Operation Manual - ASSMANN IT-Solutions AG

More documents

Recommendations

Info

1518Rear panel of (optional) battery extension pack:15 DC socket (14Ah only).15a DC connector16 Slots to fasten cable clamps.18 Battery fuse holder(s)7Ah: 2 fuses14Ah: 4 fuses15a16Figure 13. Rear panel batteryextension pack (optional)1518Rear panel of (optional) battery extension pack,equipped with swivel:15 DC socket (14Ah only)15a DC connector18 Battery fuse holder(s)7Ah: 2 fuses14Ah: 4 fuses19 Swivel to fasten cable in terminal cover of UPS15a19Figure 13a. Rear panel batteryextension pack (optional)equipped with swivelOPM_LPE_11X_3K0_10K_1GB_V041 17 GE DE LP 11 UPS: User manual 4.1 (GB)
5.2 Start-upThe numbers between (brackets) refer to figure 12 in section 5.1.Note: the UPS can be started on battery power if the mains input voltage is not available or if MCB‘mains’ is in off-position: simply skip step 1. To prevent accidental discharging of the batteries, it ishowever recommended to proceed with step 1 and start the unit only when the mains input voltage isavailable.1. Turn MCB 'mains' (8) and MCB 'static bypass' (9), both on the rear panel, into position ‘on’ (up).2. Some UPS parameters (e.g. voltage, frequency, LCD language) are user selectable. If you want tochange one or more settings, please refer to section 5.3.4 ‘Set-up Menu’ now. Changing the settingslater is possible, however only after switching off the unit.3. Turn switch 'UPS on/off' (rear panel, 7) into position ‘on’ (up).The green LED 'operation' (front panel, 5) will illuminate.After switching on the UPS performs a self-test and the display (front panel, 1) will show:SELFTESTIN PROGRESSAfter completion of the self-test the output voltage of the UPS is available and the unit is ready for use.The display will show the default screen: model and actual load (values are examples)LP 5-11LOAD 37%In case of a system failure the self-test results in a failure message; this message is displayed for 30seconds before the self-test is repeated automatically. If the faulty situation persists, switch off the UPSand contact your dealer. See chapter 9 for more information.4. Though the batteries (the internal energy reserve) were fully charged when the UPS left the factory,they might have lost some energy during transport and/or storage. It is recommended to allow the UPS torecharge the batteries for a few hours. This way you ensure that the UPS can provide sufficient runtime incase of a mains power failure.5. If not yet switched on, the equipment connected to the UPS can be switched on now; operate as usual.OPM_LPE_11X_3K0_10K_1GB_V041 18 GE DE LP 11 UPS: User manual 4.1 (GB)
Page 6 and 7: 2 - Introduction2.1 DescriptionMore
Page 8 and 9: 3.4 Automatic Bypass SwitchIf the o
Page 10 and 11: 4.5.1 LP 3/5/6-11: standard install
Page 12 and 13: 4.5.3 LP 8/10-11: standard installa
Page 14 and 15: 4.5.5 LP-11 series: 2 / 3 / 4 paral
Page 16 and 17: 4.5.5.3 Notes concerning use / main
Page 20 and 21: 5.3 UseOnce the unit is in operatio
Page 22 and 23: CAPACITOR C1CAPACITY LOWThe main DC
Page 24 and 25: CALIBRATE BATPRESS DOWN+ENTERStart
Page 26 and 27: 5.4 Test ScreensThese screens show
Page 28 and 29: 5.5 Other Features5.5.1 Shutdown'Re
Page 30 and 31: 6 - Interfacing FeaturesThe UPS is
Page 32 and 33: 8.1 General8 - MaintenanceWhen used
Page 34 and 35: 10 - SpecificationsUPS Type : LP 3-
Page 36 and 37: ENVIRONMENTAmbient temperature rang
Page 38: LP 8/10-11 installation drawingMode

Operation Manual - ASSMANN IT-Solutions AG

You also want an ePaper? Increase the reach of your titles

Delete template?

Save as template?