Improvised Munitions Handbook (Improvised Explosive Devices or ...
Improvised Munitions Handbook (Improvised Explosive Devices or ... Improvised Munitions Handbook (Improvised Explosive Devices or ...
6.11 Short Term Time Delay for Grenade A simple modification can produce delays of approximately 12 seconds for grenades when fired from Grenade Launchers (section 4.5). Materials Required Grenade Nail Knife May not be needed Pliers Safety fuse Note: Any safety or improvised fuse may be used. However, since different time delays will result, determine the burning rate of the fuse first. Procedure 1. Unscrew fuse mechanism from body of grenade and remove. Pliers may have to be used. 2. Carefully cut with knife or break off detonator at crimp and save for later use. Caution: If detonator is cut or broken below the crimp, detonation may occur and severe injuries could result.
3. Remove safety pin pull ring and lever, letting striker hit the primer. Place fuse mechanism aside until delay fuse powder mix in mechanism is completely burned. 4. Remove pin, spring, and striker. 5. Remove primer from fuse mechanism by pushing nail through bottom end of primer hole and tapping with hammer.
- Page 171 and 172: Caution: Lye solution can burn skin
- Page 173 and 174: Note: Do not get the yellow egg yol
- Page 175 and 176: natural waxes which have suspended
- Page 177 and 178: 4. Form a tube from cardboard just
- Page 179 and 180: After a time delay, the acid will e
- Page 181 and 182: 4. Add 12 tablespoons of shellac to
- Page 183 and 184: 1. Separate a handful of steel wool
- Page 185 and 186: 5.8 Improvised Yellow Flare A yello
- Page 187 and 188: 6. Mix ingredients thoroughly by fo
- Page 189 and 190: 12. Knot one end of the fuse and pl
- Page 191 and 192: 1. Measure 3 level tablespoons of p
- Page 193 and 194: 8. Remove lid from quart jar and ad
- Page 195 and 196: 5. Place the fused white flare mix
- Page 197 and 198: 6. Place all ingredients on the win
- Page 199 and 200: 10. Just before use as a black smok
- Page 201 and 202: Improvised Munitions Handbook (Impr
- Page 203 and 204: 5. Fill the tube with black powder
- Page 205 and 206: 4. Fold matches over fuse and tape.
- Page 207 and 208: Cigarette Paper match String (shoel
- Page 209 and 210: Procedure 1. If watch has a sweep o
- Page 211 and 212: 3. Enlarge the hole in the plug exc
- Page 213 and 214: . Measure the time it takes for the
- Page 215 and 216: 6.7 Fuse Cords These fuse cords are
- Page 217 and 218: Materials Required Spring type clot
- Page 219 and 220: 6.9 Time Delay Grenade This delay m
- Page 221: 3. Secure the wire in place across
- Page 225 and 226: Note: If time delay is used for Imp
- Page 227 and 228: Caution: Use extreme care—sudden
- Page 229 and 230: 9. Place safety fuse in delay fuse
- Page 231 and 232: 4. Load the primary explosive in th
- Page 233 and 234: Note: Tamping is not needed when TA
- Page 235 and 236: 2. Wind one scraped wire tightly on
- Page 237 and 238: 2. Retract the striker of the mouse
- Page 239 and 240: 2. Strip insulation from the end of
- Page 241 and 242: 7.4 Metal Ball Switch This switch w
- Page 243 and 244: 4. Place metal ball on block so tha
- Page 245 and 246: 3. Strip insulation from the ends o
- Page 247 and 248: 1. Separate loops by about 2 inches
- Page 249 and 250: 3. Tie a piece of thread around the
- Page 251 and 252: 4. Insert safety fuse in hole. Be s
- Page 253 and 254: 7.11 Automobile Generator Power Sou
- Page 255 and 256: 2. Place one foot on the generator
- Page 257 and 258: How to Use 1. Just prior to use (no
- Page 259 and 260: Ammonium chloride (sal ammoniac) (s
- Page 261 and 262: made by hooking the wire through ho
- Page 263 and 264: It is a more efficient detonating a
- Page 265 and 266: A2.4 RDX TM 9-1900, Ammunition, Gen
- Page 267 and 268: A2.10 Blasting Gelatin Description
- Page 269 and 270: Improvised Munitions Handbook (Impr
- Page 271 and 272: 089 non-electrical nonelectrical 09
3. Remove safety pin pull ring and lever, letting striker hit<br />
the primer. Place fuse mechanism aside until delay fuse<br />
powder mix in mechanism is completely burned.<br />
4. Remove pin, spring, and striker.<br />
5. Remove primer from fuse mechanism by pushing<br />
nail through bottom end of primer hole and tapping<br />
with hammer.