CMI RII User Manual

More documents

Recommendations

Info

Figure 57: Synchronize Catalog dialogFor new catalogs that were not already opened from Teamcenter, the user canchange the file name which should be used in Teamcenter.The type can be Open, Open as copy, and Instantiate. These types describe theway in which the items will be handled when the catalog is used with the ManageCatalogs command.OpenOpen as copyInstantiateOpen the referenced object in CATIA so that theexisting Teamcenter item is used (e.g. standard part).Open the referenced object in CATIA so that it will berecognized as a new item in Teamcenter (e.g.templates).Instantiate is used for Features and Power copies whichwill be instantiated in the active document.The Status Field can be Loaded by CMI, Updated by CMI, Not known by CMI,and Created by CMI.Loaded by CMIUpdated by CMINot Known by CMICreated by CMIThe item is from Teamcenter and already was in thecatalog at load time.The item is from Teamcenter but the type was changed.The item is not from Teamcenter.The referenced file was opened from Teamcenter andis new in the catalog.After pressing the Synchronize icon CMI will check all entries and if there areunknown entries, the user must confirm, that he will continue.44 CMI RII User Manual
Figure 58: Confirmation dialog for unknown entries in the synchronize catalogcommandThis indicates that there is an item referenced in the catalog that is not managed byTeamcenter.Next the catalog is registered or updated in Teamcenter.Figure 59 is shown when the Synchronize command ends successfully.Figure 59: Synchronize Catalog with successCMI RII User Manual 45
Page 1 and 2: CATIATeamcenterInterfaceRIICMI RII
Page 3 and 4: PrefaceThis manual describes the ma
Page 5 and 6: Table of ContentsCHAPTER 1.........
Page 7 and 8: Table of FiguresFIGURE 1: CATIA TEA
Page 9 and 10: CHAPTER 1OverviewThis chapter provi
Page 11: CHAPTER 2Getting StartedThis chapte
Page 14 and 15: A window with the CMI RII applicati
Page 16 and 17: Menu item WindowFigure 9: CMI RII a
Page 18 and 19: Figure 13: Context menu on a Datase
Page 20 and 21: Only the expanded structures from t
Page 23 and 24: CHAPTER 4CATIA relevant Objects inT
Page 25 and 26: The figure below shows an example a
Page 27 and 28: Figure 27: My Teamcenter applicatio
Page 29 and 30: Figure 31: CATIA V5 with loaded “
Page 31: Figure 35: Highlight in CATIA in Po
Page 34 and 35: Read from TeamcenterUpdate Teamcent
Page 36 and 37: CMI toolbar: Update TeamcenterThis
Page 38 and 39: Figure 43: Edit new PDM-Part catego
Page 40 and 41: If you want to highlight CATParts,
Page 42 and 43: Revision A and B of your assembly a
Page 44 and 45: In the CMI Reconnect Dialog, click
Page 46 and 47: Create the CATDrawing with the usua
Page 48 and 49: Handling of cgr and model filesCATI
Page 50 and 51: Figure 54: Bolt Catalog opened in C
Page 54 and 55: Handling of CMI ArchivesCMI support
Page 56 and 57: After the update the user gets the
Page 58 and 59: To add some files press the “Add
Page 60 and 61: Figure 71: CMI Product with existin
Page 62 and 63: Handling of Design TablesCATIA V5 D
Page 64 and 65: Figure 79: Design Table object in T
Page 66 and 67: Figure 85: CATPart without Design T
Page 68 and 69: Update PositionTo enable this funct
Page 70 and 71: Figure 91: Check In/Check Out dialo
Page 73 and 74: GlossaryAdministratorPerson, who co

CMI RII User Manual

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?