Answer Solutions Specification Guide - OEC Business Interiors

Universal Freestanding WorksurfacesRound, Square, andRectangle WorksurfacesProduct DetailsLaminate Worksurfaces3 /8"P-edge profile risesslightly above the laminatesurface and curves into a3⁄8" radius which optimizesergonomic benefit for theuser.Edge is available in sixvinyl (plastic) colors. Vinyl(plastic) color is specifiedseparately from laminatecolor.Wood VeneerWorksurfacesSquare (3 mm) Taperededge profile edge profile3 /8"P-edge profileEdges of worksurfacesare available in three profiles—square(3 mm),tapered, and P-edge.Square (3 mm) edgeprofile is achieved byadding wood veneer surfacesto worksurface core.This technique can beapplied to worksurfaces thatare straight or curved..Tapered edge profile isachieved by rolling woodveneer surface aroundshaped edge of worksurfacecore. Tapered edge profileslopes toward the user forenhanced comfort.P-edge profile isachieved by adding a P-shaped vinyl (plastic) edgeto the worksurface core.P-edge profile provides asoft, durable interface forthe user and is available inblack only.ConnectionsRound, square, andrectangle worksurfacesare freestanding andare supported by legs. Legsare ordered separately andinstalled in the field.Tip: Use the Worksurfaceand Leg Combinationsmatrix to determine the typeand number of legs youneed to order for the worksurfaceyou choose.cPage 178..Underside of worksurfacehas inset locationsthat support slip-fit and nestingapplications and allowlegs to be positioned in a45° orientation. Amount ofslip-fit varies by worksurfaceshape and size.cSee Worksurface LegPositions, page 179.Primary worksurfacewith 28 1 ⁄2"H legs installed at6" or 9" inset can slip overadjacent worksurfaces thatare supported with 26"Hlegs.26"H legs allow worksurfacesto nest underneath anadjacent worksurface with28 1 ⁄2"H legs or a panelmountedworksurface.Reinforcing brace isused to support all worksurfacesthat are wider than60"W. Brace(s) are includedwith rectangle worksurfacesand are field-installed. Wheninstalled, brace adds 1"below worksurface. Onebrace is shipped with 72"W,two with 84"W, and threewith 96"W worksurfaces.Surface MaterialsLaminate Worksurfaces• Laminate• Accent laminate (option)A family of pre-approved,non-Steelcase laminatesthat reflect the latest trendsin color.cSee Surface MaterialsReference Manual.• Open Line laminate(option)A program including non-Steelcase laminates whichare suitable for use onSteelcase products.cSee Surface MaterialsReference Manual.Edge• Vinyl (plastic)Wood VeneerWorksurfaces• Wood veneer (standard)• Customiz stain (option)• Full-fill finish (option)Square (3 mm) ortapered edge profile• Wood veneer to matchworksurfaceP-edge profile• Vinyl (plastic):6000 Black onlyCorian ®• Freestanding Worksurfacesare available in solid surfaceDupont Corian. ® Topsare ordered directly fromTFI, the industry leadingproducer of Dupont Corianproducts.cSee Additional Resources,page 4...Application TopicsMobile pedestals upto 24 1 ⁄2"H will fit under26"H worksurfaces withoutbracing.Mobile pedestals up to27"H will fit under 28 1 ⁄2"Hworksurfaces without bracing.Worksurfaces with reinforcingbrace will reducethe available space by 1".Worksurface and LegCombinationscPage 178Worksurface LegPositionscPage 179Wiring and CablingAccessoriescPage 212ShippingPalletizing streamlinesunloading and staging ofworksurfaces. Identicalworksurfaces ordered on thesame line item are packedon pallets containing 10–20worksurfaces. Remainingworksurfaces are packedindividually in cartons. If palletizingis not desired, orderin quantities of nine or lessper line item. For maximumunload efficiency, utilizepallet handling equipment atjob site whenever possible.Wood veneer worksurfacescannot be palletized..WorksurfacesAnswer Solutions Specification Guide 169