Improvised Munitions Handbook (Improvised Explosive Devices or ...
Improvised Munitions Handbook (Improvised Explosive Devices or ... Improvised Munitions Handbook (Improvised Explosive Devices or ...
6.2 Fuse Igniter from Book Matches A simple, reliable fuse igniter can be made from paper book matches. Materials Required Paper book matches Adhesive or friction tape Fuse cord (improvised or commercial) Pin or small nail Procedure 1. Remove the staple(s) from match book and separate matches from cover. 2. Cut fuse cord so that inner core is exposed. 3. Tape exposed end of fuse cord in center of one row of matches.
4. Fold matches over fuse and tape. 5. Shape the cover into a tube with the striking surface on the inside and tape. Make sure the edges of the cover at the striking end are butted. Leave cover open at opposite end for insertion of the matches. 6. Push the taped matches with fuse cord into the tube until the bottom ends of the matches are exposed about 3/4 inch (2 cm). 7. Flatten and fold the open end of the tube so that it laps over about 1 inch (2-1/2 cm); tape in place.
- Page 153 and 154: 1. Drill small hole through center
- Page 155 and 156: Note: The 14 inch launcher may be h
- Page 157 and 158: 3. Place bolt through hole in end c
- Page 159 and 160: 150 25 40 0 300 50 40 1 700 150 40
- Page 161 and 162: 2. Remove the acid from heat and al
- Page 163 and 164: 4. Push the taped matches into the
- Page 165 and 166: 2. Cut 2 slots on opposite sides of
- Page 167 and 168: 8. Punch many closely spaced small
- Page 169 and 170: 5.4.3 Soap-Alcohol System 5.4.4 Egg
- Page 171 and 172: Caution: Lye solution can burn skin
- Page 173 and 174: Note: Do not get the yellow egg yol
- Page 175 and 176: natural waxes which have suspended
- Page 177 and 178: 4. Form a tube from cardboard just
- Page 179 and 180: After a time delay, the acid will e
- Page 181 and 182: 4. Add 12 tablespoons of shellac to
- Page 183 and 184: 1. Separate a handful of steel wool
- Page 185 and 186: 5.8 Improvised Yellow Flare A yello
- Page 187 and 188: 6. Mix ingredients thoroughly by fo
- Page 189 and 190: 12. Knot one end of the fuse and pl
- Page 191 and 192: 1. Measure 3 level tablespoons of p
- Page 193 and 194: 8. Remove lid from quart jar and ad
- Page 195 and 196: 5. Place the fused white flare mix
- Page 197 and 198: 6. Place all ingredients on the win
- Page 199 and 200: 10. Just before use as a black smok
- Page 201 and 202: Improvised Munitions Handbook (Impr
- Page 203: 5. Fill the tube with black powder
- Page 207 and 208: Cigarette Paper match String (shoel
- Page 209 and 210: Procedure 1. If watch has a sweep o
- Page 211 and 212: 3. Enlarge the hole in the plug exc
- Page 213 and 214: . Measure the time it takes for the
- Page 215 and 216: 6.7 Fuse Cords These fuse cords are
- Page 217 and 218: Materials Required Spring type clot
- Page 219 and 220: 6.9 Time Delay Grenade This delay m
- Page 221 and 222: 3. Secure the wire in place across
- Page 223 and 224: 3. Remove safety pin pull ring and
- Page 225 and 226: Note: If time delay is used for Imp
- Page 227 and 228: Caution: Use extreme care—sudden
- Page 229 and 230: 9. Place safety fuse in delay fuse
- Page 231 and 232: 4. Load the primary explosive in th
- Page 233 and 234: Note: Tamping is not needed when TA
- Page 235 and 236: 2. Wind one scraped wire tightly on
- Page 237 and 238: 2. Retract the striker of the mouse
- Page 239 and 240: 2. Strip insulation from the end of
- Page 241 and 242: 7.4 Metal Ball Switch This switch w
- Page 243 and 244: 4. Place metal ball on block so tha
- Page 245 and 246: 3. Strip insulation from the ends o
- Page 247 and 248: 1. Separate loops by about 2 inches
- Page 249 and 250: 3. Tie a piece of thread around the
- Page 251 and 252: 4. Insert safety fuse in hole. Be s
- Page 253 and 254: 7.11 Automobile Generator Power Sou
6.2 Fuse Igniter from Book Matches<br />
A simple, reliable fuse igniter can be made from paper book matches.<br />
Materials Required<br />
Paper book matches<br />
Adhesive <strong>or</strong> friction tape<br />
Fuse c<strong>or</strong>d (improvised <strong>or</strong> commercial)<br />
Pin <strong>or</strong> small nail<br />
Procedure<br />
1. Remove the staple(s) from match book and separate<br />
matches from cover.<br />
2. Cut fuse c<strong>or</strong>d so that inner c<strong>or</strong>e is exposed.<br />
3. Tape exposed end of fuse c<strong>or</strong>d in center of one<br />
row of matches.