Improvised Munitions Handbook (Improvised Explosive Devices or ...
Improvised Munitions Handbook (Improvised Explosive Devices or ... Improvised Munitions Handbook (Improvised Explosive Devices or ...
2. Fold one end of 1 inch x 12 inch rag 3 times so that it becomes a one inch square of 3 thicknesses. Place rag into pipe to cover match heads, folded end first. Tamp firmly with caution. 3. Place metal object into pipe. Place 1 inch x 3 inch rag into pipe to cover projectile. Tamp firmly with caution. 4. Place 2 toy caps over small hole in end cap. Be sure metal strap will hit caps when it is released. Note: It may be necessary to tape toy caps to end cap. 5. When ready to fire, pull metal strap back and release. B. When “Strike-Anywhere” Matches Are Available:
1. Follow steps 1 through 3 in A. 2. Carefully cut off tips of heads of 2 “strike-anywhere” matches with knife. 3. Place one tip in hole in end cap. Push in with wooden end of match stick. 4. Place second match tip on a piece of tape. Place tape so match tip is directly over hole in end cap. 5. When ready to fire, pull metal strap back and release. C. When Safety Fuse Is Available: (Recommended for Booby Traps) 1. Remove end cap from pipe. Knot one end of safety fuse. Thread safety fuse through hole in end cap so that knot is on inside of end cap. 2. Follow steps 1 through 3 in A. 3. Tie several matches to safety fuse near outside of end cap. Note: Bare end of safety fuse should be inside match head cluster.
- Page 75 and 76: 2. Screw pipe cap to one and of pip
- Page 77 and 78: 2. Tape, tie or glue one or two row
- Page 79 and 80: 2. Ignite the string and allow to b
- Page 81 and 82: 2.4 Grenade-Tin Can Land Mine This
- Page 83 and 84: Materials Required Iron pipe approx
- Page 85 and 86: 2. Connect firing leads to battery
- Page 87 and 88: 1. Place plug in mouth of bottle. 2
- Page 89 and 90: 1. Crimp cap around fuse. Caution:
- Page 91 and 92: c. d. e. f. Place large pipe on fla
- Page 93 and 94: Funnel(s) (glass, steel, or aluminu
- Page 95 and 96: Material Funnels inches metric inch
- Page 97 and 98: 1. If pipe is used: a. Place the pi
- Page 99 and 100: Caution: Do not place blasting cap
- Page 101 and 102: 3. Drill a 25/64 inch (1 cm) diamet
- Page 103 and 104: Note: If 9/16 inch drill is not ava
- Page 105 and 106: . Release strap. 3. To Remove Shell
- Page 107 and 108: lacquer after each layer. 6. Drill
- Page 109 and 110: 3. Attach a long cord to the firing
- Page 111 and 112: 2. Pour shot from shell. 3. Replace
- Page 113 and 114: Pipe wrench Shellac or lacquer Elas
- Page 115 and 116: 11. Position metal strap on stock s
- Page 117 and 118: 3.5 Reusable Primer A method of mak
- Page 119 and 120: 9. Place cup in pocket with mixture
- Page 121 and 122: 8. (Optional) Bend bolt for trigger
- Page 123 and 124: Bolt, 3/32 inch (2-1/2 mm) or small
- Page 125: 11. Place screw on each side of sto
- Page 129 and 130: Note: Number of matches and size of
- Page 131 and 132: 3.9 Pipe Pistol for .38 Caliber Amm
- Page 133 and 134: a. Make sure that there are no crac
- Page 135 and 136: Table I Low Signature System Dimens
- Page 137 and 138: further reduce the signature of the
- Page 139 and 140: Note: Be sure that the water pipe h
- Page 141 and 142: 3. Drill a hole through the center
- Page 143 and 144: 11. Replace the 12 gauge cardboard
- Page 145 and 146: Caution: 8 grams of black powder yi
- Page 147 and 148: 3. Place free end of fuse and black
- Page 149 and 150: 1. Drill hole in center of wood blo
- Page 151 and 152: 8. Insert rag into front of shotgun
- Page 153 and 154: 1. Drill small hole through center
- Page 155 and 156: Note: The 14 inch launcher may be h
- Page 157 and 158: 3. Place bolt through hole in end c
- Page 159 and 160: 150 25 40 0 300 50 40 1 700 150 40
- Page 161 and 162: 2. Remove the acid from heat and al
- Page 163 and 164: 4. Push the taped matches into the
- Page 165 and 166: 2. Cut 2 slots on opposite sides of
- Page 167 and 168: 8. Punch many closely spaced small
- Page 169 and 170: 5.4.3 Soap-Alcohol System 5.4.4 Egg
- Page 171 and 172: Caution: Lye solution can burn skin
- Page 173 and 174: Note: Do not get the yellow egg yol
- Page 175 and 176: natural waxes which have suspended
2. Fold one end of 1 inch x 12 inch rag 3 times so that it<br />
becomes a one inch square of 3 thicknesses. Place rag into pipe<br />
to cover match heads, folded end first. Tamp firmly with<br />
caution.<br />
3. Place metal object into pipe. Place 1 inch x 3 inch rag into pipe to cover projectile. Tamp firmly with<br />
caution.<br />
4. Place 2 toy caps over small hole in end cap.<br />
Be sure metal strap will hit caps when it is<br />
released.<br />
Note: It may be necessary to tape toy caps to end<br />
cap.<br />
5. When ready to fire, pull metal strap back and release.<br />
B. When “Strike-Anywhere” Matches Are Available: