CMI RII User Manual

More documents

Recommendations

Info

Figure 91: Check In/Check Out dialogThe dialog shows the following:• TC-StateShows the check in/check out, revise state of the dataset in Teamcenter.• ModifiedShows the modification state in CATIA.• FilenameShows the filename.• ResultShows the result for the last action for the file.The following actions are possible:• Refresh from TCRefresh the information from Teamcenter.• Check In/Check OutBefore performing the Check In/Check Out action, the user has to select the filesto be checked in/checked out.• Revise (see section Dataset pseudo Revise)Before performing the Revise action, the user has to select the files to be revised.62 CMI RII User Manual
Dataset pseudo ReviseCMI RII supports the standard Teamcenter behavior for the revise process. That meanswhen an Item Revision is going to be revised the CAD Datasets belonging to can bereferenced by the new revision of the Item Revision (‘Copy As Reference’) or copied(‘Copy As Object’). With “Copy As Reference” the Dataset is write protected.In order to be able to modify the CAD Datasets in CATIA the CAD Dataset must be“pseudo Revised”. Though, a revise is only possible under certain conditions:• The CAD Dataset is referenced by a predecessor of the current Item Revision.• The Item Revision B has “working” state and the user has write access to theItem Revision.• If the CAD Dataset has “working” state a revise of the dataset is not required andwill not be offered therefore.• Only primary CAD Datasets can be revised: CMI3DGeo, CMIAux3DGeo,CMIStructure or CMI2DGeo.• Only CAD Datasets that are attached to an Item/Part can be revised.If these conditions are true then:• Creation of a new CAD Dataset /B.• Copy of the named Reference (the CATPart) from the CAD Dataset /A.• Copy of attributes from CAD Dataset /A.• Removal of Relationship between Item Revision /B and CAD Dataset /A.• The CAD Dataset /B will be attached to Item Revision /B.• Optionally (with CMI preference setting): Automatic Check Out of the newDataset revision.Item Rev AItem Rev B(3) DeleteData Set ARelationshipItem ID.CATPart(2) Create ofRelationship(1) CopyData Set BItem Rev BData Set BItem ID.CATPartItem ID.CATPartFigure 92: General Process of “Pseudo Revise” for CAD DatasetsCMI RII User Manual 63
Page 1 and 2:
CATIATeamcenterInterfaceRIICMI RII
Page 3 and 4:
PrefaceThis manual describes the ma
Page 5 and 6:
Table of ContentsCHAPTER 1.........
Page 7 and 8:
Table of FiguresFIGURE 1: CATIA TEA
Page 9 and 10:
CHAPTER 1OverviewThis chapter provi
Page 11:
CHAPTER 2Getting StartedThis chapte
Page 14 and 15:
A window with the CMI RII applicati
Page 16 and 17:
Menu item WindowFigure 9: CMI RII a
Page 18 and 19:
Figure 13: Context menu on a Datase
Page 20 and 21: Only the expanded structures from t
Page 23 and 24: CHAPTER 4CATIA relevant Objects inT
Page 25 and 26: The figure below shows an example a
Page 27 and 28: Figure 27: My Teamcenter applicatio
Page 29 and 30: Figure 31: CATIA V5 with loaded “
Page 31: Figure 35: Highlight in CATIA in Po
Page 34 and 35: Read from TeamcenterUpdate Teamcent
Page 36 and 37: CMI toolbar: Update TeamcenterThis
Page 38 and 39: Figure 43: Edit new PDM-Part catego
Page 40 and 41: If you want to highlight CATParts,
Page 42 and 43: Revision A and B of your assembly a
Page 44 and 45: In the CMI Reconnect Dialog, click
Page 46 and 47: Create the CATDrawing with the usua
Page 48 and 49: Handling of cgr and model filesCATI
Page 50 and 51: Figure 54: Bolt Catalog opened in C
Page 52 and 53: Figure 57: Synchronize Catalog dial
Page 54 and 55: Handling of CMI ArchivesCMI support
Page 56 and 57: After the update the user gets the
Page 58 and 59: To add some files press the “Add
Page 60 and 61: Figure 71: CMI Product with existin
Page 62 and 63: Handling of Design TablesCATIA V5 D
Page 64 and 65: Figure 79: Design Table object in T
Page 66 and 67: Figure 85: CATPart without Design T
Page 68 and 69: Update PositionTo enable this funct
Page 73 and 74: GlossaryAdministratorPerson, who co
show all

CMI RII User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?