Improvised Munitions Handbook (Improvised Explosive Devices or ...
Improvised Munitions Handbook (Improvised Explosive Devices or ... Improvised Munitions Handbook (Improvised Explosive Devices or ...
1. To Load: a. b. c. 2. To Fire: a. b. Remove plug from coupling. Put cartridge into pipe. Screw plug hand tight into coupling. Pull strap back and hold with thumb. Release strap. 3. To Unload Gun: a. Take plug out of coupling. b. Drive out used case using stick or twig.
3.5 Reusable Primer A method of making a previously fired primer reusable. Materials Required Used cartridge case 2 long nails having approximately the same diameter as the inside of the primer pocket “Strike-anywhere” matches – 2 or 3 are needed for each primer Vise Hammer Knife or other sharp edged instrument Procedure 1. File one nail to a needle point so that it is small enough to fit through hole in primer pocket. 2. Place cartridge case and nail between jaws of vise. Force out fired primer with nail as shown:
- Page 65 and 66: Caution: Handle dry explosive with
- Page 67 and 68: 3. 4. Strip about 4 inches of insul
- Page 69 and 70: 1.24 Mercury Fulminate Mercury fulm
- Page 71 and 72: 6. 7. Wash the crystals with 6 teas
- Page 73 and 74: 3. Pour mixture into pipe. 4. Inser
- Page 75 and 76: 2. Screw pipe cap to one and of pip
- Page 77 and 78: 2. Tape, tie or glue one or two row
- Page 79 and 80: 2. Ignite the string and allow to b
- Page 81 and 82: 2.4 Grenade-Tin Can Land Mine This
- Page 83 and 84: Materials Required Iron pipe approx
- Page 85 and 86: 2. Connect firing leads to battery
- Page 87 and 88: 1. Place plug in mouth of bottle. 2
- Page 89 and 90: 1. Crimp cap around fuse. Caution:
- Page 91 and 92: c. d. e. f. Place large pipe on fla
- Page 93 and 94: Funnel(s) (glass, steel, or aluminu
- Page 95 and 96: Material Funnels inches metric inch
- Page 97 and 98: 1. If pipe is used: a. Place the pi
- Page 99 and 100: Caution: Do not place blasting cap
- Page 101 and 102: 3. Drill a 25/64 inch (1 cm) diamet
- Page 103 and 104: Note: If 9/16 inch drill is not ava
- Page 105 and 106: . Release strap. 3. To Remove Shell
- Page 107 and 108: lacquer after each layer. 6. Drill
- Page 109 and 110: 3. Attach a long cord to the firing
- Page 111 and 112: 2. Pour shot from shell. 3. Replace
- Page 113 and 114: Pipe wrench Shellac or lacquer Elas
- Page 115: 11. Position metal strap on stock s
- Page 119 and 120: 9. Place cup in pocket with mixture
- Page 121 and 122: 8. (Optional) Bend bolt for trigger
- Page 123 and 124: Bolt, 3/32 inch (2-1/2 mm) or small
- Page 125 and 126: 11. Place screw on each side of sto
- Page 127 and 128: 1. Follow steps 1 through 3 in A. 2
- Page 129 and 130: Note: Number of matches and size of
- Page 131 and 132: 3.9 Pipe Pistol for .38 Caliber Amm
- Page 133 and 134: a. Make sure that there are no crac
- Page 135 and 136: Table I Low Signature System Dimens
- Page 137 and 138: further reduce the signature of the
- Page 139 and 140: Note: Be sure that the water pipe h
- Page 141 and 142: 3. Drill a hole through the center
- Page 143 and 144: 11. Replace the 12 gauge cardboard
- Page 145 and 146: Caution: 8 grams of black powder yi
- Page 147 and 148: 3. Place free end of fuse and black
- Page 149 and 150: 1. Drill hole in center of wood blo
- Page 151 and 152: 8. Insert rag into front of shotgun
- Page 153 and 154: 1. Drill small hole through center
- Page 155 and 156: Note: The 14 inch launcher may be h
- Page 157 and 158: 3. Place bolt through hole in end c
- Page 159 and 160: 150 25 40 0 300 50 40 1 700 150 40
- Page 161 and 162: 2. Remove the acid from heat and al
- Page 163 and 164: 4. Push the taped matches into the
- Page 165 and 166: 2. Cut 2 slots on opposite sides of
1. To Load:<br />
a.<br />
b.<br />
c.<br />
2. To Fire:<br />
a.<br />
b.<br />
Remove plug from coupling.<br />
Put cartridge into pipe.<br />
Screw plug hand tight into coupling.<br />
Pull strap back and hold with thumb.<br />
Release strap.<br />
3. To Unload Gun:<br />
a.<br />
Take plug out of coupling.<br />
b.<br />
Drive out used case using stick <strong>or</strong> twig.
Change language