Answer Solutions Specification Guide - OEC Business Interiors

Universal Freestanding WorksurfacesExtended Corner, Straight-Front and Corner, 120°WorksurfacesProduct DetailsLaminate Worksurfaces3 /8"P-edge profile risesslightly above the laminatesurface and curves into a3⁄8" radius which optimizesergonomic benefit for theuser.Edge is available in sixvinyl (plastic) colors. Vinyl(plastic) color is specifiedseparately from laminatecolor.Wood VeneerWorksurfacesSquare (3 mm) Taperededge profile edge profile3 /8"P-edge profileEdges of worksurfacesare available in three profiles—square(3 mm),tapered, and P-edge.Square (3 mm) edgeprofile is achieved byadding wood veneer surfacesto worksurface core.This technique can beapplied to worksurfaces thatare straight or curved..Left-hand UnitRight-hand Unit.Tapered edge profile isachieved by rolling woodveneer surface aroundshaped edge of worksurfacecore. Tapered edge profileslopes toward the user forenhanced comfort.P-edge profile isachieved by adding a P-shaped vinyl (plastic) edgeto the worksurface core.P-edge profile provides asoft, durable interface forthe user and is available inblack only.Extended corner,straight-front worksurfacesare available in leftandright-hand versions..ConnectionsCorner worksurfacesare freestanding and aresupported by legs. Legs areordered separately andinstalled in the field.Tip: Use the Worksurfaceand Leg Combinationsmatrix to determine the typeand number of legs youneed to order for the worksurfaceyou choose.cPage 178Tip: Corner worksurfacesrequire a leg to support theback corner of worksurface.Reinforcing brace isused to support all extendedcorner, straight-front worksurfacesthat are wider than60"W. When installed, braceadds 1" below worksurface.One brace is included withapplicable extended corner,straight-front worksurfacesand is field-installed.Underside of worksurfacehas inset locationsthat support slip-fit and nestingapplications. Cabby legscan be positioned in a 45° or90° orientation. Post legsare positioned in 45° orientationonly.cSee Worksurface LegPositions, page 179..90° orientation45° orientationLegs installed in a90° orientation allow forgreater storage and kneespacebelow the worksurface.45° leg orientation isa preferred aesthetic formany customers. Cabbylegs installed at a 45° orientationwill appear to havemore curvature when viewedfrom the front edge ofworksurface.9"6"3"Legs may be installedinset from the edge of theworksurface to accommodateslip-fit planning. Amount ofavailable space (3", 6", or 9")is measured from the edgeof the worksurface to theedge of the leg. Amount ofslip-fit varies by worksurfaceshape and size.cSee Worksurface LegPositions, page 179.Slip-fit planning allowsworkstation footprint toexpand or decrease, andis ideal for off-moduleapplications..Primary worksurfacewith 28 1 ⁄2"H legs installed at6" or 9" inset can slip overadjacent worksurfaces thatare supported with 26"Hlegs.26"H legs allow worksurfacesto nest underneath anadjacent worksurface with28 1 ⁄2"H legs or a panelmountedworksurface.Pivot hitch can be usedin conjunction with Unisonpedestals and versions ofUnison double wide pedestalswith open shelf to supportworksurfaces.cSee Unison SpecificationGuide..WorksurfacesAnswer Solutions Specification Guide cExtended Corner, Straight-Front and Corner, 120° Worksurfaces, continued 159