Page 87 and 88: To rack mount an Omneon MediaGrid:
- Page 89 and 90: Figure 26. Rack Mounting the Conten
- Page 91 and 92: Installing the ContentServer Disk D
- Page 93 and 94: System Installation with ContentSer
- Page 95 and 96: 2 1 2 1 ID ID Figure 32. ContentSer
- Page 97 and 98: System Installation with ContentSer
- Page 99 and 100: System Installation with ContentSer
- Page 101 and 102: System Installation with ContentSer
- Page 103 and 104: 2. Continue connecting any remainin
- Page 105 and 106: System Installation with ContentSer
- Page 107 and 108: CHAPTER 3 System Configuration This
- Page 109 and 110: Password: OVN@SvCaUsa 3. Enter the
- Page 111: System Configuration 4. If you are
- Page 115 and 116: Notes on Active Directory Configura
- Page 117 and 118: Follow the prompts to initialize th
- Page 119 and 120: Joining an Omneon MediaGrid Cluster
- Page 121 and 122: 1. From your SSH terminal, edit /et
- Page 123 and 124: A list of users in the domain displ
- Page 125 and 126: System Configuration 1. After confi
- Page 127 and 128: 4. Type the following commands to r
- Page 129 and 130: The expected result is: Domain=[SNV
- Page 131 and 132: System Configuration This mount poi
- Page 133 and 134: System Configuration c. Replace wi
- Page 135 and 136: Modify the file as follows: System
- Page 137 and 138: Omneon MediaGrid name ContentDirect
- Page 139 and 140: Editing the LDAP Configuration File
- Page 141 and 142: System Configuration 4. Create a Sa
- Page 143 and 144: Modify the file as follows: System
- Page 145 and 146: Figure 43. Server Admin Open Direct
- Page 147 and 148: The following is a sample output fr
- Page 149 and 150: System Configuration a. Replace dom
- Page 151 and 152: System Configuration NOTE: Upon joi
- Page 153 and 154: To verify the service: 1. Type the
- Page 155 and 156: System Configuration configurations
- Page 157 and 158: To configure the amount of memory u
- Page 159 and 160: System Configuration 4. Set the val
- Page 161 and 162: System Configuration 9. As the tran
System Configuration<br />
• The “hostname” for the Active Directory server<br />
• The Active Directory Server's FQDN (Fully Qualified Domain Name)<br />
• The IP address for the Active Directory server<br />
• The user name and password for a valid user account with administrative privileges<br />
Avoiding IP Address Conflicts when Running Configuration Assistant<br />
The <strong>Omneon</strong> <strong>MediaGrid</strong> installation procedure using the Configuration Assistant assumes that the<br />
subnets (private and public) do not contain any pre-existing devices within the final IP-addressing<br />
scheme. The Configuration Assistant may attempt to use the “dot-10” address for the first<br />
ContentDirector in the installation process. If the SystemManager, or another device, is already<br />
installed and configured at the “dot-10” IP address while the <strong>Omneon</strong> <strong>MediaGrid</strong> is being configured,<br />
the Configuration Assistant may not correctly configure the ContentDirector. If this occurs, once the<br />
Configuration Assistant completes and the ContentDirector is restarted, the ContentDirector will<br />
display an error message indicating that it “failed to acquire IP address.” To avoid this issue, please<br />
wait until after the Configuration Assistant is complete before assigning IP addresses to any locally<br />
attached devices like the SystemManager. Note that this only applies when the SystemManager or<br />
other such device is placed within the same subnet as the <strong>Omneon</strong> <strong>MediaGrid</strong>. For instructions on<br />
installing the SystemManager, refer to the <strong>Omneon</strong> SystemManager Installation Guide.<br />
<strong>About</strong> RAID Set Creation for Systems with the ContentServer 3000 Series<br />
Before selecting the RAID set geometry for your system, make sure you have reviewed Supported<br />
RAID Configurations. This will help you select the RAID set geometry that best serves your needs.<br />
Powering on an <strong>Omneon</strong> <strong>MediaGrid</strong> System<br />
Make sure all of the <strong>Omneon</strong> <strong>MediaGrid</strong> devices are connected before continuing.<br />
To power on an <strong>Omneon</strong> <strong>MediaGrid</strong> system:<br />
1. Apply power to the Network Switches by plugging the power cords into power sources.<br />
2. Apply power to the SystemManager by connecting the power cord to a power source. Press the<br />
Power button on the front of the SystemManager platform.<br />
NOTE: If you have already configured the SystemManager with an IP address ending in "dot-10," wait until<br />
after the Configuration Assistant is complete before powering on the SystemManager. For more information,<br />
refer to Avoiding IP Address Conflicts when Running Configuration Assistant.<br />
3. Apply power to the ContentDirectors by connecting both power cords to separate, isolated power<br />
sources. Press the Power button on the front of each ContentDirector. The ContentDirectors take<br />
approximately five minutes to start. Wait for the power-on indicator to light before continuing.<br />
4. Apply power to any ContentBridge 2010B/2010C by pressing the Power switch on the front of the<br />
device.<br />
5. Apply power to the ContentBridge 1000 (if part of the system) by pressing the Power switch on the<br />
back of the device.<br />
88 Installation and Configuration Guide