SyntronÂ® Electromagnetic Feeders - FMC Technologies

More documents

Recommendations

Info

Syntron ® Electromagnetic FeedersSyntron ® Heavy-Duty Electromagnetic FeedersBulk material feeding with full-range control.Syntron ® Heavy-Duty ElectromagneticFeeders come in tendifferent models with capacitiesranging from 25 to 1600 tons perhour.* These versatile feeders arecapable of handling a variety ofmaterials from the finest powdersto large, coarse particles.Syntron Electromagnetic Feederscan be supplied in various configurationsincluding multiple- driveunits and above-deck drive units.Above-deck drive units are recommendedwhere there is insufficientspace below the trough.Syntron Electromagnetic Feedersrequire minimal maintenance asthere are no mechanical parts to wearout, such as cams, eccentrics, beltsand bearings – thus eliminating theneed for lubrication. All movementis confined to the heavy-duty leafsprings. Electrical components, suchas the coil, will provide years ofservice under normal operatingconditions. Dust-tight drive unitsare standard on all models.Dependable, flexible controls provideeasily adjustable feed rates withinstantaneous response. A varietyof controls with special controlarrangements are available.(For more information onelectromagnetic feeder controls,see pages 26 - 28.)Syntron ®F-450 Electromagnetic Feeders feed sand in a glass factory.Electromagnetic Feeder Features■ Dust-tight and maintenance-free drive units■ Above- or below-deck drive units■ Two-mass, spring-connected, sub-resonant tuned■ High frequency - 3600 VPM at 60Hz■ Stroke - 0.060 inches■ Stroke generated by creating a magnetic field■ Suspension mount, base mount or combination of both■ Bolt-in replacement trough liners■ Multiple-drive unit feeders available* Based on dry sand weighing 100 pounds per cubic foot. Capacities vary depending on drive unit location, material characteristics, materialdensity, trough length and width, trough liner type, feeder installation, skirt boards and hopper transitions.4
Syntron ® F-380 Electromagnetic Feeder with above-deckdrive unit evenly distributes parts at a consistent rate toa heat treatment furnace.Feeding gypsum with Syntron model F-380Electromagnetic Feeder.Syntron ® ElectromagneticFeeders are normally installedby suspension mounting withfour flexible wire rope cables.They can also be supplied forbase mounting on a solid base,or with a combination of basemounting and suspensionmounting.Syntron Electromagnetic Feeders are ideal for use in a stationary operation suchas a tunnel system from a surge pile. They are usually controlled from a remotepoint to provide the desired feed rate. In this application,a model FH-22 feeds limestone to a belt conveyor.Material Handling Solutions5www.fmctechnologies.com/materialhandling
Page 1 and 2: Heavy Duty Feeders
Page 3 and 4: table of contentsSyntron ® Heavy-d
Page 5: Syntron ® Heavy-Duty Vibrating Fee
Page 9 and 10: Electromagnetic Feeder Specificatio
Page 12 and 13: Syntron ® Electromagnetic Feeders
Page 14 and 15: Syntron ® Electromagnetic Feeders
Page 16 and 17: Syntron ® Electromechanical Feeder
Page 18 and 19: Syntron ® RF Electromechanical Fee
Page 20 and 21: Syntron ® MF Electromechanical Fee
Page 28 and 29: Syntron ® Feeder ControlsSyntron
Page 30 and 31: Syntron ® Feeder Controls (cont’
Page 32 and 33: Recommended InstallationRecommended
Page 34 and 35: Recommended Installation (cont’d.
Page 39 and 40: Syntron ® serviceand supportAt FMC

SyntronÂ® Electromagnetic Feeders - FMC Technologies

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?